ZIGBEE ROB 200-035-0 Quick Start Manual

16A ZigBee In-wall Switch
Important: Read All Instructions Prior to Installation
Function introduction
Switch input
Zigbee In-Wall Switch
"Reset" Key: for
network pairing,
touchlink, factory
reset of the switch
1 CH load output
Product Data
Input Voltage Output Voltage
100-240VAC 100-240VAC
Compatible Load Types
Load Symbol Load Type
LED lamps with transformers
LED drivers
Incandescent lighting,
HV Halogen lamps
Low voltage halogen
lighting with electronic
transformers
Electrical appliances
such as television,
refrigerator, water
heating etc.
Over Current Protection
• When load current is over 16.1A for over 10 seconds, the relay will be forced to off and protected.
• When load power is over 3700W for over 5 seconds, the relay will be forced to off and protected.
09.ZG09SAPB.04736
LED indicator: stays off if the device
is not added to a Zigbee network,
stays solid on after the device is
added to a network. Same indication
as connected load when commissioning
the device: network pairing, touchlink,
factory reset
AC 100-240V power input
Output Current Size(LxWxH)
16A max 45.5x45x20.3mm
Maximum Load Remarks
Due to variety of LED lamp
designs, maximum number
1220W @ 230V of LED lamps is further
580W @ 110V dependent on power factor
result when connected to
switch.
Maximum permitted number
1220W @ 230V
of drivers is 1220W divided
580W @ 110V
by driver nameplate power
rating.
3680W @ 230V
1760W @ 110V
1220W @ 230V
580W @ 110V
3680W @ 230V
1760W @ 110V
• ZigBee in-wall switch based on latest ZigBee 3.0 protocol
• 100-240VAC wide input and output voltage
• Supports resistive loads and capacitive loads
• 1 channel output, max. load 16A
• Input and output with screw terminals, safe and reliable
• Enables to control ON/OFF of connected load
• ZigBee end device that supports Touchlink commissioning
• Can directly pair to a compatible ZigBee remote via Touchlink without coordinator
• Supports self-forming zigbee network without coordinator and add other devices to the network
• Supports find and bind mode to bind a ZigBee remote
• Supports zigbee green power and can bind max. 20 zigbee green power switches
• Compatible with universal ZigBee gateway products
• Can be controlled by toggle on/off switches
• Active power and energy metering functionality
• Mini size, easy to be installed into a standard size wall box
• Radio frequency : 2.4GHz
• Waterproof grade: IP20
Safety & Warnings
• DO NOT install with power applied to device.
• DO NOT expose the device to moisture.
ZigBee Clusters the device supports are as follows:
Input Clusters
• 0x0000: Basic • 0x0003: Identify • 0x0004: Groups
• 0x0702: Simple Metering • 0x0b04: Electrical Measurement
Output Clusters
• 0x0019: OTA
Operation
1.Do wiring according to connection diagram correctly.
2.This ZigBee device is a wireless receiver that communicates with a variety of ZigBee compatible systems. This
receiver receives and is controlled by wireless radio signals from the compatible ZigBee system.
3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)
Step 1: Remove the device from previous zigbee network if it has already been added to, otherwise pairing will
fail. Please refer to the part "Factory Reset Manually".
Step 2: From your ZigBee Controller or hub interface, choose to add lighting device and enter Pairing mode as
instructed by the controller.
Step 4: Connected light will blink 5
times and then stay solid on, then the
device will appear in your controller's
menu and can be controlled through
controller or hub interface.
• 0x0005: Scenes • 0x0006: On/off
• 0x0b05: Diagnostics
Zigbee In-Wall Switch
Step 3: Reset power of the device from
master breaker to set it into network
pairing mode (connected light flashes
twice slowly), the network pairing mode
will last until the device is added to a
zigbee network.
L
N