1. Manuals
  2. Brands
  3. unbranded Manuals
  4. Motherboard
  5. ENDAT-5701
  6. User manual

unbranded ENDAT-5701 User Manual

All-in-one motherboards
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ENDAT-5701/5901
All-In-One motherboard
User's Manual
Rev. 2x
For 5701 PCB ver.1F or later
For 5901 PCB ver.2xor later

Advertisement

Table of Contents
loading

Summary of Contents for unbranded ENDAT-5701

  • Page 1 ENDAT-5701/5901 All-In-One motherboard User’s Manual Rev. 2x For 5701 PCB ver.1F or later For 5901 PCB ver.2xor later...
  • Page 2 The ENDAT-5701/5901 All-In-One motherboard Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to the this document and/or the product at any time without prior notice.
  • Page 3 User’s Manual Specification: ENDAT-5701 ENDAT-5901 MODEL Pentium 75-550MHz, INTEL MMX, AMD K5/K6/K6-2/K6-3, IDT C6, Rise MP6, IBM Cyrix 6x86 CPU System Chipset VIAChipset VGA Chipset Built-in, With Share Memory Architecture LCD Feature (Optional) Optional Support TFT/ DSTN LCD LAN Chipset...
  • Page 4 The ENDAT-5701/5901 All-In-One motherboard...

  • Page 5: Table Of Contents

    CHAPTER 1. INTRODUCTION..........1 1-1. FEATURES ......................1 1-2. UNPACKING..................... 3 1-3. ELECTROSTATIC DISCHARGE PRECAUTIONS ......... 3 1-4. MOTHERBOARD LAYOUT (ENDAT-5701) ..........4 1-5. MOTHERBOARD LAYOUT (ENDAT-5901) ..........5 CHAPTER 2. SETTING UP THE MOTHERBOARD..... 6 2-1. JUMPERS AND CONNECTORS (ENDAT-5701)........6 2-2.
  • Page 6 The ENDAT-5701/5901 All-In-One motherboard 4-3. PCI BUS AUDIO ADAPTER FEATURE............44 4-4. DISKONCHIP FEATURE................45 4-5. DRIVER UTILITY INSTALLATION GUIDE ..........46 CHPATER 5. LAN ADAPTER..........48 5-1. FEATURES ......................48 5-2. UTP CABLE/RJ-45 JACK DEFINITION............49 5-3. CONNECTING 100BASE-TX FAST ETHERNET NETWORK....50 5-4. CONNECTING 10BASE-T ETHERNET NETWORK......50 5-5.

  • Page 7: Chapter 1. Introduction

    -in VGA onboard supports TFT/DSTN Flat Panel and Audio, built -in Realtek 8139xx LAN chipset with RJ45 Jack for 10BaseT/100BaseT. Our board offers the highest performance PC specifications in the industry. The ENDAT-5701 and ENDAT-5901 runs with the Intel Pentium P54C/P55C, AMD K5/K6, K6-2/K6-3, IDT C6, Rise MP6 or IBM/Cyrix 6x86 CPU upto 550MHz.
  • Page 8 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses • P C I-2.2 compliant, 32 bit 3.3V PCI interface with 5V tolerant inputs • Onboard socket for DiskOnChip supports M -System products • Onboard LAN Adapter supports 10BaseT/100BaseT, (On board) BOOT ROM optional •...

  • Page 9: Unpacking

    User’s Manual 1-2. Unpacking The motherboard comes securely packaged in a sturdy cardboard shipping carton. In addition to the User's Manual, the motherboard package includes the following items: • ENDAT-5701/ENDAT-5901 All-In-One Motherboard • HDC/FDC Cables • TV-Out Cable (Optional) •...

  • Page 10: Motherboard Layout (Endat-5701)

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 1-4. Motherboard Layout (ENDAT-5701)

  • Page 11: Motherboard Layout (Endat-5901)

    User’s Manual 1-5. Motherboard Layout (ENDAT-5901)

