Table of Contents
Advertisement
Available languages
Available languages
Quick Links
INSTALLATION INSTRUCTIONS
1a. Install the Brackets — Inside Mount
Intermediate Bracket
Right Hand
Bracket
/
"
3
8
Side or Top Installation
Install each bracket with two screws, either through the side or up through
the top. Minimum 1 1/8" mounting surface height requirement.
For Intermediate Bracket (if required), space evenly between the two end
brackets. Make sure all brackets are leveled and aligned.
For Flush Mount with Valance, the minimum is 3 1/2" for 1 3/8" and 2" slat
and 3 7/8" for 2 3/8" and 2 1/2"slats.
1c. Using Extension Brackets (optional)
Position the extension brackets to the wall markings made on step 1.
The bracket tops must be aligned and level to one another.
First, mount the extension brackets with screws through diagonal holes.
Attach the installation brackets to the extension brackets. Then, mark where
the ends of the headrail will be positioned and install each bracket with two
screws either through the back.
For Intermediate Bracket (if required), space evenly between the two end
brackets. Make sure all brackets are leveled and aligned.
Left Hand
(optional)
Bracket
Right Hand
Bracket
First, mark where the ends of the headrail will be positioned. Then, install
each bracket with two screws through the back. Minimum 1 3/4" mounting
surface height requirement.
For Intermediate Bracket (if required), space evenly between the two end
brackets. Make sure all brackets are leveled and aligned.
Important: On 2-3/8" & 2-1/2" slats, spacer blocks will be attached to the
end of each bracket (if extension brackets are not used).
First, open the installation brackets door latches by pressing up on the
bracket bottoms while lifting the doors open. Then, slide the headrail into
the brackets and push it all the way back. The front lip of the headrail should
hook to the center support lips (if installed). Finally, snap the door shut over
the locking tab to secure it.
WOOD & FAUX BLINDS
Tilt Only
1b. Install the Brackets — Outside Mount
Intermediate Bracket
(optional)
Spacer Block
(if necessary)
2. Install the Blind
1
2
Left Hand
Bracket
3
Click
1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ALTA WOOD
Summary of Contents for ALTA WOOD
- Page 1 WOOD & FAUX BLINDS INSTALLATION INSTRUCTIONS Tilt Only 1a. Install the Brackets — Inside Mount 1b. Install the Brackets — Outside Mount Left Hand Left Hand Intermediate Bracket Bracket Bracket Intermediate Bracket Right Hand (optional) (optional) Bracket ” Right Hand...
- Page 2 INSTALLATION INSTRUCTIONS 3a. Install Components — Hold-Down (Optional) 3b. Install Components — Wand (Optional) First, lower the blind and connect the bottom rail pins to the hooks on both sides. Then, mark the hold-down bracket locations on the mounting surface. With the brackets level, attach the hold-downs using the provided screws.
- Page 3 STORES EN BOIS ET SIMILIBOIS INSTRUCTIONS D’INSTALLATION Inclinaison seulement 1a. Installez les supports — Montage intérieur 1b. Installez les supports — Montage extérieur Support Support Support intermédiaire gauche gauche Support intermédiaire Support (facultatif) (facultatif) droit Support 3/8 po droit Bloc d’espacement (si nécessaire) Montage de côté...
- Page 4 INSTRUCTIONS D’INSTALLATION 3a. Installez les composants – Taquets de retenue (facultatif) 3b. Installez les composants — Baguette (facultatif) Tout d’abord, abaissez le store et connectez les épingles de la traverse in- férieure aux crochets des deux côtés. Ensuite, marquez les emplacements des taquets de retenue sur la surface de montage.
Need help?
Do you have a question about the WOOD and is the answer not in the manual?
Questions and answers