WYTRON MagicCD Series Operation Manual

Cd/dvd duplication controller card

Advertisement

MagicCD / MagicDVD Series
CD/DVD Duplication Controller Card
DVD-319, CD-398, DVD-399, DVD-668, DVD-688
Operation Manual
Wytron Technology Co., Ltd.
Aug., 2005
http://www.wytron.com.tw
e-mail:
wytron@wytron.com.tw

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MagicCD Series and is the answer not in the manual?

Questions and answers

Summary of Contents for WYTRON MagicCD Series

  • Page 1 MagicCD / MagicDVD Series CD/DVD Duplication Controller Card DVD-319, CD-398, DVD-399, DVD-668, DVD-688 Operation Manual Wytron Technology Co., Ltd. Aug., 2005 http://www.wytron.com.tw e-mail: wytron@wytron.com.tw...
  • Page 2: Table Of Contents

    CONTENT Introduction Caution Installation Operation Main Function Copy Copy + Comp Emulate Emu + Copy Compare Quick Erase Verify Load (if HDD installed) External Sub-function Setup 6.1.1 Start Writers 6.1.2 Write Method...
  • Page 3 6.1.3 CD Write Speed 6.1.4 DVD Write Speed 6.1.5 CD-ROM Drive 6.1.6 Autoloader (if autoloader installed) 6.1.7 Eject Disc 6.1.8 Buzzer 6.1.9 CD+G 6.1.10 CopyComp Eject 6.1.11 Read CDDA index0 6.1.12 Skip Read Error 6.1.13 MODE 2 Compare 6.1.14 Power On Wait 6.1.15 Show version 6.1.16 Go load trays 6.1.17 Transfer mode...
  • Page 4 6.1.23 Hdd Partition Group (if HDD installed) 6.1.24 HD to CD Write Speed (if HDD installed) 6.1.25 HD to DVD Write Speed (if HDD installed) 6.1.26 Grip before accept 6.1.27 Load Nonblank Disc (if HDD installed) 6.1.28 CDDA load speed (if HDD installed) 6.1.29 Language (for DVD-6xx series only) Edit Delete...
  • Page 5: Introduction

    Do not move the duplicator during operation. DO NOT remove the serial number labels attached on controller card. Warranty will be VOID if any label is torn off or damaged. Wytron reserves the right to fix those cards without labels.
  • Page 6 Warranty will be VOID if the controller card has been tampered with. Wytron will not accept to repair these controller cards even within warranty. The controller card must be maintained in the original shipped status to comply the warranty condition, no artificial...
  • Page 7: Caution

    Wytron shall not be liable for any hardware used with the product, including the costs of repairing, replacing, or recovering such hardware.
  • Page 8: Installation

    Installation You may get MagicCD or MagicDVD series duplicator in three possibilities: Controller only Prepare necessary devices including: IDE bus CD/DVD-ROM drive IDE bus CD/DVD writer. Suitable tower case. Hard drive. Switching power supply (Appropriate capacity is suggested. Bad quality of power supply might damage the controller board and cause unstable operation.
  • Page 9 Model:DVD-688 EIDE data cables DRV #2 DRV #3 DRV #4 DRV #5 DRV #6 DRV #9 DRV #8 DVD-688 DRV #10 DRV #11 DRV #7 CD/DVD-ROM Hard drive (Situation in max. connection)
  • Page 10 Model:DVD-668 EIDE data cables Hard drive CD/DVD-ROM DVD-668 IDE #2 IDE #3 IDE #4 IDE #5 IDE #6 (Situation in max. connection)
  • Page 11 Model:CD-398/DVD-399 EIDE data cables IDE #2 IDE #3 IDE #4 IDE #5 IDE #6 CD-398/DVD-399 IDE #7 IDE #8 IDE #9 IDE #10 CD/DVD-ROM Hard drive (Situation in max. connection)
  • Page 12 Note: Since CD-398/DVD-399 is nine-target (10 EIDE ports on-board) controller board, the power consumption will be higher than that supplied by usual 300W power supply unit. We strongly recommend using 400W power supply unit to avoid lack of power. Lack of power supplying will cause unstable of operation and produce un-usable products.
  • Page 13 tower case is much easier to be located in the market). Please refer to the sketches shown above to install your CD-398/DVD-399/DVD-668/DVD-688 duplicator. If less than 9 writers are connected on CD-398/DVD-399, please first remove the connection of red slot and then others (even number slot) in sequential.
  • Page 14 Model: DVD-319 to install three targets Controller card Controller CD/DVD writer (slave) IDE#2 CD/DVD writer (master) IDE#2 CD/DVD writer (slave) IDE#1 ROM or hard drive IDE#1 (Set to master mode) Note: Please be noted that all the devices in the case, including the DVD-319 controller card, CD/DVD-ROM and CD/DVD writer, must be connected with 4-pin power cable which holds 12V (in yellow color), 5V (in red color) and two black...
  • Page 15 ROM and hard drive on same channel. In this case, please set hard drive to master and slave to ROM. Be noted the USB interface is a standard device when you purchase the DVD-319 bare bone (Wytron two-bay chassis).
  • Page 16 Assemble the duplicator according to your need. Make sure that the voltage setting is correct. Customers can purchase the optional Wytron USB 2.0 module that enables you to link one of the writers in the duplicator to PC for external usage.
  • Page 17: Operation

