Easy wave RCP24 Quick Start Manual

RCP24 Plug-In Radio Bell
EN
Models
Button P | LED P
Programming
Speaker
Flashing light
RCP24E5001A01
Technical Details
Frequency: 868.30 MHz
Modulation: FSK
Coding: Easywave
Range: up to 150 m under
favourable open field
conditions
Power supply: 230 V AC 50 Hz
Power consumption: 0.2 W Standby
1.1 W (at max. load)
Current consumption: 2 mA Standby
Operating temperature: -20 °C to +35 °C
Transport and storage
temperature: -20 °C to +75 °C
Max. relative air humidity: 75%
Volume at a distance
of 30 cm: low:
medium: 85 dB(A)
high:
Dimensions (H/W/D): 71.4/71.4/40 mm
without plug
71.4/71.4/75.5 mm
with plug
Weight: approx. 115 g
Scope of Delivery
Plug-in radio bell RCP24, operating instructions
Intended Use
The device may only be operated indoors and
only as a radio bell.
The manufacturer will not be liable for damage
caused by improper or inappropriate use.
Safety Advice
Please read these instructions carefully
before using the device!
- We do not accept any liability for personal
injury or damage to property caused by
incorrect handling or non-observance of the
safety instructions!
- Do not open the appliance's casing! Have
malfunctioning devices checked by the ma-
nufacturers!
- Do not make any unauthorized alterations or
modifications to the unit!
Function
The Plug-In Radio Bell RCP24 receives Easy-
Button
wave transmission codes from programmed
LED
transmitters. Once the transmission button is
Volume
pressed, a melody will sound and/or a light will
begin to flash.
A total of 32 transmission codes can be program-
med into the unit.
12 multichannel melodies are available to choose
from as ringtones. The melodies can be played at
three volume levels (approximately 80 dB, 85 dB,
and 90 dB). If the radio bell is muted (0 dB), re-
cognized Easywave telegrams are signalled only
by the flashing light.
Battery level monitoring
Some Easywave transmitters include battery mo-
Flashing
nitoring. The RCP24 can evaluate low-battery vol-
light
tage telegrams issued by these transmitters.
Programming
Programming the Transmitter
You activate the programming mode of the
RCP24 by briefly pressing the P button multiple
times.
Each press moves the selection forward by one
melody, and there are twelve melodies available
in total. When you hear your preferred melody,
press the transmitter button you wish to program
within 30 seconds to complete the programming
process.
Select melody

Button P press once briefly (< 1.6 s)
MELODY 1 is selected
LED P flashes red, Melody 1 is played
Button P press twice briefly (< 1.6 s)
MELODY 2 is selected
LED P flashes red, Melody 2 is played
80 dB(A)
Button P press three times briefly (< 1.6 s)
MELODY 3 is selected
90 dB(A)
LED P flashes red, Melody 3 is played
etc.
 Programming transmission code
Press the button on your transmitter. The me-
lody is assigned to the transmission code and
saved in the RCP24. The LED P lights up red
for 2 seconds.
The RCP24 then switches to operating mode
and the LED P switches off.
The programming process will be automa-
tically cancelled if no buttons are pressed
for 30 seconds.
To manually cancel programming, press
the P button briefly repeatedly until it is no
longer flashing.
Change Melody
If you would like to change the melody of a pro-
grammed transmitter, simply re-program the
transmitter into the RCP24, and choose your pre-
ferred melody.
The previous selection will be overwritten.
The relevant operating instructions will tell you
whether a transmitter supports this function.
If it is detected that the battery level in a program-
med transmitter is low, this is signalled by alter-
nate flashing of the buttons and double-beeping
twice after the ringtone sounds.
Start Up
1. Plug the radio bell into an electrically and
structurally intact protective contact socket;
an acknowledgement tone will sound and a
light will briefly flash.
2. Transfer the transmitter coding to the radio
bell (see section titled "Programming the
transmitter").
Make sure that there is no interference with
the wireless connection. Do not mount the
device in a distribution box, metal casings
or in direct proximity to large metal objects.

Button P
Press the button briefly
repeatedly (< 1.6 s) until
the desired melody is
played
Transmit transmission code

Transmission button Tx
press (< 1.6 s)
or
Connect voltage
(RTS17)
Select or change
the melody
Programming the
transmission code