1. Manuals
  2. Brands
  3. Pinnovators Manuals
  4. Pinball Machine
  5. PinPAC TH2
  6. Installation manual

Pinnovators PinPAC TH2 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PinPAC TH2
Installation Manual
for
Stern Spike 2 Pinball
Machines
330.202.00
Version 1.1 March 06, 2022
1
Contents
Warnings and Agreements ................................ 2
1.
What's included in the Kit.......................... 3
2.
Requirements ............................................ 4
3.
Preparation ................................................ 4
4.
Back Box Installation .................................. 5
5.
cabinet ............................................................... 7
6.
7.
8.
Reassembly .............................................. 11
9.
Setup Menu Adjustments ........................ 11
Setup menu Part 1: .................................. 11
Setup menu Part 2: .................................. 13
10.
Closing Statements .............................. 14

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PinPAC TH2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Pinnovators PinPAC TH2

Summary of Contents for Pinnovators PinPAC TH2

  • Page 1: Table Of Contents

    Back Box Installation ........5 Running the cable through the main cabinet ............... 7 Removing the Tournament Hole Plug..8 Installing the PinPAC TH2 Plate....8 Reassembly ..........11 Setup Menu Adjustments ......11 Setup menu Part 1: ........11 Setup menu Part 2: ........

  • Page 2: Warnings And Agreements

    Pinnovators requires our kit be installed by an experienced pinball service technician with basic electrical skills. As with any electrical piece of equipment a danger does exist and you must agree to not hold Pinnovators responsible for any injury, damages, etc.

  • Page 3: What's Included In The Kit

    1. What’s included in the Kit Item Part Number Picture PinPAC TH2 Front Panel Assembly 310.202.000 Back Plate 100.054.000 Cable 600.057.000 PinPAC TH2 Hardware Kit: 600.053.001 ¼ 4-40 Inch Nuts 441.005.000...

  • Page 4: Requirements

    2. Requirements A. The Pinnovators PinPAC TH2 for Stern Spike 2 systems requires a Tournament hole on the front of the Pinball cabinet. B. Tools: A ¼ Inch hollow tube nut driver. You can purchase the tool here if you do not have one.

  • Page 5: Back Box Installation

    4. Back Box Installation Lower the front speaker grill and remove the back glass. Store the glass in a safe location. Uncoil the included interface cable. This cable has two connectors on it. Cable End Plugs into Picture 5 Pin Front Headphone Interface Panel 7 Pin CN3 on the CPU board.
  • Page 6 Plug the 7-pin connector into the CN3 Male pin header on the Spike 2 CPU board. Run the cable under the cable clamp. No need to remove the cable clamp, just tug on the top of it to open it. Run cable under the second cable clamp and then drop the remaining cable into the main cabinet.

  • Page 7: Running The Cable Through The Main Cabinet

    5. Running the cable through the main cabinet Remove the playfield glass and lift up the playfield as shown. REMOVE THE PINBALLS! Run the cable through the cable clamps as shown below. Leave any leftover cable slack neatly here so the cable will not get stretched when the back box is folded down.

  • Page 8: Removing The Tournament Hole Plug

    7. Installing the PinPAC TH2 Plate. Insert the PinPAC TH2 Front panel into the open Tournament hole. The volume control faces up. Future product revisions will be slightly different than what is shown here.
  • Page 9 Thread the green ground wire and the pin header cable through the slotted opening of the PinPAC TH2 rear mounting plate as shown. Hand tightten the two 4-40 lock nuts onto the Pem studs of the PinPAC TH2 front plate.
  • Page 10 Remove the ¼ inch screw on the lock down latch and then fasten the mid lug of the green safety wires are shown. Caution!! You must attaches these ground wires as show!! Make sure the screw is snug when you screw it back in. If for some reason, the hole is stripped (like mine was on my Aerosmith) completely remove the bracket and repair the hole! Please contact us if you need help.

  • Page 11: Reassembly

    8. Reassembly Lower the playfield and reinstall the pinballs. Reinstall the playfield glass. 9. Setup Menu Adjustments Power up your game! There are two menu sections we will need to adjust now that the headphone kit is installed. Beware! You may need to power cycle the machine to get a menu setting to work properly! You can make the setting, but it may not fully work until the power is cycled or the game menu is entered and existed a few times.
  • Page 12 Go to “Front Volume Knob” (menu #79 on Aerosmith) For home use games, keep this setting on default so you can use the headphone knob to control the games volume when the headphones are not plugged in. For games on location, set to “HEADPHONES VOL. ONLY”. This setting prevents the customer from adjusting the games volumen.

  • Page 13: Setup Menu Part 2

    Not all Spike 2 machines will have the same menu! The VOL menu is not numbered so it makes it difficult to navigate. Scroll through the VOL menu to become familiar with the menu items. Menu item “ADJUST HEADPHONE VOLUME” is basically the same menu that the PinPAC TH2 volume control adjusts. No need to touch this menu.

  • Page 14: Closing Statements

    We keep our eyes open for useful pinball product ideas we are pinball people too! Warranty and repairs: Pinnovators will stand behind everything we sell. If our product ever fails, contact us and we will make it right! (Even if you didn’t make the original purchase or you break our product) Contact Us:...

This manual is also suitable for:

330.202.00

Table of Contents