Page 1: Table Of Contents
2.3.8 Scan Type 2.2 Key Function 2.3.9 Scan Display 2.2.1 Power ON / OFF 5 2.310 Threshold 2.2.2 Power Meter 2.2.3 Scan 2.2.4 dB / dBm 2.2.5 Graph 2.2.6 Recall 2.2.7 Save ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 2: Introduction
2.8” TFT-LCD, 16 bit Color Battery / Power Rechargeable Lithium-Polymer – 7 hr. Operating Temperature -20° ~ +55° C Weight 13 oz* Dimensions h / w / d 7 x 3.25 x 1.5 (inches)* *w/boot ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 3: Package Contents
- Do not subject the CO-OPM-MPO24 to strong impact. - The CO-OPM-MPO24 is not water resistant or waterproof - Do not disassemble. Always properly clean the fiber interfaces before taking a measurement. Always replace the Dust Cap for dust protection. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 4: Getting Started
Recall saved measurements ▼ Move down in a menu/page down in result screen SAVE Save measurement to meter memory Cancel or move back to previous menu MENU Access System Menu and settings ENTER Enter ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 5: Key Function
2 seconds, the logo shown appears. The meter then displays the channel with the highest power level. Press the button for Backlight more than 2 seconds to turn the power off. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 6: Power Meter
Press the button, mode will change “Auto” to “Manual” and vice versa. ▲ ▼ You can select the different wavelengths using Press the button to change the inspection wavelength. λ ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 7: Scan
This button toggles between dB (relative) & dBm (absolute) power measurements dB/dBm To measure the relative loss of an MPO circuit, connect the CO-OPM-MPO24 to a known light source with a short (test) jumper. (continued) ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 8 A graph is also available. Remove test jumper and replace with jumper to be measured SCAN Press scan: The relative loss of the jumper will be displayed on both the table and graph. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 9: Graph
Contents CO-OPM-MPO24 2.2.5 Graph Graph button is used after scanning to show power levels in graphical format. Scroll to view fibers 13-24 Press the Graph button again it returns to text mode. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 10: Recall
The following message shows, and the measurement is saved using the current date and time as the filename. Then, press the button ENTER – to save. To abort saving, press • ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 11: Menu
Time Set Data Delete Data Format System Info Scan Display and Threshold 2.3.1 Polarity Use this option to change the polarity of the measurement. Straight (Type A) Rollover (Type B) Flipped (Type C) ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 12: Offset
You can set the time between 5 to 600 Min. by pressing the number key button. ENTER – ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 13: Time Set
– selecting ‘Time Set’ , to set the date and current time. Enter date in YY/MM/DD format Enter time in HH/MM/SS format You can save the time by pressing button. ENTER – ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 14: Data Delete
ENTER – choosing the data you want to delete, the message appears on the screen to confirm to delete or not. Press the button, to ENTER – delete measurement from the memory. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 15: Data Format
CAUTION: This option deletes ALL DATA saved on the meter. 2.3.7 System Info General information about the equipment. PN - Product Name SN - Serial Number HW - Hardware version FW - Firmware version ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 16: Scan Type
‘Measured’ . This can be selected using ▲ ▼ ‘All’ will display power level on all 24 fibers. If you choose the ‘Measured’ , the value of the selected channel is output. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...
Page 17: Threshold
‘-30.00 dBm’ is the default setting. ENTER Press the button after – selecting ‘Threshold’ , you can set the baseline. Baseline changes can be found at the graph screen. ChallengerOptics.com Wavelength Specific Optical Testing and Measurement Equipment...