Table of Contents
Advertisement
Quick Links
1.
OVERVIEW.......................................................................................................................................... 1
2.
INSTALLATION................................................................................................................................... 3
2.1. CARE AND HANDLING OF OPTICAL FIBER............................................................................ 4
2.1.1. Safety .............................................................................................................................. 4
2.1.2. Assembly......................................................................................................................... 4
2.1.3. Labeling........................................................................................................................... 4
2.1.4. Handling and Connecting Fibers ..................................................................................... 5
3.
SPECIFICATIONS............................................................................................................................... 6
3.1. SERIAL VIDEO INPUT ............................................................................................................... 6
3.2. OPTICAL OUTPUT..................................................................................................................... 6
3.3. DATA OUTPUT........................................................................................................................... 6
3.4. ELECTRICAL ............................................................................................................................. 6
3.5. COMPLIANCE ............................................................................................................................ 7
3.6. PHYSICAL .................................................................................................................................. 7
4.
STATUS INDICATORS AND DISPLAYS ........................................................................................... 8
4.1. STATUS INDICATOR LEDS....................................................................................................... 8
4.2. DOT-MATRIX DISPLAY ............................................................................................................. 9
4.2.1. Displaying the Video Standard ........................................................................................ 9
4.2.2. Signal BLOCK Configuration......................................................................................... 10
4.2.3. Setting the Behavior of Laser When There is No Applied Video................................... 10
4.2.4. Setting the Orientation of the Text on the Card Edge Display....................................... 10
4.2.5. Displaying the Firmware Version................................................................................... 10
5.
JUMPERS AND LOCAL CONTROLS .............................................................................................. 11
BY THE GLOBAL FRAME STATUS ........................................................................................ 11
5.2. CONFIGURING THE MODULE FOR FIRMWARE UPGRADES .............................................. 11
6.
®
V
6.2. V
®
TABLE OF CONTENTS
? ............................................................................................................... 12
®
MONITORED PARAMETERS .............................................................................. 12
7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter
Revision 1.0
7700 MultiFrame Manual
Advertisement
Table of Contents
Related Manuals for Everlz 7708VT-4
Summary of Contents for Everlz 7708VT-4
-
Page 1: Table Of Contents
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter TABLE OF CONTENTS OVERVIEW............................1 INSTALLATION........................... 3 2.1. CARE AND HANDLING OF OPTICAL FIBER................4 2.1.1. Safety ..........................4 2.1.2. Assembly......................... 4 2.1.3. Labeling........................... 4 2.1.4. Handling and Connecting Fibers ..................5 SPECIFICATIONS.......................... - Page 2 ISTA ® Figures Figure 1-1: 7708VT-4 Block Diagram........................2 Figure 2-1: 7708VT-4 Rear Panel ......................... 3 Figure 2-2: Reproduction of Laser Certification and Identification Label.............. 4 Figure 4-1: Location of Status Indicators and Jumpers ..................8 Tables Table 6-1: VistaLINK Monitored Parameters.....................
- Page 3 7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter REVISION HISTORY REVISION DESCRIPTION DATE Original Version Feb 09 Information contained in this manual is believed to be accurate and reliable. However, Evertz assumes no responsibility for the use thereof nor for the rights of third parties, which may be affected in any way by the use thereof.
- Page 4 Never look directly into an optical fiber. Non-reversible damage to the eye can occur in a matter of milliseconds. Do not hook up the 7708VT-4 DWDM and 7708VR-4 cards directly with a short fiber optic cable. The 7708VT-4 DWDM card produces +7dBm of power which will damage the receiver if connected directly.
