Page 1
SERVICE MANUAL 46P11FZE MT62S-LA 1. Caution 2. Specification 3. Alignment Procedure 4. Block Diagram 5. Scheme Diagram 6. PCB Layout 7. Trouble Shooting 8. Specification of Main IC 9. Explode Diagram 10 BOM List This manual is the latest at the time of printing, and does not...
Page 2
SCHNEIDER ELECTRONICS GMBH-GERMANY 1. CAUTION CA UTION: Use of controls, adjustments or procedures other than those specified herein may result in hazardous radiation exposure. CA UT ION : T O RE DUCE TH E RIS K OF CA U T ION ELECTR ICA L SHOCK, DO NOT RE MOVE COVER (OR BACK).
Page 3
SCHNEIDER ELECTRONICS GMBH-GERMANY IMPORTANT SAFETY INSTRUCTIONS CAUTION: Read all of these instructions. Sa ve these instructions for later use . Follo w all W arnings and Instructions marked on the audio equipment. 1. Read Instructions-All the safety and operating instructionsshouldbe read before the productis operated. 2.
Page 4
SCHNEIDER ELECTRONICS GMBH-GERMANY PROTECTION AND LOCATION OF YOUR SET Do not use this television set near water ... for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. Never expose the set to rain or water. If the set has been exposed to rain or water, unplug the set from the wall outlet and refer servicing to qualified service personnel.
Page 5
SCHNEIDER ELECTRONICS GMBH-GERMANY OPERATION OF YOUR SET 18. This television set should be operated only from the type of power source indicated on the marking label.If you are not sure of the type of power supply at your home, consult your television dealer or local power company. For television sets designed to operate from battery power, refer to the operating instructions.
Page 6
EM BUSINESS CENTER FTV PRODUCT PLANNING DEPT. SPECIFICATION RELEASE Version: V0.1 Issued Date: 2010.03.09 Model: L46P11FZE/MT62S-LA PICTURE Panel Size (inch) 46" Category LCD TV(LED BACK LIGHT) Aspect Ratio 16:9 Color Temperature Warm / Standard / Cold SIGNAL FORMAT CAPABILITY Backlight Adjustable Component Video Format Y, Pb/Cb, Pr/Cr;...
Page 7
Factory Alignment Specification TCL WW R&D FPD CENTER Factory Alignment Specification Chassis MT62S-LA Version V0.1 PREPARED BY : Eric Chen DATE : 2010-04-23 APPROVED BY : DATE : Test Alignment Specification for MT62S-LA.doc (Page 1 of 16)
Page 8
Factory Alignment Specification Disclosure The information contained in this document is proprietary to TCL SZ FPD lab and shall not be disclosed by the recipient to third persons without the written permission of the team leader or GM of R&D.
Page 9
Factory Alignment Specification MT62S-LA chassis is a LA LCD platform with ISDB-T, the main chip is from Mediatek (MTK5362 series) and supports below inputs: x One cable analog RF input (PAL-M /N, NTSC-M) x One antenna analog and digital mixed RF input (PAL-M /N, NTSC-M, ISDB-T) x One AV input x One CMP input (up to 1080P) x One PC input...
Page 10
Factory Alignment Specification 1.2. Download software Download main software with MTK tool. See Appendixn How to download main software. Or download the software from USB port. Download MEMC software with MSTAR ISP tool. See Appendixo How to download MEMC software. 1.3.
Page 11
Factory Alignment Specification 2. Final Assembly Alignment 2.1. Entering to “Factory Menu” To enter into Factory Menu in case of “Factory Hotkey” is disabled, please to follow below steps : - P ress Remote Control key “MENU” to display main menu, and move the cursor to “Contrast”...
Page 12
Factory Alignment Specification 2.3. White Balance Alignment Only HDMI input requires color temperature adjustment, all other inputs are relative to it. Both Warm and Cool Color Coordinate are relative to Normal Color Temperature mode. See Appendix “CVBS/RGB/CMP/VGA Relative Matrix Offset and WARM/COOL Relative Matrix Offset”. Those offsets values don’t require any alignment but can be fine-tuned in Factory Menu as well.