    Operation Power on the system and you will see a self-testing procedure running. The following display will appear: CD398 V3.17 2004 WYTRON TECHNOLOGY detect drives …… Copy AG234M14:23 <mode AG234M14:23 Length of Master contained in hard drive. It varies from masters or may not exist if there is no data stored.
  • Page 18 AA. With hard drive installed Duplicator will automatically detect the hard drive and create partitions for it (each partition will have 850MB capacity for CD duplicator, e.g. 40 GB Hard Disk will probably have 44 partitions. For DVD duplicator, 4.8GB or 9.6GB for each partition.) You can select partition in the “hdd partition group”...
  • Page 19 When Copy is completed on all writers, those discs passed will be ejected automatically (default setting: Passed discs will be ejected but this can be changed according to your need). For continuous duplication, place additional blank discs into the writers and repeat the above procedures.
  • Page 20 only one target.) or neither there is any limitation on sequence of writer to start with. In other words, you may copy one disc only by using any one of the writers randomly. When Copy is completed, the passed discs will be ejected automatically (Default setting: discs passed will be ejected.
  • Page 21 The message shown after function is finished: OK x NG x TOK xxxxx (Copy for example) C3852+00 16x12 05:38 OK x: The passed target number for current operation NG x: The failed target number for current operation TOK xxxxx: The counter for total passed target number for operation in current function Note: The TOK (Total in OK) counter will be reset when the master is reloaded (from CD/DVD-ROM) or...
  • Page 22: Main Function

    Main Function Main functions explained below (Copy, Copy+Comp, Compare, etc.) are based on factory’s default setting. Different settings will cause duplicator to react differently. Please press and keep holding down the MODE switch while turning on the power till the “clear setup” message is shown on the LCD; the duplicator will return to factory’s default setting as a reset.
  • Page 23: Copy + Comp

    Copy + Comp This function will do copying and also comparing the passed discs with the master. Under this function, the discs that passed in copying will be ejected and re-inserted again automatically for compare purpose. The passed discs will be ejected automatically after comparison.
  • Page 24: Emu + Copy

    Emu + Copy This function combines the emulation and copy function within one selection. First the machine will do the emulation and then continually copy the disc if there is no error during emulation. The passed discs will be ejected and the failed ones will be remained in the writers.
  • Page 25: Load (If Hdd Installed)

    Number of partitions available depends on the hard drive’s capacity. No pre-formatting or software setup is required to install the hard drive with Wytron’s controller card. Each partition in hard drive will be labeled in alphabetical order starting from AA, AB, AC…etc. Current partition number can be selected under “hdd partition...
  • Page 26 Wytron’s USB 2.0 interface card will be available for external usage. At this moment, users can link an external USB cable from remote PC to duplicator, thus the PC will auto-detect the USB device in duplicator for ®...
  • Page 27: Sub-Function

    Sub-function In main menu, press and keep holding down the MODE switch for more than five seconds till the da-da-da sound heard from the controller, the menu will be switched to sub- menu and vice versa. Setup As there are different settings under the setup function to control the duplicator’s operation, we suggest using the original default settings for optimal operation.
  • Page 28: Write Method

