Table of Contents
Advertisement
Quick Links
BH1600, BH1700, BH2150, BH2150N, BH2200, BH2350
Rotary hummer T.I.P. - a reliable tool that can operate in three modes:
drilling, drilling with impact, hammer drilling. The tool is intended for
breaking, drilling, scraping in concrete and other similar materials, such as
piping, cables, installation of plumbing products, other materials.
1 – closing sleeve;
2 – side stick;
3 – rear handle;
4 – power cord;
ROTARY HAMMER
OPERATING MANUAL
Fig. 1
5 – power switch;
6 – mode switch "impact",
"drilling", "drilling with impact".
1
EN|ENGLISH
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Vega BH1600
- Page 1 EN|ENGLISH ROTARY HAMMER BH1600, BH1700, BH2150, BH2150N, BH2200, BH2350 OPERATING MANUAL Rotary hummer T.I.P. - a reliable tool that can operate in three modes: drilling, drilling with impact, hammer drilling. The tool is intended for breaking, drilling, scraping in concrete and other similar materials, such as piping, cables, installation of plumbing products, other materials.
- Page 2 EN|ENGLISH SAFETY WARNING! Carefully read all instructions. Failure to follow all the instructions mentioned below, can cause electric shock, fire and / or serious personal injury. 1. Keep your work area clean and well lit. Cluttered surfaces and darkened room may be the cause of the accident. 2.
-
Page 3: Additional Safety Rules
EN|ENGLISH 14. Use only accessories recommended by the the manufacturer for your model. Spare parts that fit a single instrument can be dangerous for an- other. ADDITIONAL SAFETY RULES 1. Always wear a safety helmet (helmet), goggles and / or face shield, and is recommended to use a dust mask, ear protectors and thick cotton gloves. - Page 4 EN|ENGLISH Model BH1600 BH1700 BH2150 BH2150N BH2200 BH2350 Power 1600 W 1700 W 2150 W 2150 W 2200 W 2350 W Voltage 220 V 220 V 220 V 220 V 220 V 220 V Current 50 Hz 50 Hz 50 Hz...
- Page 5 EN|ENGLISH Fig. 3 1. Clean the tool shank (item 1. Figure 2) and lightly grease with grease grease (Item 2, Figure 2). 2. Pull back the locking sleeve (item.2. Figure 3) 3. With the simultaneous rotation of the tool in the tool, enter the slot (Item 4.
- Page 6 EN|ENGLISH Fig. 4 ATTENTION! • Switch mode can only be in a position to a full stoppunch. • In the process of drilling, hammering action is prohibited to put a lot of effort hammer, it can only slightly be sent. The increased effort does not increase the force of impact, and only creates unnecessary extra load on the engine! •...
- Page 7 EN|ENGLISH Fig. 5 Fig. 6 Setting the bit Before you install the bit, make sure that the drill is turned off and unplugged. The lever mechanism of the shock set in an intermediate position. Now, the bitYou can manually rotate to the desired position. Then againset the lever mechanism of the shock to position "bit."...
-
Page 8: Using The Tool
EN|ENGLISH Fig. 7 USING THE TOOL The inclusion of punch ATTENTION! Before operating the tool, always check the efficiency ofswitch, after releasing it should easily return to the position"Off' Fig. 8 Fig. 9... - Page 9 EN|ENGLISH To activate the tool, simply click on the switch (position 8, Figure 8). To turn off the machine release the switch (position 8,9). ATTENTION! As soon as the dutch worked, immediately turn off the machine. This will allow You to avoid overload of the motor. The work of a jackhammer Put the lever mechanism of the shock to the "bit".
-
Page 10: Maintenance
EN|ENGLISH MAINTENANCE Always before performing preventive maintenance work and ensure that the tool is switched off and unplugged from the outlet. For safe and reliable operation of the instrument, keep in mind that the repair. Maintenance and adjustment of the instrument should be in service centers using only original spare parts and consumables. -
Page 11: En|English
EN|ENGLISH CE DECLARATION OF CONFORMITY We Vega Trade Company Limited as the responsible manufacturer declare rotary hammer TM Procraft: that BH1600, BH1700, BH2150, BH2150N, BH2200, BH2350 are of series production and сonfirm to the following European Directives: 2006/42 / EС...
Need help?
Do you have a question about the BH1600 and is the answer not in the manual?
Questions and answers