Subscribe to Our Youtube Channel
Summary of Contents for Fike FlamQuench II DN200
- Page 1 8.8520.00.0 FlamQuench II VENTING WITH FLAME AND PARTICLE RETENTION INSTALLATION AND OPERATING INSTRUCTIONS...
-
Page 2: Table Of Contents
TABLE OF CONTENTS PAGE # 1. INTRODUCTION......................... 1 2. GENERAL INFORMATION ......................1 DESCRIPTION........................1 SERVICE QUALIFICATIONS ..................... 1 PERSONNEL SAFETY ...................... 1 II SAFETY ....................1 UENCH II INSTALLATION PROCEDURE .............. 1 UENCH II REMOVAL PROCEDURE ..............2 UENCH IDENTIFICATION OF F II... - Page 3 TABLES AND FIGURES PAGE # Table 1 Refurbish Kits ........................4 Table 2 FlamQuench II English Specifications................6 Table 3 FlamQuench II Metric Specifications ................7 Figure 1 Installation Diagram ......................8 Figure 2 Installation Orientation..................... 9 Figure 3 FlamQuench II Specifications..................10 Figure 4 FlamQuench II...
-
Page 4: Introduction
Fike FlamQuench II Fike Corporation has designed and manufactures the FlamQuench II in two versions: an imperial size unit specified according to NA standards, available in size 8” through 40”; and a metric version specified and built for the CE market, available in size DN200 through DN1000. -
Page 5: Flamquench Ii Removal Procedure
• FlamQuench II may be installed anywhere between vertical and horizontal. See Figure 2 (page 9). Fike Corporation shall evaluate any deviation from this orientation. • The FlamQuench II requires sufficient support based on the FlamQuench II weight and reaction force created during activation. -
Page 6: Refurbishment Instructions
REFURBISHMENT INSTRUCTIONS 5.1 FILTER HANDLING WARNING WARNING: To prevent possible injury (cuts & scrapes), wear leather gloves when handling the filters. 5.2 FILTER REPLACEMENT 5.2.1 REMOVE FILTER (Refer to Figures 4 and 5, pages 11 and 12) Step 1: Follow removal procedures in Section 2.6. Step 2: Remove nuts, bolts and washers and discard. -
Page 7: Refurbish Kits
5.3 REFURBISH KITS Each Refurbish Kit contains the following components: • Hardware (nuts, bolts, washers) • Top Inner Filter • Top Outer Filter • Side Filter (s) • Fiber Frax Rings • FlamQuench II Installation and Operation Manual (E06-045) Kit Part Number – English Kit Part Number –... -
Page 8: Scheduled Maintenance
SCHEDULED MAINTENANCE All system components should be thoroughly inspected by factory trained personnel. Following are specific requirements. Additional maintenance may be required depending on process and environmental conditions. 6.1 EVERY THREE (3) MONTHS • Visually inspect the system. • Keep filter free of dust. Use soft brush or vacuum to remove dust from filter. •... - Page 9 Table 2 FlamQuench II English Specifications (Refer to Figure 3) FQ II BOLT TORQUE SIZE (FT-LBS.) 8 1/8 10 5/8 9 ½ 8” 12” 12 3/16 15 3/16 13 13/16 7/16 14 3/16 17 3/16 15 13/16 7/16 14” 16 ¼ 19 ¼...
- Page 10 Table 3 FlamQuench II Metric Specifications (Refer to Figure 3) FQ II BOLT TORQUE SIZE (N-m) DN200 Dn300 33/80** 33/80** DN350 33/80** DN400 DN500 33/80** 33/80** DN600 33/80** DN750 DN800 33/80** 1000 33/80** DN900 1002 1102 1057 33/80** DN1000 NOTE: Flange stud torque values are based on using 1/8"...
- Page 11 Figure 1 Installation Diagram LIFT RING LIFT RING FLAMQUENCH II HARDWARE EXPLOSION VENT LIFT RING ID TAG GASKET BOLTING PAD Page: 8 Manual P/N: 8.8520.00.0 Revision : A – October 15, 2001...
- Page 12 Figure 2 Installation Orientation SUPPORT TO BE EVALUATED CABLE SUPPORT FLAMQUENCH II SHALL BE MOUNTED WITHIN 90° OF VERTICAL Manual P/N: 8.8520.00.0 Page: 9 Revision : A – October 15, 2001...
- Page 13 Figure 3 FlamQuench II Specifications 8” – 40” (DN200 – DN1000) SIZES (Ref. Tables 2 and 3) Page: 10 Manual P/N: 8.8520.00.0 Revision : A – October 15, 2001...
- Page 14 Figure 4 FlamQuench II Assembly Sizes 8” – 20” (DN200 – DN500) TOP FRAME WELDMENT ID TAG TOP OUTER FILTER ID TAG TOP INNER FILTER FIBER FRAX RING SIDE FILTER ID TAG FIBER FRAX RING BOTTOM WELDMENT LOCK WASHER BOLT Manual P/N: 8.8520.00.0 Page: 11 Revision : A –...
- Page 15 Figure 5 FlamQuench II Assembly SIZES 24” – 40” (DN600 – DN1000) TOP FRAME WELDMENT TOP OUTER FILTER ID TAG TOP INNER FILTER ID TAG FIBER FRAX RING SIDE FILTER ID TAG FIBER FRAX RING CENTER RING SUPPORT WELDMENT FIBER FRAX RING BAND SIDE FILTER FIBER FRAX RING...
- Page 16 Figure 6 Filter Installation ID TAG TOP OUTER FILTER ID TAG TOP INNER FILTER BOTTOM WELDMENT FIBER FRAX RING FIBER FRAX RING SIDE FILTER SIDE FILTER FIGURE 6A FIGURE 6B TOP FRAME WELDMENT HARDWARE (STAINLESS) FIGURE 6C Manual P/N: 8.8520.00.0 Page: 13 Revision : A –...
- Page 17 flow & process solutions Potravinářský průmysl Farmaceutický průmysl Biotechnologie Petrochemie Chemický průmysl Energetika Úprava vody Papírenství a zpracování celulózy Plynárenský průmysl Keramický průmysl Zpracovatelský průmysl Firma s tradicí od r. 1990 se při svém vzniku zaměřila na dodávky základních komponent, přístrojové a měřící techniky a dodávky technologií pro farmaceutický...
- Page 18 REGOM INSTRUMENTS s.r.o. Brabcova 1159 / 2 147 00 Praha 4 CZECH REPUBLIC Tel: +420 241 402 206 Fax: +420 241 400 290 Mail: regom@regom.cz Skype: regom-office www.regom.cz...
Need help?
Do you have a question about the FlamQuench II DN200 and is the answer not in the manual?
Questions and answers