1. Manuals
  2. Brands
  3. DMX Manuals
  4. Multiplexer
  5. SOUNDLIGHT 3006A Mk5
  6. Operating manual

DMX SOUNDLIGHT 3006A Mk5 Operating Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATING MANUAL
DMX Demultiplexer 3006A Mk5
(C) SOUNDLIGHT 1995-2003 * ALL RIGHTS RESERVED * NO PART OF THIS MANUAL MAY BE REPRODUCED,
DUPLICATED OR USED COMMERCIALLY WITHOUT THE PRIOR WRITTEN CONSENT OF THE OWNER * ALL
STATEMENTS WITHIN THIS MANUAL HAVE BEEN CHECKED CAREFULLY AND ARE BELIEVED TO BE
ACCURATE, HOWEVER SOUNDLIGHT DOES NOT ASSUME ANY RESPONSIBILITY FOR ERRORS OR
OMISSIONS. * THE USER HAS TO CHECK THE SUITABILITY OF THE EQUIPMENT FOR THE INTENDED USE.
SOUNDLIGHT EXPRESSLY EXCLUDES ANY RESPONSIBILITY FOR DAMAGES - DIRECT OR INDIRECT - WHICH
MAY OCCUR DUE TO MISUSE, UNPROPER INSTALLATION, WRONG OPERATING CONDITIONS AND NON-
COMPLIANCE TO THE INSTRUMENT'S INSTRUCTIONS, AS WELL AS IGNORANCE OF EXISTING SAFETY
REGULATIONS.
SOUNDLIGHT
Glashüttenstrasse 11 D-30165 Hannover Tel.: 0511-3730267
The DMX Company
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SOUNDLIGHT 3006A Mk5 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for DMX SOUNDLIGHT 3006A Mk5

  • Page 1 OPERATING MANUAL DMX Demultiplexer 3006A Mk5 (C) SOUNDLIGHT 1995-2003 * ALL RIGHTS RESERVED * NO PART OF THIS MANUAL MAY BE REPRODUCED, DUPLICATED OR USED COMMERCIALLY WITHOUT THE PRIOR WRITTEN CONSENT OF THE OWNER * ALL STATEMENTS WITHIN THIS MANUAL HAVE BEEN CHECKED CAREFULLY AND ARE BELIEVED TO BE ACCURATE, HOWEVER SOUNDLIGHT DOES NOT ASSUME ANY RESPONSIBILITY FOR ERRORS OR OMISSIONS.
  • Page 2 The SOUNDLIGHT DMX Demultiplexer 3006A is an intelligent DMX demultiplexer, able to decode digital data complying with USITT standard DMX-512, or DIN 56930-2 respectively, to analog output voltages of 0-10V DC. The board can be used with all standard light control systems. Its special...
  • Page 3 ERROR (blinking) No error indication while normal operation Error blinking at data errors or loss of communication. 1x green, 2x red: Start address setting too high, not enough DMX data available to serve all outputs. 1xgreen, 6x red: Service routines active...
  • Page 4 At signal loss all outputs are set to 0% after the minimum hold time has expired. This leads to a well defined state of the lighting system. In some cases it may be preferred to set the output to full level instead, or hold the last valid DMX setting. These options are available by setting the configuration DIP switches CONFIGURATION The demultiplexer 3006A may be configured by the four DIP-switches on the adress board.
  • Page 5 3006A-EP CE CONFORMITY This DMX demultiplexer is microprocessor controlled and uses high frequence (16 MHz quartz). The interface has been tested in our emc lab to comply with EN5022B and IEC65/144. To ensure the best performance regarding radiated and conducted emissions we suggest to install the interface card in a closed, conductive (e.g.
  • Page 6 - connection to wrong voltage or current; - misuse. SERVICE There are no parts within the DMX Demultiplexer Board 3006A which require the user's attention. Should your unit require servicing, please send it to the factory, freight paid. INTERNET-HOTLINE Please use our internet domain http://www.soundlight.de for new versions, updates etc. If you have any comments which may be worth considering, please send a message to info@soundlight.de.

Table of Contents