Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Devon BLAZER 9000
- Page 1 BLAZER 9000 LUBE LIFT OPERATOR AND PARTS MANUAL Blazer 9000 Lube Lift Operator’s Manual Note: Instructions must be read thoroughly before installing, operating, or maintaining the lift. Devon Industries 800-468-1970 Fax: 405-943-3882 01-01-2021...
- Page 2 8. Capacity of the Blazer 9000 is 9000 lbs. Do not exceed the 9000 lb. capacity. Placing a Vehicle on the Blazer 9000 Note: It is critical that the operator positions the lift points per the vehicle manufacturers recommended lift points.
-
Page 3: Installation Instructions
4. The bases must be aligned perfectly and the same distance apart. 5. Shim as required to level both sides of the lift. 6. The Blazer 9000 can be surface mounted or recessed mounted. Optional ramps are required if the unit is to be surface installed. - Page 4 Layout Dimensions...
- Page 5 Layout Dimensions...
-
Page 7: Hydraulic Connections
1. Concrete must be level and uniform and have a thickness of 4” with a rating of 3000PSI. The concrete should be reinforced with wire and rebar. 2. When installing the Blazer 9000 on a concrete floor that has a basement, you should check with the building architect or manufacturer to determine the proper support for the lift. - Page 8 Air Connections 1. The Blazer 9000 has air safety releases, which require that an air system be installed. 2. The air valve can be mounted on the optional power unit stand referenced above. 3. Maximum air pressure on the system is 50-60 PSI. Use regulator to control pressure and water filter to keep system dry.
- Page 9 AIR BLEEDING PROCEDURE FOR BLAZER 9000 Step #1 Fill the power unit reservoir with Dexron III Mercon Automatic Transmission Fluid or equivalent, approximately 7.5 quarts to start with, check all connections for proper security and clearances around and under both of the lifting surfaces, example,…. binding, chafing, and pinching.
-
Page 10: Maintenance
MAINTENANCE DAILY 1. Keep all movement points clean, dry and lightly lubricated. 2. Always keep bolts tight. 3. Check for oil leaks. 4. Keep air regulator set @ maximum 50-60 PSI. 5. Remove any accumulated moisture from air line filter. 6. - Page 11 TROUBLESHOOTING THE LIFT 1. Motor does not run: Breaker or fuse blown. Motor thermal overload tripped. Defective UP switch. Replace Faulty wiring connections. Call electrician. ————————————————————————————————————————————- 2. Motor runs but lift will not raise: Trash is under the release valve. Push Down button and push Up button at the same time.
- Page 12 The structural components of Blazer 9000 Lube Lift are warranted to the original owner to be free from defects in material and workmanship under normal use for a period of years from invoice date. Devon Industries, Inc. will replace those parts returned to the factory which prove to be defective for the two year warranty period.
-
Page 13: Warranty Registration
———————————————————————————————————————————— WARRANTY REGISTRATION... - Page 14 PARTS MANUAL – BLAZER 9000...
- Page 16 PARTS LIST - BLAZER 9000 Only use manufacturer supplied replacement parts ITEM# PART# Description 92422 TOP PLATE STRUCTURE LH 92423 TOP PLATE STRUCTURE RH 92402 BASE STRUCTURE - LH 92403 BASE STRUCTURE - RH 95169 ANCHOR BOLTS 5/8X3-3/4 92429 LIFTING LEG...
-
Page 18: Hydraulic Schematic
HYDRAULIC SCHEMATIC PART# PART NAME 95170 Power Unit HYD. Hose - Long (RH or LH) HYD. Hose - Long (RH or LH) 92413RH HYD. Cylinder - RH 92413RH...
Need help?
Do you have a question about the BLAZER 9000 and is the answer not in the manual?
Questions and answers
Who manufactures the BL-Blazer 9000 lifts?
The Devon BLAZER 9000 lifts are manufactured by DEVON Industries, Inc.
This answer is automatically generated