Summary of Contents for Baoding Longer Precision Pump EasyPump Series
Page 1
Shenchen Precision Pump Manual of EasyPump Series Baoding Shenchen Precision Pump Co.,Ltd...
Page 2
Note: Please read the manual carefully before using the product. Warning: Tubing may crack due to wear, which results in overflow of fluid from the tubing. In that time human body and instruments may be harmed. So, users must check frequently and change tubing in time.
Shenchen Pump EasyPump Series Product Introduction Easy-load type pump head has brand new design which gives customer brand new experience. Not only the appearance is attractive, the function design is also more practical. The unique tube clamp linkage mechanism, with the opening process of the upper block, the tube clamp naturally lifts, and the user can easily put in the tube.
Shenchen Pump EasyPump Series According to tubing size, channel numbers and tube pressure gap, the EasyPump model No. as below: Tubing Wall Tube Pressure Model No. Tubing Size Channel Thickness 13#,14#,19#,16#,25#, EasyPump I 1.6mm Single Fixed 17#,18# EasyPump II 2.4mm...
Page 6
Shenchen Pump EasyPump Series Dual-channel, fixed tube pressure gap pump head: Lever Upper pressure block Body base Upper tube clamp Roller assembly Lower tube clamp Lower support Rubbing wheel Single channel, adjustable tube pressure gap pump head: Pressure adjusting knob...
Page 7
Shenchen Pump EasyPump Series Dual channel, adjustable tube pressure gap pump head: Pressure adjusting knob Upper pressure block Body base Lever Upper tube clamp Roller assembly Lower support Lower tube clamp Rubbing wheel 2.1 Single Pump Head Installation (1) Standard (flat) shaft pump head installation with rubber coupler...
Page 8
Shenchen Pump EasyPump Series Rubber coupler Pump head screw (2) Round shaft pump head installation with plum blossom coupler Install the plum blossom coupler on the pump head shaft, adjust to suitable position, fasten the coupler screw. Then install the pump head on the driver motor shaft with coupler, fasten the pump head screws to fix the pump head on the driver.
Page 9
Shenchen Pump EasyPump Series (1) Pump heads are connected in series as a whole. (Take three pump heads as an example) The pump head status as in below picture when you receive it. Remove the two M4 nuts, install the complete pump head group (pump ...
Page 10
Shenchen Pump EasyPump Series (2) The pump heads are separate, or users need to disassemble and replace the pump head in the later use process, please refer to the below instruction: The main shaft connection between two adjacent pump heads needs to ...
Page 11
Shenchen Pump EasyPump Series Take off the lower support decoration as in below picture: Turn the lever counterclockwise 180°to open the upper pressure block, then use a flat-blade screwdriver to insert into the buckle position as shown in below picture, pry open the buckle position with a slight force, and then remove the lower support decoration.
Page 12
Shenchen Pump EasyPump Series 2.3 Tubing Installation Pull the lever 180 ° counterclockwise and open the upper pressure block. Put the tubing between rollers and upper pressure block. Pull the lever 180 ° clockwise, and push upper pressure block to the ...
Page 13
Shenchen Pump EasyPump Series 2.4 Tubing Installation Note Before you press the upper pressure block, please make sure the tubing has been straighten when tubing installed. Otherwise, it will cause the tubing accumulating in the pump head, leading to the tube deviates to scratch itself in a running process, as below: ×...
Page 14
Shenchen Pump EasyPump Series × × √ When the tubing needs to be bent installed, it does not set aside enough length and space to cause the tubing inside the pump head work part deviation, tubing will be cut, as below: ×...
Shenchen Pump EasyPump Series Function Instruction 5.1 Adjustable Function for Position of Lower Tube Clamp Adjust the rubbing wheel to adjust the position of the lower tube clamp position, to make the pump head fit for different size tubing. Note: Please adjust the lower tube clamp position first before install tubing.
Page 20
Shenchen Pump EasyPump Series 5.1.2 The lower tube clamp position will move downward when two sides of rubbing wheel rotates in a counterclockwise direction as below: 5.1.3 Low tube clamp position for different size tubing instruction: (1) When the lower tube clamp is at the top, it can fit for: 1.6mm wall thickness tubing: 13#, 14#, 19#, 16#, 25#.
Page 21
Shenchen Pump EasyPump Series (2) When the lower tube clamp is at the middle position, it can fit for: 1.6mm wall thickness tubing, size: 17#, 18# 2.4mm wall thickness tubing, size: 15#, 24# Just for single channel. The lower tube clamp display white color.
Page 22
Shenchen Pump EasyPump Series Pharmed tube. If need to use other material tubing, please contact with us for technical support. 5.2 Tube Pressure Gap Adjustable Function Adjust the pressure adjusting knob to adjust the tube pressure gap, to change the pump head tube output pressure and flow rate.
Shenchen Pump EasyPump Series will increase, and flow rate will reduce. Turn the knob counterclockwise, the scale value will reduce, tube pressure gap will increase, the output pressure of the pump head tube will reduce, and flow rate will increase.
Shenchen Pump EasyPump Series Maintenance When pump is not working, please loose the cartridges of pressing the tubing for avoiding changing the shape of tubing because of longtime extrusion. Keep the rollers of pump head clean and dry, otherwise it can quicken ...
Shenchen Pump EasyPump Series Warranty and After Sales Service We support 1 year warranty for the pumps, subject to the exceptions below. Our company shall not be liable for any loss, damage, or expense directly or indirectly related to or arising out of the use of its products. This warranty...
Page 28
MADE IN CHINA Baoding Shenchen Precision Pump Co., Ltd. Address: No.103, Building 2, ZhiDian Industrial Park, FuXing East Road 999, 071000 Baoding, China. Tel: 0086-312-5958380 Fax: 0086-312- 6780636 Website: www.good-pump.com Email: info@good-pump.com...