  • Page 12: Chapter 2. Setting Up The Motherboard

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Chapter 2. Setting up the Motherboard This chapter describes how to set up the motherboard and get ready for operation. • Installing the CPU upgrade • Installing DIMM memory. Make sure the correct CPU operating voltage, jumper settings and frequency.
  • Page 13 User’s Manual Function Jumpers/Connectors RS232/RS422/RS485 Selector (COM2) JP7, JP8, JP9, JP10 TTL Output Pin Header (For COM2) TTLOut1 Touch Panel Pin Header Touch1 DiskOnChip Memory Address LCD Connector LCD_CON1 Clear CMOS PS/2 Keyboard Jack PS/2 Mouse Jack PS/2 Mouse/KB Pin Header USB Header CN11 FDD Connector...
  • Page 14 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses ENDAT-5701 CPU Vcore Setting: Switch2 (S2: SW1-SW5) VCORE=3.5V VCORE=3.4V S1 S2 S3 S4 S5 S1 S2 S3 S4 S5 ON ON ON ON OFF OFF ON ON ON OFF VCORE=3.3V VCORE=3.2V S1 S2 S3 S4 S5...
  • Page 15 Please make sure the CPU Vcore voltage and setting as mention above for your system. The wrong setting may cause system damaged the CPU or system not working. For ENDAT-5901 Rev.1D or later. For ENDAT-5701 Rev.1F or later. ENDAT-5701 CPU Ratio Setting: Switch2(S2:SW6-SW8) S2 = 2.5x S2 = 3.0x S2 = 2.0x / 6.0x...
  • Page 16 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses ENDAT-5701 CPU CLOCK Setting: Switch1(S1:SW1-SW4) CPU = 60MHz CPU = 66.8MHz PCI CLK=30MHz PCI CLK=33.4MHz OFF OFF OFF OFF ON OFF OFF OFF CPU = 68.5MHz CPU = 75MHz PCI CLK=35MHz PCI CLK=37.5MHz OFF ON OFF OFF...
  • Page 17 User’s Manual JP1: CMOS Data Clear: Pin 1-2 * Normal Pin 2-3 Clear CMOS Data JP2: DiskOnChip Memory Address Selector Memory Address 0C800H-0C9FFH 9-10 0CC00H-0CDFFH 0DCCCH-0D1FFH 9-10 0D400H-0D5FFH 0D800H-0D9FFH(Default) JP4: On-board LAN Disable/Enable Pin 1-2 * Enable On-Board LAN Pin 2-3 Disable On-Board LAN JP6 (COM1) / JP12 (COM3) / JP13 (COM4) Voltage Selector: Pin No.
  • Page 18 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses FAN1, FAN2: CPU / 2nd Cooling Fan Connector Pin No. Function Pin 1 Sensor Pin. Pin 2 +12V Pin 3 J3’s Pin15;16;19;20;21: For ATX Power Supply Close Pin 19-20 Using PS/2 AT Power Supply...
  • Page 19 User’s Manual LCD_CON1 (Only for Support LCD Version) Pin No. Description Pin No. Description VDDLCD(+3.3V) VDDLCD(+3.3V) ENPVEE FPD23 FPD22 FPD17 FPD16 FPD11 FPD10 FPD9 FPD8 FPD21 FPD20 FPD15 FPD14 FDP7 FPD6 FPD5 FPD4 FPD19 FPD 18 FPD13 FPD12 FPD3 FPD2 FPD1 FPD0 SHFCLK...
  • Page 20 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 18Bit TFT DSTN / 16Bit DSTN LCD Panel Mapping 18Bit 16Bit 18Bit / 18+18 Pin No. DSTN N.C. FPD23 FPD22 FPD21 N.C. FPD20 FPD19 FPD18 FPD17 FPD16 FPD15 FPD14 FPD13 FPD12 FPD11 FPD10 FPD9...

  • Page 21: Jumpers And Connectors (Endat-5901)

