1. Manuals
  2. Brands
  3. Greenbroz Manuals
  4. Industrial Equipment
  5. M+
  6. User manual

Greenbroz M+ User Manual

Trimming system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
M+ TRIMMING SYSTEM
User Manual
GreenBroz.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M+ and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Greenbroz M+

Summary of Contents for Greenbroz M+

  • Page 1 M+ TRIMMING SYSTEM User Manual GreenBroz.com...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS System Weight/Diminutions/Power ....................3 System Use/Safety .........................3 PART 1: Rise Conveyor..................... 4 Machine Parts Identifier....................5 Unpacking and Installation..................6 Hopper Installation...................6 Belt Installation....................8 Belt Tensioning .....................12 Primary Wall Installation .................13 Control Box Installation ..................15 Operation and Shutdown ..................16 Cleaning and Sanitation....................19 Troubleshooting ......................20 PART 2: Model M +...

  • Page 3: System Weight/Diminutions/Power

    Before clearing the blockage, disconnect power from both machines (if the doors were in the open state, wait for the doors to close). Once power has been disconnected, investigate, clear the blockage, and resume operation. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 4: Part 1: Rise Conveyor

    PART 1: RISE CONVEYOR...

  • Page 5: Machine Parts Identifier

    110VAC, 60Hz 3A 330W (US) • Conform to UL508 (ISBN 0-7629-0404-6) machine safety for use in pollution degree Power: 220VAC, 50Hz 1.5A 330W (International) 2 environment • Relative humidity (10%-90%) ° ° ° ° • 32 F-104 F ( 0 C-40 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 6: Unpacking And Installation

    4. Ensure the Master Power Switch is in the off position and plug the cord into the machine. HOPPER INSTALLATION 1. Install the Lower Side Walls by first inserting the Hook Bracket into the lower cutout on the rear Hopper Cradle. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 7 4. Slide the Hopper Brackets into the two rear Hopper Cradles (Note: Make sure the Lower Side Wall Hook is outside of the Lower Side Wall). 5. Insert the two upper Hopper Hooks into the slots provided in the Lower Side Walls. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 8: Belt Installation

    Continue pulling the Belt up to the top of the machine. Tip: The Belt may slide back down. Use the Drive Gears (shown in step three) to hold the belt in place. This can be done with or without the Hopper installed. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 9 Take the end of the Belt and run it through the rear Toggle Guides (1) and on top of the Bottom Guides (2). Make sure to keep the Belt inside of the Flanges of the frame (3). 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 10 The Belt will go above the Small Rollers (1), below the Motor (2), in between the Top Chain Guards (3), and around the Drive Gears (4). Again, make sure to keep the Belt above the Flanges of the frame (5). 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 11 Pin (2) through the penetrations (3) in each of the Laces. It is critical that the Pin is pushed all the way through and all Laces are secured properly. The orientation of the Pin is not critical. It can be put into either side of the Belt. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 12: Belt Tensioning

    Bearing (2) attached to the tensioning Bolt (3), the Belt can be finely adjusted. A new Belt should have theTensioning Screws fully threaded into the Toggle Clamp. This gives the Belt plenty of tension (DO NOT OVER TIGHTEN - shown extended for clarification). 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 13: Primary Wall Installation

    1. The Primary Walls easily slide directly into the slots on the Main Frame of the Rise Conveyor. The short F-Brackets (1) slide into the top primary slots (2), and the long F-Bracket (3) slides into the bottom primary slot (4), as shown. The F-brackets should be facing away from the machine. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 14 PRIMARY WALL INSTALLATION PRIMARY WALL INSTALLATION 2. The Primary Walls (1) should be pushed all the way down flush with the Belt (2) 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 15: Control Box Installation

    Rise Conveyor (3). b. The yellow Four-Prong Connection (4) screws into the machine’s Electrical Supply (5). The Third Connection on the back of the Control Box is for the Foot Pedal Control. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 16: Operation And Shutdown

    15 seconds for the Touch Screen to completely start up. If the Control Box does not immediately power up upon plugging it into the Wall, the Emergency Stop may be activated. Rotate the Emergency Stop clockwise to release it and give power back to the machine. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 17 Touch the screen anywhere to get to the home page. From this page you can get to the machine controls (start feeding button), view the run time of the machine (settings button), or find GreenBroz contact information (help button). Start Feeding Screen: •...
  • Page 18 • The Belt has not been properly installed on the machine and is causing gear slipping or Motor ceasing. • The Hopper and Belt are colliding at the base where the Belt enters the Hopper, this would be from improper installation of the Belt or Hopper. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 19: Cleaning And Sanitation

    The Belt is a thermoplastic elastomer manufactured by Midwest Industrial Rubber, Inc. Please see reference 1 at the end of this user manual for specific information regarding cleaning and sanitizing your Rise Conveyor’s Belt. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 20: Troubleshooting

    It is recommended to only do one rotation of the Toggle Bearing at a time and restart the machine to remedy the walking issue. The below example shows a Belt walking to the left and how to adjust using the Toggle Bearing. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 21 If the slipping is still occurring, extend the Toggle Bolts one full rotation at a time, then retry starting the machine. It is critical that the user extend the Toggle Clamps equally, or unnecessary wear may occur. Any other issues, comments, or complaints can be submitted to service@greenboz.com. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 22: Part 2: Model M

    PART 2: M+ TRIMMER...