Page 13
Factory Alignment Specification 3. Factory Menu Definition 3.1 System Item Sub-item Value Remarks OFF hotkey is invalid Factory Hotkey Off/On hotkey (blue key) is availability OFF display according signal Warm Up Off/On display burning picture if no signal On: Enter power on mode System Power On Mode On/Standby/Last...
Page 14
Factory Alignment Specification 3.4 White Balance Item Sub-item Value Remarks Source YPbPr White Press “OK” key to run /VGA/HDMI/ Balance TV/AV /S-VIDEO Color temperature Cool RGB gain range is 0-255 /Standard The value of Warm and cool is the offset of /Warm Normal mode, their range is -128 127, if the offset value beyond the boundary set to max...
Page 15
Factory Alignment Specification Brightness curve Item Sub-item Value Remarks Brightness _0 Brightness Curve Brightness _25 Brightness _50 Brightness _75 Brightness _100 (Other) Item Sub-item Value Remarks Back Light Param Setting Phase 3.6 Version Info SW version information Item Sub-item Value Remarks Version Project...
Page 16
Factory Alignment Specification Appendix How to download main software 1. Connect PC to connector P16 with USB serial device. 2. Power on the chassis. 3. Start “MTKTOOL.exe”, and set the parameters as below picture: 4. Press “Browse” button to select the corresponding bin file to upload. 5.
Page 17
Factory Alignment Specification Appendix How to download MEMC software 1. Connect PC to connector PM3 with MSTAR ISP tool. 2. Power on the chassis. 3. Start “ISP_Tool.exe”. 4. Select “Config”, set “ISP Slave Address” to “0X94”, set “I2C Speed Setting” to around 200K. 5.
Page 18
Factory Alignment Specification Appendix CVBS/RGB/CMP/VGA Relative Matrix Offset and WARM/COOL Relative Matrix Offset These offsets should be done in the production by AOE. Appendix IC should be pre-copied before SMT process: Test Alignment Specification for MT62S-LA.doc (Page 12 of 16)
Page 19
Factory Alignment Specification Appendix Select panel ID with hyper-terminal 1. Connect PC to connector P16 with USB serial device. 2. Power on the chassis. 3. Start “Hyper-terminal” in below Windows path: Start Program Accessory Communication Hyper-terminal 4. Name the new connection. 5.
Page 20
Factory Alignment Specification 6. Com port setting as below, select “File” ”Save” to save the setting. Test Alignment Specification for MT62S-LA.doc (Page 14 of 16)
Page 21
Factory Alignment Specification 7. Transport the handshake txt file. Test Alignment Specification for MT62S-LA.doc (Page 15 of 16)
Page 22
Factory Alignment Specification 8. Following “DTV>”, input: “pmx.s.p” + “ID No.”, and then enter. The rolling up message show what panel is set to current panel setting. For example: pmx.s.p 104 Test Alignment Specification for MT62S-LA.doc (Page 16 of 16)
Page 45
8. Trouble Shooting Standby power OK, no Power ON signal Check L44 Replace L44 3.3V OK? Replace U201 or Check U201 X54M and X54M Replace Q100 Check Q100 C 3.3V OK? Check and repair the Peripheral components...
Page 46
Power OK no backlight no raster Check Q9 C Replace Q9 high voltage Replace Q10 Check Q10 C high voltage Check Q14 Replace Q14 Pole C 0V Check Q1 Replace Q1 Pin8 12V Check and repair the PM2...
Page 47
Power OK backlight OK,no raster Check Q14 Replace Q14 Pole C 0V Check Q1 ReplaceL140 Pin 1 12V /L139 CheckQ1 Replace Q1 Pin 8 12V Check voltage LVDS signal Replace LVDS cable or T-CON board...
