Disconnection ..........................................18 10 Troubleshooting ..........................................18 Revision history Date Revision 2022-01-28 PN: PD10010, Copyright Ferroamp Elektronik AB 2022. Document subject to change without prior notice. Verify that you have the latest version of this manual on our website. www.ferroamp.com/downloads...
Färdigmonterat Pylontech M1 I detta häfte finner du anvisningar för installation av ert Mått (H x B x D): 2130 x 815 x 659 mm Pylontech M1-batteri. Se till att läsa instruktionen noggrant för Vikt: 1036 kg att undvika onödiga fel.
• Se till att placeringen av Pylontech M1 aldrig utgör ett hinder för nödutrymning, i enlighet med nationell och lokal lagstiftning. 1. Avlägsna de tre översta planen i den högra halvan av rackskåpet.
Inkoppling av batterimoduler 1. Placera Pylontech SC100 Controller i facket längst upp till vänster i rackskåpet enligt bilden (bortse från kablarna). Fäst med avsedda skruvar i fästskenor. 3. Dra DC-kabel typ D och DC-kabel typ E ut genom den vänstra öppningen i toppen av rackskåpet och för sedan in kabeln genom den högra öppningen.
Page 6
3. Koppla samman batterimoduler på vänster halva av rackskåpet med DC-kablar typ A. 4. Koppla samma batterimoduler med kommunikationskablar enligt bilden ovan. 7. Koppla samman övriga batterimoduler på högra halvan av rackskåpet med DC-kablar typ A enligt bilden ovan. 8. Koppla samman övriga batterimoduler på högra halvan av rackskåpet med kommunikationskablar enligt bilden ovan.
Page 7
10. Anslut DC-kabel typ D i kontakten DC+ och DC-kabel typ E i kontakten DC- enligt bilden ovan. 11. Koppla samman den översta batterimodulen och Pylontech kontrollmodul med en kommunikationskabel enligt bilden ovan 12. Anslut CAN-kommunikationskabel ESO - kontrollmodul i CAN/Link port B enligt bilden ovan 13.
Page 8
17. Säkerställ att DC-nätet är spänningslöst samt att Pylontech SC100 Controller är avstängd. Anslut sedan DC-kabel typ D och DC- 19. Anslut ESO 2 till en adapter utan Pre Charge-kabel. Koppla kabel typ E samt DC-kabel till DC-nät till respektive kopplingsplint sedan samman ESO 1 och ESO 2 med en ethernetkabel enligt enligt bilden ovan.
Page 9
21. Säkerställ att alla DIP-switchar på baksidan av ESO:erna står i rätt läge och placera sedan ESO:er enligt bilden ovan. 23. Drag ut ESO:erna cirka 5cm ur skåpet och montera sedan frontplåten enligt bilden ovan. 24. Placera ESO:erna så att frontplåten ligger mot listerna på rackskåpet och fäst sedan frontplåten i de förberedda korgmuttrarna.
4 Urkoppling Vid urkoppling av ett Pylontech M1 se till att följande steg efterföljs: Stäng av likspänningsnätet samt öppna brytaren i den DC-fördelningen som batteriet är anslutet till. Slå av Pylontech Kontrollmodulen genom att trycka på den röda knappen. Koppla ur AC-kabeln ur 230V vägguttag Koppla bort Kontrollmodulen från ESO-distributionen...
Included items Dimensions (H x W x D): 150.5 x 330 x 628 mm Weight: 48 kg The following items are included in the delivery of a Pylontech M1: Article Quantity Warnings and reservations Pylontech M1 cabinet...
• Ensure that the Pylontech M1 placement never becomes an obstacle to a emergency evacuation path. 1. Remove the top three shelfs in the right half of the cabinet.
Installation of battery modules 1. Place the Pylontech SC100 Controller in the compartment at the top left of the cabinet as shown (disregard the cables). Fasten with the intended screws in the mounting rails. 3. Route DC cable type D and DC cable type E through the left opening in the top of the cabinet and then insert the cable through the right opening.
Page 15
3. Connect battery modules on the left half of the rack cabinet with DC A type cables as shown above. 4. Connect battery modules with communication cables as shown above. 7. Connect the battery modules on the right half of the cabinet with DC cables type A as shown above.
Page 16
10. Connect DC cable type D to the DC + connector and DC cable type E to the DC- connector as shown above. 11. Connect the top battery module and the Pylontech control module with a communication cable as shown above 12.
Page 17
17. Make sure that the DC network is de-energized and that the Pylontech SC100 Controller is switched off. DC cable type D and 19. Connect ESO 2 to an adapter without a Pre Charge cable. Then DC cable type E and the DC cable to the EnergyHub in the terminal connect ESO 1 and ESO 2 with an Ethernet cable as shown above.
Page 18
21. Make sure that all DIP switches on the back of the ESOs are in the correct position and then place the ESOs as shown above. 23. Pull the ESOs about 5 cm out of the cabinet and then mount the ESO front plate as shown above. 24.
9 Disconnection When disconnecting a Pylontech M1, make sure that the following steps are followed: Switch off the mains supply and open the switch in the DC distribution to which the battery is connected. Switch off the Pylontech Control Module by pressing the red button.
Need help?
Do you have a question about the Pylontech M1 and is the answer not in the manual?
Questions and answers