-
Page 5: Overview
DWDM DFB laser output, yyy – ITU channel number The 7708VT-4 occupies one card slot and can be housed in either a 1RU frame, which will hold up to three modules, or a 3 RU frame, which will hold up to 15 modules. -
Page 6: Figure 1-1: 7708Vt-4 Block Diagram
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter Features: • Single card TDM multiplexer for four synchronous or asynchronous 270Mb/s SDI, SDTi or DVB- ASI video signals • Output compatible with SMPTE 292 reclocking devices • Signal transport over fiber uninterrupted by loss of any SDI, SDTi or DVB-ASI input feed •... -
Page 7: Installation
7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter INSTALLATION The 7708VT-4 comes with a companion rear plate that has five BNC connectors and one SC/PC (shown), ST/PC or FC/PC optical connector. For information on mounting the rear plate and inserting the module into the frame see section 3 of the 7700FR chapter. -
Page 8: Care And Handling Of Optical Fiber
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter 2.1. CARE AND HANDLING OF OPTICAL FIBER 2.1.1. Safety CLASS 1 LASER PRODUCT Background colour: yellow Triangular band: black Symbol: black 2.1.2. Assembly Assembly or repair of the laser sub-module is done only at Evertz facility and performed only by qualified Evertz technical personnel. -
Page 9: Handling And Connecting Fibers
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter 2.1.4. Handling and Connecting Fibers Never touch the end face of an optical fiber. Always keep dust caps on optical fiber connectors when not connected and always remember to properly clean the optical end face of a connector before making a connection. -
Page 10: Specifications
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter SPECIFICATIONS 3.1. SERIAL VIDEO INPUT Standard: SMPTE 259M-C, SMPTE 305M, DVB-ASI Number of Inputs: 4 independent SDI or DVB-ASI, 270Mb/s signals Connector: 4 BNC per IEC 61169-8 Annex A Return Loss: > 15dB up to 270Mb/s 3.2. -
Page 11: Compliance
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter 3.5. COMPLIANCE Electrical Safety: CSA Listed to UL 60065-03, IEC 60065 Complies with CE Low voltage Directive Laser Safety: Class 1 laser product Complies with 24 CFR 1040.10 and 1040.11 Complies with IEC 60825-1... -
Page 12: Status Indicators And Displays
This Green LED indicates good module health. It will be On when a valid input signal is present, and the laser and board powers are good. On the 7708VT-4, there are four small LEDs on the back of the board that indicate the presence of video signals. -
Page 13: Dot-Matrix Display
DISP Displays the present Firmware version. 4.2.1. Displaying the Video Standard The 7708VT-4 detects the Video standards of the signal present at its input. CH1-CH4 To display the Video Standard, press the pushbutton and actuate the toggle switch until CH 1, CH 2, CH 3 or CH 4 message is shown on N270 the display. -
Page 14: Signal Block Configuration
4.2.3. Setting the Behavior of Laser When There is No Applied Video On the 7708VT-4 the LASR display allows you to set the behavior of the laser transmitter when there is no video signal applied to the coaxial video inputs. -
Page 15: Jumpers And Local Controls
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter JUMPERS AND LOCAL CONTROLS Several jumpers, located at the front of the module are used to preset various operating modes. Figure 4-1 shows the locations of the jumpers. 5.1. SELECTING WHETHER LOCAL FAULTS WILL BE MONITORED... -
Page 16: Vistalink ® Remote Monitoring/Control
(GUI), third party or custom manager software may be used to monitor and control Evertz VistaLINK enabled fiber optic products. ® 2. Managed devices (such as 7708VT-4 and 7708VR-4 cards), each with a unique address (OID), communicate with the NMS through an SNMP Agent. Evertz VistaLINK enabled 7700 series modules ®... -
Page 17: Controlled Parameters
7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter 6.3. LINK CONTROLLED PARAMETERS ISTA ® The following parameters can be remotely controlled through VistaLINK interface. ® Parameter Description Allows user to change password that is needed in Change Password order to enable/disable video channels... - Page 18 7700 MultiFrame Manual 7708VT-4 Quad SDI/ASI Fiber/Coax Transmitter This page left intentionally blank Page-14 Revision 1.0...
Need help?
Do you have a question about the 7708VT-4 and is the answer not in the manual?
Questions and answers