Page 48
AV no picture All source no picture Check circuit from scart to U201 Software of U14 Update replace software of U14 VGA no picture VGA no picture Check Check Q37 and Replace Q1 U201 OK? U29’VCC replace Check Replace T-CON T-CON board board cable...
Page 49
picture Check Replace pin_6 is 5V L119,L135 Check the components from Check TU1 pin_10 FAT- to FAT_INPUT- pin_11 Check the components from FAT+ to FAT_INPUT+ Replace X54M Replace TU1 and U201...
Page 50
Picture ok, all source no sound Check R190 and Replace U201 R191 ok? Check L165 Replace U25 and L167 ok? Check L6 3.3v Replace L6 Replace L7 Check L5 and Check speaker Check Q700 cables or speaker Pole C is low Check Q700, Q701,Q915...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Document Revision History Revision Date Author Description 2008-07-29 Antony Liao & DL Huang Initial Draft 2008-09-18 Cassy Liu Add DVBT and modify VDEC & DRAM feature 2008-10-16 Antony Liao Add power consumption data 2008-11-14 DL Huang Update...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Legal Notice This data sheet contains information that is confidential to MediaTek Inc. Unauthorized use or disclosure of the information contained herein is prohibited. You may be held responsible for any loss or damages suffered by MediaTek Inc.
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice GENERAL DESCRIPTION The MediaTek MT5362ANG/B family is a backend decoder and a TV controller and offers high integration for advanced applications. It combines a transport de-multiplexer, a high definition video decoder, an AC3 audio decoder, a dual-link LVDS transmitter, and an NTSC/PAL/SECAM TV decoder with a 3D comb filter (NTSC/PAL).
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice GENERAL FEATURE LIST Host CPU ARM 926EJS 16K I-Cache and 16K D-Cache 8KB Instruction TCM JTAG ICE interface Watch Dog timers Build-in CPI analyzer and Cache Hit Rate Meter ...
Page 58
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Still Image decoding JPEG (base-line or progressive) De-mosquito engine 2D/3D for all AV inputs 2D Graphics Supports multiple color modes Point, horizontal/vertical line primitive drawings ...
Page 59
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice 3:2/2:2 pull down source detection Supports maximum 1920 width motion-adaptive de-interlace. Supports excellent low angle image processing. Arbitrary ratio vertical/horizontal scaling of video, from 1/32X to 32X ...
Page 60
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice 2 channel on chip Audio ADC Audio digital input 1 bit I2S audio input HDMI Receiver HDMI1.3, data rate can be up to 2.25 GHz ...
Page 61
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Bass management 3D surround processing with virtual surround Audio and video lip synchronization Supports reverberation Automatic volume control Supports 5-bit (10-channel) main audio I S output interface: each of these channels is up to 24-bit resolution.
Page 62
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice IR blaster and receiver Real-time clock and watchdog controller The MT5362ANG/B includes 2-link USB2.0/1.1 (supports external hub) for USB mass storage class device. Built-in uP in standby module ...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice PIN DESCRIPTION of MT5362ANG/B Pin Number Symbol Type Driving Description Note Miscellaneous AB11 ORESET_ Chip reset TP_VPLL VPLL test port JTAG JRTCK 2~8 mA CPU ICE Reference clock Reference clock ce clock JTCK CPU ICE test clock...
Page 66
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice OIRO 2~8 mA Infrared output Power Management AD10 OPCTRL0 2~8 mA Power management GPIO 0 AC10 OPCTRL1 2~8 mA Power management GPIO 1 AB10 OPCTRL2 2~8 mA Power management GPIO 2 OPCTRL3 2~8 mA Power management GPIO 3...
Page 67
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice RDQ6 8.1~10.1 mA memory data bit 6 RDQ7 8.1~10.1 mA memory data bit 7 RDQ8 8.1~10.1 mA memory data bit 8 RDQ9 8.1~10.1 mA memory data bit 9 RDQ10 8.1~10.1 mA memory data bit 10 RDQ11 8.1~10.1 mA...
