Advertisement
Quick Links
Octagon Greenhouse
AssEmbLy InsTruCTIOn
Rear View
PO Box 455, Berlin, OH 44610 • 330-893-4212 • www.cottagekits.com
All manuals and user guides at all-guides.com
mAnuAL
- Cordless Drill (12V or higher)
- #2 Square Drive Bit
- Hammer
LITTLE COTTAGE CO.
8x8 Octagon Greenhouse
Size: 8'x8'
Tools Needed:
- Tape Measure
- Utility Knife With Blade &
Hook Blade
- Speed Square
- 5/16" Wood Drill bit
© 2019 Little Cottage Co.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Little Cottage Octagon
Summary of Contents for Little Cottage Octagon
- Page 1 - #2 Square Drive Bit - Utility Knife With Blade & - Hammer Hook Blade - Speed Square - 5/16” Wood Drill bit Rear View LITTLE COTTAGE CO. PO Box 455, Berlin, OH 44610 • 330-893-4212 • www.cottagekits.com © 2019 Little Cottage Co.
- Page 2 All manuals and user guides at all-guides.com Octagon Greenhouse AssEmbLy InsTruCTIOn mAnuAL Locate 4x4 runners for 8x8 Octagon Green- Next locate the 8 pieces of rim and joist. house. Layout 4x4’s as shown. Here you see the 8 pieces of rim.
- Page 3 The 2 longest 4x4’s need to be in the center. Next place shorter 4x4’s as shown. Next pic- Keep 4x4 flush with rim and secure with 2 1/2” ture will be more detailed. Zinc Screws as shown. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 4 The plywood is all cut. You may have to lay Next secure plywood to joint and rim as the flooring out before you fasten anything to shown using 1 1/4” Zinc Screws. make sure the pieces are placed properly. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 5 Secure wall panel A with 2 1/2” screws as Repeat on opposite end. shown. make sure corners line up and put pres- sure on the outside pushing in so wall is tight against floor as shown. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 6 Both reveels need to be the same. Continue with walls. Make sure the inside corner is in place and secure with 2 1/2” Zinc screws as shown. Installing walls. All walls are installed except door wall. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 7 Barrel bolt is installed and 3/16” hole is Locate door latch which will be in a white drilled. This is what it looks like when completed. box. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 8 Next secure D-lever on inside. Secure D-lever with 1 1/4” black headed screws. Install L-bracket to keep door closed. Use 1 Door latch is completed. 1/4” blackhead screws to secure L-bracket. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 9 Insert 2 1/2” screws in an angle to tie top plates together. Next locate all the rafters and roof parts. Install first rafter to Octagon as shown at pencil marked as shown. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 10 Secure rafter to top plate and make sure Secure 2x3 that is attached to rafters into corners of rafters line up with the edge of the top 2x6 top plate with 2 1/2” screws. plate as shown. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 11 Secure rafter with 2 1/2” screws. doing the top. After all rafters are installed and fastened, Secure blocks with 2 1/2” screws as shown. fill in blocks that are cut on angles in between rafters. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 12 2 1/2” screws. Continue installing 2x3 rafters. Next locate metal roof corners and sunsky. Metal corners installed. Push metal corner up until it is against top and secure with 1 1/4” Zinc Screws. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 13 Metal corner installed. Metal corners are done. Weather-striping Next locate weather-striping and sunsky roof- Place the weather-striping under the sunsky ing. roofing. Install the sunsky roofing as shown. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 14 Roof will overhang trim roughly 1”. Secure with 1” white screws with rubber washer. Install second piece as shown and repeat. 1” overhang Insert screws beside each rip as shown. Continue with screws. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 15 Keep flush with top of window sill and secure with 2 1/2” screws. Deck screws are pro- vided for treated shelves. Continue with shelf installation. Continue installing shelves on 7 walls. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 16 The short braces will be installed on end shelves. Same on the bottom. If wood wants to split use 1/8” drill bit and drill hole where screw is shown to go through. Assembly Instruction Manual © 2019 Little Cottage Co.
- Page 17 All manuals and user guides at all-guides.com Octagon Greenhouse AssEmbLy InsTruCTIOn mAnuAL 8x8 Octagon greenhouse is complete! Shelves are completed. Assembly Instruction Manual © 2019 Little Cottage Co.
Need help?
Do you have a question about the Octagon and is the answer not in the manual?
Questions and answers