Summary of Contents for Focalcrest MIXTILE IEC-EDGE2-0432
- Page 1 IEC-EDGE2-0432 | Single Board Computer User Manual Get Started with https://www.mixtile.com/wiki/...
-
Page 2: Product Description
Edge 2 – User Manual MIXTILE 1 Introduction 1.1 Product Description Edge 2 is a high-performance and rich-interface ARM64 single-board computer targeted for a wide range of IoT networking and computing applications. It may apply in networking, computing, controlling, and home entertainment areas for further achievement with the help of multipurpose software. - Page 3 Edge 2 – User Manual MIXTILE 1.4 Key Component Specifications The key component specifications are described below with relevant hardware information and developing notices. For more information, pin assignments and signal descriptions are listed in Chapter 2, Connectors & Pin Assignments. 1.4.1 MIXTILE Core 3568 The Core 3568 is a System-on-Module that expands all CPU functions to pins with an innovative...
- Page 4 Edge 2 – User Manual MIXTILE 1.4.3 MicroSD Socket The MicroSD socket accepts standard 11mm x 15mm Micro-SD cards with capacities up to 64GBytes. The 4bits data interface supports the SDMMC3.0 protocol. The default boot setting is the eMMC Flash which can change to the MicroSD card. 1.4.4 M.2 Socket M.2, Next Generation Form Factor (NGFF), is specified for expansion modules.
- Page 5 Edge 2 – User Manual MIXTILE 1.4.6 Gigabit Ethernet The IEEE802.3 compliant ethernet supports 10/100/1000Mb half-duplex and full-duplex auto- negotiation. The GbE communicates to an external PHY, RTL8211F-CG, through an RGMII interface from the processor. The RJ45 connector contains status and speed lights. The green light is on for connected and flashing for data transmitting.
- Page 6 Edge 2 – User Manual MIXTILE MIPI-DSI The MIPI-DSI display supports two channel DSI and 2.5Gbps maximum data rate per lane. It supports up to 1920x1080@60Hz display output for single-MIPI mode and 2560x1440@60Hz for dual-MIPI mode. Two MIPI-DIS interfaces use 30-pin FPC connectors, MIPI-DSI0 MIPI-DSI1 , which include one channel MIPI-DSI and one touch panel signal (TP).
-
Page 7: Connectors & Pin Assignments
Edge 2 – User Manual MIXTILE 2 Connectors & Pin Assignments The following section lists the interfaces connector pin assignments, pin types with corresponding signal descriptions. The interface connectors on Edge 2 are listed in the table below. 2.1 Debug Input/ Signal Description Name... -
Page 8: Power Button Connector
Edge 2 – User Manual MIXTILE 2.4 I2C Input/ Signal Description Name Type Output 3.3V Output 3.3V @ 100mA Max I2C3_SCL Output I2C clock signal I2C3_SDA I2C data signal Ground 2.5 5V Output Input/ Signal Description Name Type Output Output 5V @ 2A Max in total Output 5V @ 2A Max in total Ground Ground... - Page 9 Edge 2 – User Manual MIXTILE 2.9 RS485 Input/ Signal Description Name Type Output Ground 485B RS485 differential signal Negative 485A RS485 differential signal Positive 2.10 ADC Input/ Signal Description Name Type Output 3.3V Output 3.3V @ 100mA Max SARADC_VIN4 ANA Input ADC analog signal SARADC_VIN5 ANA...
- Page 10 Edge 2 – User Manual MIXTILE 2.13 MIPI-DSI0 Input/ Signal Description Name Type Output Ground MIPI_DSI_TX0_D0N LVDS Output MIPI-DSI0 data signal Negative MIPI_DSI_TX0_D0P LVDS Output MIPI-DSI0 data signal Positive Ground MIPI_DSI_TX0_D1N LVDS Output MIPI-DSI0 data signal Negative MIPI_DSI_TX0_D1P LVDS Output MIPI-DSI0 data signal Positive Ground MIPI_DSI_TX0_CLKN...