Page 68
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice 2~8 mA LVDS Tx even channel negtive output bit 1 2~8 mA LVDS Tx even channel positive output bit 2 2~8 mA LVDS Tx even channel negtive output bit 2 2~8 mA LVDS Tx even channel positive output bit 3 2~8 mA...
Page 69
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice GPIO1 2~8 mA General Purpose I/O GPIO2 2~8 mA General Purpose I/O GPIO3 2~8 mA General Purpose I/O GPIO4 2~8 mA General Purpose I/O GPIO5 2~8 mA General Purpose I/O GPIO6 2~8 mA General Purpose I/O...
Page 70
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Anaog VideoOutput VDAC_OUT1 VDAC1 output VDAC_OUT2 VDAC2 output VDAC Reference pin IFADC input VINDC Add capacitor to stabilize power VIP_ATV IF input+ VIN_ATV IF input- Servo ADC input AA26 ADIN0_SRV Servo ADC input channel 0 C input channel 0 channel 0...
Page 71
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice CI_MCLKO 4~16 mA CI output interface: Clock CI_MDO0 4~16 mA CI output interface: Data CI_MOVAL 4~16 mA CI output interface: Valid CI_MOSTRT 4~16 mA CI output interface: Sync CI_MCLKI 2~8 mA CI input interface: Clock CI_MDI0 2~8 mA...
Page 72
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice AVDD33_USB Analog power, 3.3V AVDD33_USB Analog power, 3.3V AVDD33_VDAC Analog power, 3.3V AVDD33_VDAC_BG I Analog power, 3.3V AVDD33_XTAL Analog power, 3.3V DVDD25_IFADC IFADC power, 2.5V AVSS_LVDS Analog ground AVSS_LVDS Analog ground AVSS_LVDS Analog ground AVSS12_MEMPLL...
Page 76
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice RCKE 8.1~10.1 mA memory clock enable RCS_ 8.1~10.1 mA memory chip select RODT 8.1~10.1 mA memory on die termination enable RRAS_ 8.1~10.1 mA memory row address strobe RWE_ 8.1~10.1 mA memory write enable Page 26 of 35 MEDIATEK CONFIDENTIAL, NO DISCLOSURE...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice MT5362ANG/B GPIO 5362B Default Pull Slew Stand Symbol Interrupt To.(V) ball Pull Up/Down Rate by *1 U0TX Program Program Program 5 rogra U0RX Program Program Program 5 ram Program AD10 OPCTRL0 Level Program Program Program 5...
Page 78
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice POWE_ Level Program Program - PAALE Level Program Program - PACLE Level Program Program - PDD0 Level Program Program - PDD1 Level Program Program - PDD2 Level Program Program - PDD3 Level Program...
Page 79
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice CI_MDO0 Level Program Program - CI_MCLKO Level Program Program - CI_MOVAL Level Program Program - CI_MOSTRT Level Program Program - CI_MDI0 Level Program Program - CI_MCLKI Level Program Program - CI_MIVAL Level Program...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice POWER-ON SEQUENCE Power on Sequence AC ON NORMAL MODE STANDBY MODE AC OFF NORMAL MODE SBV33 POWER ON CONTRO DV11 AV33 DV33 AV125 AV25 DDRV Crystal EXTERNAL RESET RNAL RESET POWER DETECT POWER DETECT POWER DETE...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice CRYSTAL SPECIFICATION Parameters Value Unit Nominal Frequency Oscillation Mode 3-rd Overtone Load Capacitance Frequency Tolerance (25°C) ±30 ±30 Effective Series Resistance Operation Temperature Range -20~ +80 -20~ +80 -20~ +8 °C Crystal Input Pin Swing (XTALI) >500...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice ELECTRICAL CHARACTERISTICS Absolute Maximum Rating Symbol Parameters Value Unit VCC3_STDBY Standby 3.3V supply voltage -0.5 to 4.6 -0.5 to 4.6 VCC3IO 3.3V supply voltage -0.5 to 4.6 -0.5 to 4.6 -0.5 to 4.6 VCCK 1.0V supply voltage...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice Thermal Characteristics Symbol Parameters Value Unit Storage Temperature -40 to 150 Ambient Temperature 0 to 65 Case Temperature 0 to 95 Tjmax Maximum Junction operation temperature jc-BGA-4LPCB BGA package junction to case thermal resistance on 4 layer PCB ja-BGA-4LPCB BGA package junction to ambient thermal resistance on 4 Layer PCB yer PCB...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice 10 OUTLINE DIMENSION (Note: Ball diagram is bottom view) Page 34 of 35 MEDIATEK CONFIDENTIAL, NO DISCLOSURE...