    User’s Manual 2-2. Jumpers and Connectors (ENDAT-5901) Function Jumpers/Connectors CPU: CPU Clock Frequency Switch 1 (S1: SW1-SW4) CPU Ratio Switch 2 (S2: SW6-SW8) CPU Vcore Voltage Switch 2 (S2: SW1-SW5) Connector for Cooling Fan FAN1; FAN2 Power Supply: Type (ATX or PS/2) CN7(ATX) ;...
  • Page 22 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Function Jumpers/Connectors IDE 2 Connector FDD Connector Header for Case Panel IDE 1 LED J4 Pin 1, Pin 2 IDE 2 LED J4 Pin 3, Pin 4 External Speaker J4 Pin 5, Pin 8...
  • Page 23 User’s Manual ENDAT-5901 CPU Vcore Setting: Switch 2 (S2: SW1-SW5) VCORE=3.5V VCORE=3.4V S1 S2 S3 S4 S5 S1 S2 S3 S4 S5 ON ON ON ON OFF OFF ON ON ON OFF VCORE=3.3V VCORE=3.2V S1 S2 S3 S4 S5 S1 S2 S3 S4 S5 ON OFF ON ON OFF OFF OFF ON ON OFF VCORE=3.1V...
  • Page 24 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses above for your system. The wrong setting may cause CPU damage or system not working. For ENDAT-5901 Rev.1D or later. For ENDAT-5701 Rev.1F or later. ENDAT-5901 CPU Ratio Setting: Switch2 (S2:SW6-SW8) S2 = 2.5x S2 = 3.0x...
  • Page 25 User’s Manual ENDAT-5901 CPU CLOCK Setting: Switch1(S1:SW1-SW4) CPU = 60MHz CPU = 66.8MHz PCI CLK=30MHz PCI CLK=33.4MHz OFF OFF OFF OFF OFF OFF OFF CPU = 68.5MHz CPU = 75MHz PCI CLK=35MHz PCI CLK=37.5MHz OFF ON OFF OFF OFF OFF OFF ON CPU = 97MHz CPU = 83.3MHz PCI LK=26.67MHz...
  • Page 26 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses JP1, JP2, JP3, JP4: RS232 / 422 / 485 Selector for COM2 RS-232* Open 1-2, 4-5, 7-8, 9-10 Open RS-422 Close 2-3, 5-6, 8-9, 11-12 1-2, 4-5 RS-485 Close 2-3, 5-6, 8-9, 11-12 2-3, 5-6 Make sure the port mode is set up correctly before installing any peripherals.
  • Page 27 User’s Manual FAN1, FAN2: CPU / 2ND Cooling Fan Connector Pin No. Function Sensor Pin. +12V CN10: Audio Output Port connector via AV Card Kit (Optional) The AV Card Kit Adapter supports Sound, TV-OUT, S-Video and Game Port. Please close pin13-14 to disable onboard Audio features if the AV Card Kit is not inserted onto the CN10...
  • Page 28 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses LCD_CON1 (Only for Support LCD Version) Pin No. Description Pin No. Description VDDLCD(+3.3V) VDDLCD(+3.3V) ENPVEE FPD23 FPD22 FPD17 FPD16 FPD11 FPD10 FPD9 FPD8 FPD21 FPD20 FPD15 FPD14 FDP7 FPD6 FPD5 FPD4 FPD19 FPD 18...
  • Page 29 User’s Manual 18Bit TFT / 16Bit DSTN LCD Panel Mapping 18Bit 16Bit 18Bit / 18+18 Pin No. DSTN N.C. FPD23 N.C. FPD22 N.C. FPD21 N.C. FPD20 N.C. FPD19 N.C. FPD18 N.C. FPD17 N.C. FPD16 FPD15 FPD14 FPD13 FPD12 FPD11 FPD10 FPD9 FPD8 FPD7...

  • Page 30: Installing Memory

    D,A,B,C AD21 There are two different riser cards that can be fitted to ENDAT-5701/ENDAT -5901 All-In-One motherboard. The first one is a 98pin ISA only Bus riser card (traditional ISA Bus riser card), the second one is a 188pin PCI/ISA riser card.

  • Page 31: Assigning Irqs For Expansion Cards

    User’s Manual 2-6. Assigning IRQs for Expansion Cards Some expansion cards require an IRQ (Interrupt request vector) to operate. Generally, each IRQ must be exclusively assigned to specific use. In a standard design, there are 16 IRQ available with 11 of them already in used by other part of the system.

  • Page 32: Assigning Dma Channels For Isa Cards

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Status Assignment Used Floppy Disk Used LPT1 Used Used Redirected IRQ2 / SoundBlaster Used COM4 (Optional) Used LAN Adapter (on board) Used PS/2 Mouse Used Coprocessor Used Hard Disk (IDE 1) Used Reserved (IDE 2) 2-7.

  • Page 33: Chapter 3. Award Bios Setup

    User’s Manual Chapter 3. AWARD BIOS SETUP Use the CMOS setup program to modify the system parameters to reflect the environment installed in your system and to customize the system as desired. Press the <DEL> key to enter into the CMOS setup program when you turn on the power. Settings can be accessed via arrow keys.

  • Page 34: Bios Features Setup

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 3-2. Description of the BIOS Setup Option Please make clear the means of those option parameters. Improper settings will cause the system to hang up or perform poorly. Most items are clearly understood from the screen prompt. The manufacturer highly recommends that “Default”...