    6.1.2 Write Method This setting controls the writing methods of CD/DVD disc including “Disc at once” or “Track at once”. “Disc at once” will be the default setting. Some writers may support different writing methods. If the method selected is not supported, duplicator will automatically switch to the other one.
  • Page 29: Cd-Rom Drive

    There is also situation that un-authorized blank DVD disc will be locked and restricted in some DVD writers to write at higher speed. This situation is not under Wytron’s control. Press MODE to change the setting and GO to exit.
  • Page 30: Eject Disc

    COM port module from Wytron to communicate between controller card and autoloader. If no autoloader is connected actually but set this option by mistake to one of the types for autoloader, during new power booting, the controller card will hang in “check loader…”...
  • Page 31: Cd+G

    6.1.9 CD+G This setting activates the copy capability of CD+G format. It cannot be copied if the writers don’t support this format. Default setting is “No”. Press MODE switch to change and GO to exit. 6.1.10 CopyComp Eject This setting controls the ejection of writers’ trays under “copy + compare”...
  • Page 32: Mode 2 Compare

    error message. If the setting is “Yes”, there will be no message shown even there is an error in reading. You can use this function to copy some discs with errors. Press MODE switch to change and GO to exit. 6.1.13 MODE 2 Compare This setting can be activated to compare some data format stored in “MODE 2”...
  • Page 33: Transfer Mode

    setting of this function, customer can load first the discs onto all trays on drives and force those trays to insert with pressing the “Go” button once on controller card. Default setting is “No”. Press MODE to change the setting and Go to exit. 6.1.17 Transfer mode This function controls the data transfer mode between connected devices with controller card and there are three...
  • Page 34: Turbo Copycomp

    BIOS programming, compared to traditional programming on Wytron’s products. Several conditions must be complied to make this option work: (a) For DVD only (b) Master hard drive or master DVD-ROM to be connected at IDE#1 or...
  • Page 35: Startup Command

    After completing the password changing, system will record the 4 digits password and when you reboot the machine or need to change the password again, system will ask you to input the current password for identification. Password can be changed again by setting Yes to the Change Password function but the current password must be input correctly first.
  • Page 36: Hdd Partition Size (If Hdd Installed)

    User just needs to connect the hard drive on the Wytron’s controller card and then the controller card will handle the partition job automatically. All the data stored in hard drive...
  • Page 37: Hdd Partition Group (If Hdd Installed)

    When the CD writers are originally connected on Wytron’s DVD controller cards, with hard drive installed, the 850M partition size would be used. If user installs a DVD writer suddenly for testing purpose, the hard drive would be re-partitioned automatically by 4.8G or 9.6G, depending on the DL or SL supported on this DVD writer.
  • Page 38: Hd To Cd Write Speed (If Hdd Installed)

    The modern hard drives normally contain large capacity. In order to organize and utilize the capacity well, controller card will manage the capacity in an idea for two-level management: partition group and partition number. The partition group is somewhat like the category and the partition number is the sub-item in that category.
  • Page 39: Hd To Dvd Write Speed (If Hdd Installed)

    or unstable CD writing in high speed. Under this circumstance, please lower the writing speed under this setting to get higher successful rate. On the contrary, lower value setting will make the writing speed slower and confuse you as a problematic duplicator. Press MODE to change the setting and GO to exit.
  • Page 40: Load Nonblank Disc (If Hdd Installed)

    6.1.27 Load Nonblank Disc (if HDD installed) This setting is mainly for Autoloader and controls the loading of non-blank disc in any writer. If setting is “Yes”, whenever there is a non-blank disc detected by the writer, the duplicator will go to “Load” function automatically and start loading the data from that non-blank disc into current partition of hard drive.
  • Page 41: Edit

