Contents Important safety information Description of the appliance The control panel Before use Setting the water softener Filling with salt Rinse aid Use of detergent Using your appliance Loading your appliance Adjusting the height of the upper basket Hints and tips Washing programmes Operating sequence Maintenance and cleaning...
Important safety information It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information.
Control panel 1. On/Off push button Audible signals Audible signals have been introduced to help indicate which 2. Salt and rinse aid refilling indicator operations the dishwasher is performing. lights Short "instruction accepted" signal When any of the pushbuttons are pressed, a short audible 3.
Before use Before using your dishwasher for the first time: 1. Ensure that the electrical and water connections comply with the installation instructions 2. Remove all packaging from inside the appliance 3. Set the water softener 4. Pour 1 litre of water inside the salt container and then fill SO424 with salt 3.
Rinse aid Use of detergent Rinse aid is automatically added during the last rinse, Only use detergents specifically designed for use in ensuring thorough rinsing, and spot and streak free drying. dishwashers. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 If using powder detergents proceed as follows: dishwashing programmes, depending upon the dosage...
Using your appliance Loading your appliance Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from Before placing dishes in the machine, remove any scraps of the bottom of the basket, obstructing the lower spray arm, food, to avoid clogging the filters and consequently reducing load the cutlery with the handles facing upwards.
Hints and tips Adjusting the height of the upper To save energy basket Place dishes in the machine immediately after every meal and wait until the dishwasher is full before washing. If washing very large plates (over 27 cm and up to 32 cm in If necessary run the Rinse and Hold programme (see diameter) you can load them in the lower basket after moving "Washing Programmes"...
Washing programmes Programme Degree of soil and Recommended quantity Cycle description type of load of detergent wash prewash 1 cold rinse, Any. (to avoid food scraps from Rinse and Hold Partial load (to be completed later in the day). sticking together). Hot prewash Main wash up to 70°C Heavy soil.
Operating sequence 1. Check the filters The digital display shows the delay time (flashing dot in the display indicate that the countdown is going on), Ensure they are clean and properly positioned (see which will decrease with steps of 1 hour. "Maintenance and cleaning").
Maintenance and cleaning Internal cleaning The dishwasher must not be used without filters. Incorrect repositioning and fitting of the filters will Ensure that the seals around the door, the detergent and rinse produce poor washing results. aid dispensers are cleaned regularly with a damp cloth. Cleaning the filters is vital to ensure correct operation of We recommend every 3 months to run a 65°C wash the machine.
Something not working Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. The dishwasher is fitted with a number of alarm systems which can help you to quickly determine the cause of any problems. The dishwasher will not start or stops during operation, all push buttons are inoperative except for the On/Off push button.
If after all these checks, the problem persists, contact your local Service Force Centre, quoting the model and serial number. This information can be found on the rating plate located on the right hand side of the dishwasher door (see picture).
Hints for test centres Before starting any test it is necessary to fill completely with salt the salt container and with rinse aid the rinse aid dispenser. Test standard: EN 50242 Reference programme: Programme 6 (Bio 50°C with prewash) Load: 12 standard place settings Rinse aid selector: position 5...
Installation instructions Remove all packaging before positioning the machine. The waste connection must be at a height of between 30 cm (minimum) and 100 cm (maximum) from the bottom of the If possible, position the machine next to a water tap and a dishwasher.
Need help?
Do you have a question about the E 60 LS-E and is the answer not in the manual?
Questions and answers