  • Page 35: Details Of Chipset Feature Setup

    User’s Manual 3-4. Details of the Chipset Feature Setup ROM PCI/ISA BIOS (2A5LHU4A) CHIPSET FEATURE SETUP AWARD SOFTWARE, INC Bank 0/1 DRAM Timing : SDRAM 8/10ns Bank 2/3 DRAM Timing : SDRAM 8/10ns SDRAM Cycle Length DRAM Read Pipeline : Enabled Sustained 3T Write : Enabled Cache R/CPU W Pipeline...
  • Page 36 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Cache R/CPU W Pipeline This item allows you to enable or disable the cache timing. Video BIOS Cacheable When enabled, the Video BIOS cache will cause access to video BIOS addressed at C0000H to C7FFFH to be cached, if the cache controller is also enabled.

  • Page 37: Details Of Power Management Setup

    User’s Manual 3-5. Details of Power Management Setup ROM PCI/ISA BIOS (2A5LHU4A) POWER MANAGEMENT SETUP AWARD SOFTWARE, INC ACPI Function : Disabled Primary INTR : ON Power Management : User Define IRQ3 (COM2) : Primary PM Control by APM : Yes IRQ4 (COM1) : Primary Video Off Method...
  • Page 38 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Max. Power Saving Maximum power management – Only Available for SL CPU’s. Doze Mode = 1 min., Standby Mode = 1 min., Suspend Mode = 1 min., And HDD power down = 1 min.
  • Page 39 User’s Manual HDD Power Down When enabled and after the “Set time of system inactivity”, the hard disk drive will be powered down while all other devices remain active. Doze Mode When enabled and after the “Set time system inactivity”, the CPU clock will run at a slower speed while all other devices operate at full speed.

  • Page 40: Pci Configuration Setup

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 3-6. PCI Configuration Setup This section describes the configuration of the PCI bus system. PCI is a system that allows I/O device to operate at speeds nearing the speed of the CPU itself, when communicating with its own special components.
  • Page 41 User’s Manual Reset Configuration Data Normally, you can leave this field Disabled. If you have installed new add -on device and the system configuration has caused a serious conflict that the operating system cannot boot, then, select enabled to reset Extended System Configuration Data (ESCD) when exit setup.

  • Page 42: System Environment

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 3-7. System Environment Provide some information such as CPU temperature, speed of cooling fan and usage voltage of CPU for user. 3-8. Integrated Peripherals ROM PCI/ISA BIOS (2A5LHU4A) INTEGRATED PERIPHERALS AWARD SOFTWARE, INC OnChip IDE Channel 0...
  • Page 43 User’s Manual IDE Prefetch Mode Enable pre-fetch for IDE drive interface that supports its faster drive access. If disk drive errors appear, change the setting to omit the drive interface where the errors occur. Depending on the configuration of IDE subsystem, this field may not appear, and does not appear when the Internal PCI/IDE field is “Disabled”.
  • Page 44 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses UART 2 Mode This item allows determining which Infrared (IR) function of onboard I/O chip. Onboard Parallel Port This item allows determining the I/O address of onboard parallel port. Onboard Parallel Mode Select an operating mode for the onboard parallel port. Normal EPP (Extended Parallel Port), ECP (Extended Capabilities Port) ECP+EPP PC AT parallel port Bi-directional port Fast, buffered port Fast, buffered and Bi-directional port.

  • Page 45: Agp-Bus Vga Feature

    User’s Manual Chapter 4. VGA, LCD, DOC, IDE Feature 4-1. AGP-BUS VGA Feature The on-board built-in Graphic Controller is a highly integrated display control device that incorporates a 64-bit 3D/2Dgraphic engine and video accelerator with advanced DVD video and optional TV out capability. It provides a flexible and high performance solution for graphics and video playback acceleration for various color depth and resolution modes.
  • Page 46 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses DVD-video playback. The dual video playback is capable of overlaying windows for videoconferencing and multimedia displays. By using an extended 16-bit capture / ZV port the onboard VGA controller can support DTV resolution. This port can operate as either an input for video capture or as an output for video display.

  • Page 47: Lcd Flat Panel Feature

    User’s Manual 4-2. LCD Flat Panel Feature The on-board flat panel interface is designed to support industry standard TFT and DSTN panels. The Flat Panel interface can also be used to drive external LVDS or PanelLink™ transmitters. The high performance VGA Controller provides full hardware level VGA compatibility.