    Edit Edit function, in sub-function, is a track-selecting function that can combine tracks on different master discs into one single disc. For example, you can make a collection of favorite songs from different master music discs and store them into one disc. Switch to “Clear”...
  • Page 42 at “Begin track” and press once again GO at “End track” to exit. Duplicator will start loading those music tracks selected into the current partition of hard drive. After finishing loading, the master disc will be ejected automatically and LCD will display the message of “Pass”.
  • Page 43 instructions step by step. You will find it is very easy to collect tracks by the duplicator. Example 1: To make collection from two masters with hard drive installed. No.1 master disc: 2, 4, 6-8 songs. No.2 master disc: 3-6, 9, 13-16 songs. a.
  • Page 44 o. Once the accumulated length of tracks selected has exceeded the maximum capacity in partition. The duplicator will stop to accept additional tracks. p. Switch to “Delete” function to delete the last track stored in current partition in hard drive if necessary. q.
  • Page 45 and press GO switch to quit. When “End track” is displayed on the LCD, press GO switch to quit directly since the number shown is already 2. Press MODE switch to number 5 at “Begin track” and press GO to quit. When “End track”...
  • Page 46: Delete

    Delete When the last music track stored in hard drive is not the one you wish to keep, switch to “delete” function and press GO switch to delete it. You may always use this function to delete the last track stored in the current partition of hard drive.
  • Page 47: Burn In

    DVD-ROM [*] ATA1.0 1.22 It means the first slot (IDE#1) on controller board is connected with DVD-ROM that is set to master mode (0) and its firmware version is 1.22. ATAPI DVD+RW 4X4X [*] ATA7.1 B1HY It means the 7 slot (IDE#7) on the controller board is connected with ATAPI device DVD+RW writer that is set to slave mode (1) and its firmware version is B1HY.
  • Page 48: Update

    Procedures to make the BIOS disc by yourself: 1. Get the BIOS firmware from Wytron through e-mail (wytron@wytron.com.tw). Be careful not to use the wrong firmware, as it will cause duplicator to hang up and not to function correctly.
  • Page 49: Reset

    Reset The reset procedure is required for several reasons such as: First assembling of duplicator, changing new brand of writers in old duplicator, wrong setting for certain function or bring back the factory’s default setting according to different usages. Our design provides an easy way for customer to reset their controller cards as below: Turn off the power of duplicator and wait for 10 seconds.
  • Page 50: Circuit Drawing

    Circuit drawing DVD-688 Controller Card LCD / CONTROL HDD / DVD-ROM POWER...
  • Page 51 DVD-668 Controller Card LCD / CONTROL HDD & CD / DVD-ROM POWER...
  • Page 52 CD-398/DVD-399 Controller card LCD / CONTROL COM2 COM1 CD/DVD-ROM / HDD POWER...
  • Page 53 DVD-319 Controller Card LCD / CONTROL CD/DVD-ROM / HDD WRITER POWER...
  • Page 54: Trouble Shooting

    Trouble shooting 1Q: No display or only black squares on LCD display and the unit does not boot when power on. A: Please check the connection of power cable and the power environment is normal. B: Please check the fan of power supply. It should rotate if power-on.
  • Page 55 Change the option of “CD-ROM drive” to switch the present CD/DVD-ROM into another one for testing. 4Q: Switches do not function. Maybe still busy on task. Switch blocked. Button malfunction. Faulty board. Screws too tight for the button board. 5Q: COPY completed but CD/DVD disc is not readable / executable? A: Use Compare function to check.
  • Page 56: Device Support

    Device support For IDE CD-ROM: ATAPI compatible CD/DVD-ROM reader. Note: The default CD write speed on controller card is set to 32X due to poor reading performance on normal CD/DVD-ROM reader. If higher write speed is required, please install a hard drive and then copy from the hard drive to CD-R.
  • Page 57 For IDE CD-R/RW writer Plextor W4012TA/W4824TA/W5232TA Sanyo or Nichimen 1300 / 1400 / 1500 / 1600 / 1700 AOpen 48X, 52X Acer 8432IA Lite-On LTR-40125/48125/52246 Yamaha 8824E / 2100E / 2200E / 3200E / CRW-F1 Teac W524E / W540E / W552E Traxdata or BTC 40X, 48X, 52X.
  • Page 58: Appendix

    SERVICE, PLEASE ADVISE FULL DETAILS OF THE SYMPTOMS. Please provide necessary information listed below when requesting the BIOS program from Wytron to make the technique support efficiently: 1. Model number of controller card. 2. Current BIOS version on controller card.

This manual is also suitable for:

Magicdvd seriesDvd-319Cd-398Dvd-399Dvd-668Dvd-688

Table of Contents