MT5362ANG/B Approval Datasheet Specifications are subject to change without notice 11 TOP MARKING DDDD: Date Code ###: Subcontractor Code nnnnnnn: Lot Number MT5362ANG DDDD-B##L nnnnnnn Page 35 of 35 MEDIATEK CONFIDENTIAL, NO DISCLOSURE...
Page 91
08-PE421C1-PW300AA 67-M60442-1E0 TV RAW SPRING GND-15 00 01 R=Y 08-PE421C1-PW300AA 67-M60442-1E0 TV RAW SPRING GND-15 00 01 R=Y 08-PE421C1-PW300AA 67-M60442-1E0 TV RAW SPRING GND-15 00 01 R=Y 08-PE421C1-PW300AA 28-CB0105-KBX CAP.CER,SMD 1U0F 50.0V 1206 - C427 08-PE421C1-PW300AA 19-CD0332-JTX SMD. RES 3.3K OHM 1/4W 5% R425 08-PE421C1-PW300AA 19-BC0470-JTX SMD.RES 0805,1/8W,±5%,47Ω...
Page 92
08-PE421C1-PW300AA 57-893390-0UG RAW HOLDER SPACE -- 00 00 R=Y 08-PE421C1-PW300AA 57-893390-0UG RAW HOLDER SPACE -- 00 00 R=Y 08-PE421C1-PW300AA 57-893390-0UG RAW HOLDER SPACE -- 00 00 R=Y 08-PE421C1-PW300AA 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) D203 08-PE421C1-PW300AA 10-0FR104-FBX DIODE FR104 (FAST RECTIFIER) D206 08-PE421C1-PW300AA 19-CD0109-JTX SMD.RES 1 OHM 1/4W +/-5%...
Page 93
T8-NP11S8A-FC1 54-808030-0U0 SPONGE BAR 中框底部贴2条(左右各1条)1MM厚海绵 T8-NP11S8A-FC1 54-808030-0U0 SPONGE BAR 音箱两端包一圈海绵条 T8-NP11S8A-FC1 54-892340-200 RAW OVERLAY KEY BACKLIGHT -- 02 00 00 R= T8-NP11S8A-FC1 54-893840-000 TAPE-ADH RAW ADHESIVE TAPE 55258 -- R=Y 粘接按键板和按键支架 T8-NP11S8A-FC1 54-889490-1UH RAW INSULATOR POWER PCB INLAY -- 00 01 T8-NP11S8A-FC1 62-891020-0HZ RAW SUPPORT 46P11 SPK -- 0HZ 00 00 R=N...
Page 115
ASS'Y - PACKING(ART)ASY T8-NP11S8A-PA5Z 02-891340-0001A PAI STAND 46P11 -- 00 -- 00 R=Y T8-NP11S8A-PA5Z 70-STDP11-ADD1B TV PRI ADDENDUM SHEET P11 BASE INSTALLAT T8-NP11S8A-PA5Z 72-MT62SL-EEM1A IB MT62S-LA TCL R=Y T8-NP11S8A-PA5Z 74-022032-5WEEM DEC BAG -- R=Y T8-NP11S8A-PA5Z 74-150105-50HEM DEC BAG -- R=Y T8-NP11S8A-PA5Z 76-898060-0AT...