  • Page 48: Pci Bus Audio Adapter Feature

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 4-3. PCI Bus Audio Adapter Features The Chipset built-in SoundBlaster Pro Hardware and Direct Sound Ready AC97 Digital Audio Controller • Dual full-duplex direct sound channels between system memory and AC97 link • PCI Master interface with scatter / gather and bursting capability •...

  • Page 49: Diskonchip Feature

    User’s Manual 4-4. DiskOnChip Feature On board reserved is a 32-pin Socket for DiskOnChip 2000, it is a unique data storage solution to offer a better, faster and more cost effective Flash Disk for applications. The DiskOnChip 2000 provides a Flash Disk (as BIOS expansion) that does not require any additional bus, slot or connector.

  • Page 50: Driver Utility Installation Guide

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 4-5. Driver Utility Installation Guide The directory of driver utilities on the CD-ROM: For System chipset : "4in1" Audio Drivers : "686audio" AGP VGA Drivers : "Mvp4" PCI IDE / UDMA Drivers :"4in1" LAN Drivers : "Rtl8139"...
  • Page 51 User’s Manual LAN Driver: Install the LAN driver for on-board LAN adapter. Please refer to Realtek 8139 LAN Driver Installation Procedure. Chapter 5-9 the VGA Driver: Install the VGA driver for on-board AGP VGA adapter www.via.com.tw Please download or check from VIA Web-site: if you prefer to install the drivers individually or you need more information.

  • Page 52: Features

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Chapter 5. LAN Adapter The on-board LAN adapter use of Single Chip Fast Ethernet Controller, that is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory.

  • Page 53: Utp Cable/Rj-45 Jack Definition

    User’s Manual 5-2. UTP Cable / RJ-45 Jack Definition Straight through twisted pair cable is typically used to connect a hub to a server or workstation. In a straight through connection, Pin 1 at the server, Pin 2 at the hub connects to Pin 2 at the server, and so on.

  • Page 54: Connecting 100Base-Tx Fast Ethernet Network

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 5-3. Connecting 100Base-TX Fast Ethernet Network The system board provides an RJ-45 port for connection to 100Base-TX Fast Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP). The adapter automatically oper ates at 10Mbps or 100Mbps when the appropriate 10/100Base hub be connected.

  • Page 55: Remote Boot Rom Installation Guide

    User’s Manual • UTP cable should meet the following requirements: 1. Solid copper 2. Nominal capacitance: less than 16pF/ft 3. Nominal impedance: 100 ohms 4. Nominal attenuation: less than 11.5db Automatic Selection of the Media Type While the driver installs, it automatically detects the media type based on the type of cable connected.

  • Page 56: Led Indicators

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses 5-7. LED Indicators The system board comes with two LED indicators on the edge of the motherboard that indicates the network system status. If you experience any problems with the adapter, first make sure the appropriate driver is loaded, the proper cable is connected to the RJ-45 port and the hub complies with the adapter specification, such as 10Mbps 10Base-T or 100Mbps 100Bast-TX.
  • Page 57 User’s Manual Note: Before running the setup program, make sure the adapter’s driver is not loaded, otherwise unpredictable results may arise! The setup program can be set the on board configuration to provide diagnostic testing. It is for testing the basic function verification, EEPROM data Access, loopback operation, and the ability to communicate over the network with another adapter.
  • Page 58 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses • Diagnostics On Board: Performs on board basic function verification • Diagnostics On Network: To run this test on the network, you will need another computer set up as a Responder to receive packets from the adapter being tested and echo them back to the adapter.

  • Page 59: Lan Driver Installation Procedure

    User’s Manual 5-9. The Realtek 8139 LAN Driver Installation Procedure: Please note: The LAN Driver installation has to be done after completing Win 95/98/2000 installation. When completed with the WIN 95/98 installation, please click “My Computer” to start your LAN driver installation (procedure listed as below): My Computer è...

  • Page 60: Appendix A: Flash Memory Utility

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Appendix A: FLASH Memory Utility Using this utility to update the system BIOS from a disk file t o the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction.