  • Page 23: Machine Parts Identifier

    9. Stainless Steel Stand 10. Lower Flower Fin 11. Upper Flower Fin 12. Hub Key + Hub Screw (13) 1. Flower Ramp 13. Wedge Bracket 2. Top Blade 14. Emergency Stop 3. Bottom Blade 15. Touch Screen 4. Removable Barrel 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 24: Unpacking

    Toggle between forward and reverse to get the last bit out. 7. Finally press the DOOR button once again to close the Doors. NOTE: Keep hands away from doors when opening and closing. 8. Repeat until your harvest is complete. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 25: Close-Ups/Shutdown/Cleaning

    CLOSE-UPS | SHUT DOWN | CLEANING CLOSE-UPS | SHUT DOWN | CLEANING CLOSE UPS Convenient hooks on both sides for Blade and Terrel Storage Upper and Lower Fin Assembly Cap Connectors when you pressure wash. Auto Door 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 26 9. Wipe down all surfaces with alcohol and lint free cloth. *** If you are going to pressure wash your machine, remove the Control Box, and cap power connections. SCAN QR Code to see the How To Clean Your Model M video 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 27: Door Removal/Calibration

    Door Drive Shaft is engaged with the Motor by giving the Door a light twist. You should feel the Motor resisting the motion. 2. Repeat on the other side with the other Door. 3. Rotate both Plastic Swivel Door Locators inward toward the Doors to lock them in place. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 28 5. Re-install the Door(s), Barrel, and Blades and continue trimming! Note: each Door and Drive Shaft is unique, do not switch the shafts or doors - however the Door Indexing Jig works on both sides. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 29: Product Prep And Troubleshooting

    (not bend) when you run your finger down the bud. *We recommend lowering the humidity on the last day of the drying cycle in order to crisp them leaves while keeping the bud spongy and moist. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 30 Check Fuse F2 (110V/220V to Motor Driver) on Safety Card. (2) Spare Fuses are attached to inside of Door. Check IO cable is connected to Motor Driver. Check IO cable is connected to Touchscreen. Connect IO cable to Motor Driver / Touchscreen 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 31 Check Rise Conveyor is connected with ethernet cable. Connect ethernet cable. Check ethernet cable for damage. Check Rise Conveyor has power available. 110VAC 60Hz for US Version 220VAC 50Hz for UK Version Any other issues, comments, or complaints can be service@greenboz.com. submitted to 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 32: Part 3: M+ Trimming System

    PART 3: M+ TRIMMING SYSTEM...

  • Page 33: Maintenance And Cleaning

    Motor Drive Shaft Hole in the Motor Mount Casters Check Casters for damage, ensure they roll Weekly smoothly. If there is any damage to the Casters that prevent them from operating normally, replace them. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 34 Rise Conveyor are built with an IP 66 rating meaning they can be pressure washed with high pressure (using a 12.5 mm nozzle, 100 kPa at distance of 3 m). Before pressure washing the machines, make sure to remove both control boxes and cap any connections. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 35: Automation

    The ethernet cable connects the two Power Boxes together. Make sure both machines are off when plugging in the ethernet cable. 3. Once the Power Boxes are connected, the Model M+ Box will control both machines. The Rise Conveyor Box will simply display the current operation and a cycle count. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 36 Help: gives you information about contacting our Service Department Settings: gives you access to the driver settings and allows use of classic mode Start Trimming: takes you to the run screen SCAN QR Code to see the How To Operate M+ System 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 37: Recipe Creation/Storage

    Deletes the selected recipe (not the active recipe) Takes you to the setup page to make changes to the recipe 10. Takes you to the Auto Run page so you can run the recipe 11. Takes you to the Home Page 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 38 5. Now we will go through programming the new recipe. Tap the ‘Setup’ button to take you to the next screen. 6. This screen will allow you to program every part of the cycle individually. Rise Speed setpoint (1-100%) controls how fast the Rise Conveyor runs at. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 39 Your total trim time and total load time are displayed to the side of this page. You can also set your Trimmer Speed (1-100%) for each sequence from this page. 11.Press the 'Unload Settings' button to adjust your unload cycle's length and blade direction. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 40 16. And finally, to delete a recipe simply select the recipe you want to delete and tap ‘Delete’. 17. Press 'Home' to return to the home screen. Help 1. The Help screen displays GreenBroz' contact info and operating hours. 2. Press 'Home' to return to the home screen. 844.DRY.TRIM info@greenbroz.com...
  • Page 41 2. The 'Classic Mode' button will take you to the classic manual screen for machine operation. 3. This screen is the classic run screen and allows you to run the Trimmer in manual mode. This screen does not control the Rise Conveyor in any way. 844.DRY.TRIM info@greenbroz.com greenbroz.com...
  • Page 42 6. From this page or the Auto Mode page you can go to the Recipe creation screen or the Home screen by tapping ‘Recipe’ or ‘Home’. 844.DRY.TRIM info@greenbroz.com greenbroz.com...

  • Page 43: Warranty Registration

    To Qualify for this warranty: The product must be purchased from GreenBroz, Inc., or a dealer authorized by GreenBroz, Inc., to sell the products. This warranty only applies to the first retail purchaser and is not transferable to subsequent owners.

Table of Contents