- Page 11 Edge 2 – User Manual MIXTILE Ground MIPI_DSI_TX1_D1N LVDS Output MIPI-DSI1 data signal Negative MIPI_DSI_TX1_D1P LVDS Output MIPI-DSI1 data signal Positive Ground MIPI_DSI_TX1_CLKN LVDS Output MIPI-DSI1 clock signal Negative MIPI_DSI_TX1_CLKP LVDS Output MIPI-DSI1 clock signal Positive Ground MIPI_DSI_TX1_D2N LVDS Output MIPI-DSI1 data signal Negative MIPI_DSI_TX1_D2P LVDS...
- Page 12 Edge 2 – User Manual MIXTILE EDP_TX_D2P LVDS Output EDP data signal Positive Ground EDP_TX_D3N LVDS Output EDP data signal Negative EDP_TX_D3P LVDS Output EDP data signal Positive 3.3V Output 3.3V @ 500mA Max in total 3.3V Output 3.3V @ 500mA Max in total Ground Ground EDP_HPD_GPIO0_C2...
- Page 13 Edge 2 – User Manual MIXTILE CAMERA0_RST_L_GPIO4_B5 Output GPIO output for camera reset CAMERA0_PDN_L_GPIO4_B4 Output GPIO output for camera disable CAMERA0_PWREN_GPIO1_D4 Output GPIO output for camera enable I2C4_SCL_M0 Output I2C clock signal I2C4_SDA_M0 Input I2C data signal PWM14_M0 Output PWM Output signal Ground Ground Output...
- Page 14 Edge 2 – User Manual MIXTILE Not connected pin Ground Not connected pin PCIE30_TX1_N/HUB_USB3_SSTXN LVDS Output PCIE3.0/USB3.0 data signal Negative M2_UIM_RESET Input Reset signal to SIM socket PCIE30_TX1_P/HUB_USB3_SSTXP LVDS Output PCIE3.0/USB3.0 data signal Positive M2_UIM_CLK Input Clock signal to SIM socket Ground M2_UIM_DATA Input...
- Page 15 Edge 2 – User Manual MIXTILE Not connected pin 3.8V Output 3.8V @ 3A Max in total Ground 3.8V Output 3.8V @ 3A Max in total Ground 3.8V Output 3.8V @ 3A Max in total Not connected pin 2.18 Mini-PCIe Input/ Signal Description Name...
- Page 16 Edge 2 – User Manual MIXTILE Not connected pin Not connected pin Ground Ground USB2_HOST2_DM LVDS USB2.0 data signal Negative Not connected pin USB2_HOST2_DP LVDS USB2.0 data signal Positive 3.8V Output 3.8V @ 3A Max in total Ground 3.8V Output 3.8V @ 3A Max in total Input System status LED...
- Page 17 Edge 2 – User Manual MIXTILE Ground Ground Output 5V @ 3A Max Output 5V @ 3A Max Output 5V @ 3A Max Ground Not connected pin Ground Not connected pin Not connected pin Not connected pin SATA0_LED Output SATA0 status for LED SATA2_LED Output SATA2 status for LED...
-
Page 18: Specifications
Edge 2 – User Manual MIXTILE SATA2_TXN LVDS Output SATA data signal output Negative SATA2_TXP LVDS Output SATA data signal output Positive Ground SATA2_RXN LVDS Input SATA data signal Input Negative SATA2_RXP LVDS Input SATA data signal Input Positive Ground PCIE20_REFCLKN LVDS Output... -
Page 19: Technical Support
Edge 2 – User Manual MIXTILE 4 Support 4.1 Technical Support MIXTILE technical support team assists you with the questions you may have. Contact us with the following methods below. Email: support@mixtile.com Website: https://www.mixtile.com V1.1 Copyright © 2021 MIXTILE. - Page 20 FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.