  • Page 61: Appendix B: Connector Pin Assignment

    Appendix B: Connector Pin Assignment PS/2 Keyboard / Mouse Pin Header Connector (ENDAT-5701: CN4; ENDAT-5901: CN6) Pin No. PS/2 Keyboard Description Pin No PS/2 Mouse Description K/B_Data Mouse_Data Grounded Grounded +5V DC Mouse_VCC K/B_Clock Mouse_Clock COM1 or COM3, COM2 or COM4 for standard RS232 defined Pin No.
  • Page 62 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses VGA Connector Pin No. Description Pin No. Description GREEN BLUE DDC DAT H.Sync V.Sync DDC CLK TOUCH Panel Controller via COM1 Pin No. Description Pin No. Description -RTS1 TXD1 RXD1 TTL Output via COM2 Pin No.
  • Page 63 User’s Manual LCD Panel 18Bit / 16Bit TFT/DSTN Mapping Signal 16Bit DSTN 18Bit/18+18 TFT Pin No. N.C. FPD23 N.C. FPD22 FPD21 N.C. FPD20 N.C. FPD19 N.C. FPD18 N.C. FPD17 N.C. FPD16 FPD15 FPD14 FPD13 FPD12 FPD11 FPD10 FPD9 FPD8 FPD7 FPD6 FPD5 FPD4...
  • Page 64 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses LCD Connector1: (CON1) Pin No. Description Pin No. Description VDDLCD(+3.3v) VDDLCD(+3.3v) ENPVEE FPD23 FPD22 FPD17 FPD16 FPD11 FPD10 FPD9 FPD8 FPD21. FPD20 FPD15 FPD14 FPD7 FPD6 FPD5 FPD4 FPD19 FPD18 FPD13 FPD12 FPD3 FPD2...
  • Page 65 User’s Manual Audio Output Port Connector (5701:CN7; 5901:CN10) Pin No. Description Pin No. Description A_BIT_CLK TV_COMP A_SD_IN TV_LUMA A_SD_IN2 TV_CRMA A_SD_OUT A_RESET A_SYNC SPEAKER AUDIO ENABLE/DISABLE VCC3 +12V JBCY JAB2 JBCX JAB1 JACY JBB2 JACX JBB1 JMS0 JMSI FDD Connector Pin No.
  • Page 66 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses IDE1, IDE2 Connector Pin No. Description Pin No. Description 2,19,22 IDE data2 24.26.30 IDE data13 IDE data1 20,21,28 IDE data14 29,32,34 IDE data0 IDE reset IDE data15 IDE data7 IDE Write IDE data8 IDE Read...
  • Page 67 User’s Manual External Speaker Connector (5701:J3; 5901:J4) Pin No. Description USB PORT 1/2 : (5701:CN11; 5901: CN1) Pin No. Description USB VCC USB DATA -(0,1) USB DATA+(0,1) USB_GND USB_GND IR Connector (5701:IR1; 5901: J7) Pin 1 Pin 4 IRRX Pin 2 Pin 5 IRTX Pin 3...
  • Page 68 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses Expansion Slot to PCI/ISA Pin Assignment Description A Description B Description E Description F -IOCHK RSTDRV -PCINT2 -PCINT4 IRQ9 -PCINT3 -PCINT1 DRQ2 -12V -PCIRST PCLKF +12V -GNT3 10 IOCHRDY -REQ3 GNT1 11 AEN -SMEMW...
  • Page 69 User’s Manual Description C Description D Description G Description H -SBHE -MEMCS16 -SERR LA23 -IOSC16 AD15 LA22 IRQ10 -CBE1 AD14 LA21 IRQ11 AD12 LA20 IRQ12 LA19 IRQ13 LA18 IRQ14 LA17 -DACK0 AD13 AD10 -MEMR DRQ0 AD11 10 -MEMW -DACK5 11 SD8 DRQ5 -CBE0 12 SD9...

  • Page 70: Appendix C: Limited Warranty

    ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses LIMITED WARRANTY: Standard one year limited warranty on all our ENDAT series all-in-one motherboards and embedded board. Products that become defective during the warranty period shall be repaired, or subject to manufacturer’s option, replaced. The limited warranty...
  • Page 71 User’s Manual RMA SERVICE REQUEST FORM When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. RMA NO.: Company: Person to Contact: Phone No: Purchase Date : Fax No.
  • Page 72 ENDAT-5701 and ENDAT-5901 All-In-One motherboard uses l Issue Code of defect. Second Times R.M.A. Memory Socket Bad No Screen (No Boot) 12 Hang Up Hardware VGA (Display) Fail 13 Hang Up Software CMOS Data Lost 14 PCB Problem FDC Fail...

This manual is also suitable for:

Endat-5901

Table of Contents