Summary of Contents for Hercules LT0892
- Page 1 Instruction Manual Lateral Pallet Tilter (LT0892) Note: Owner/Operator must read and understand this instruction manual before using the lateral pallet tilter.
- Page 2 · The safety rules, maintenance, operating instructions. · Proper application. · Risks with improper use. · Please replace the bolt with hole of Part No.138 before use. 2. General specifications Model LT0892 Capacity (kg) ≤25 Pressure (MPa) Max. Fork Height (mm) Min.
- Page 3 nearer to the stacking area, then turn the winch to tilt the fork, overturn the material to the stacking area or on the stacking goods, without unloading by man, which is safe and free of labor. 3.3 Because the capacity of load is not big, the height of stacking is not high, the operating force of winch is not big when tilting.
- Page 4 4.1.4 Avoid offset loads Except obeying the regulation of diagram, the load must be distributed evenly on forks or pallets, avoid of left or right offset, then the load will not overturn when lifting or transporting. 4.1.5 Driving loaded The machine is designed for use on even and level floor. During transport the forks shall be raised as little as possible.
- Page 5 5.1 Lifetime of the machine Regular inspection, repair and the replacement of worn or defective parts in good time will prolong the life of the machine. “Prevention is better than repair”, therefore ensure: 5.1.1 Correct usage. 5.1.2 Regular cleaning. 5.1.3 Oil changes at the correct intervals. 5.1.4 Periodic safety inspection.
- Page 6 5.5 The safety valve does not seal completely The safety valve (W) will open when the load reaches the 20% of the capacity, the safety valve must seal completely in capacity, no leakage. (This has been set in factory, do not regulate it under general conditions.) With a certain load on the forks, press the pump rod by the control lever quickly so that oil quickly flows over the hydraulic valve.
- Page 7 lever and the regulating screw (140M) on the crank link (139M) to make the crank link be dragged (now the lowering valve is open, but hydraulic valve is close), while the forks in the state of neither lower nor lift position. 5.7.3 Adjustment of lifting position Place the handle bar in lifting position.
- Page 8 back is low). To ensure the same load on all rollers, the eccentric axle (F5922) must be adjusted on both sides and to the same position. Tighten setting screw M8 of each side after adjustment. Note: The eccentric axle can only adjust the front or back of fork, can’t adjust the tilting clearance of left or right of fork.
- Page 9 - Pressure valve does not -Adjust pressure The forks sink seal completely. valve. after they have -Seals leakage. -Replace seals with new been raised. ones. - Air in the hydraulic oil. -Expel the air. The forks lifting -Discharge valve is not -Adjust discharge speed...
- Page 10 Hydraulic Assembly...
- Page 11 Parts List of Hydraulic Assembly Q’ty Q’ty Parts No. Description Parts No. Description 5900 Hydraulic assembly 1154A Pump cylinder 5901 1155A Seal ring 5902 Welded frame Screw 1101 Dust proof ring Red copper washer 1102 Cylinder Spring 1103 O-ring Pressure rod 1104 O-ring Steel ball...
- Page 12 Frame Assembly...
- Page 13 Parts List of Frame Assembly Q’ty Q’ty Parts No. Description Parts No. Description F5901 Spring pin F1114 Dividing bush F5902 Load roller axle F1115 Steering wheel bracket F5903 Bearing F1116 Locking nut F5904 Dividing bush F1117 Hexagon nut F5905 Frame assembly F1118 Control level of brake F5906...
- Page 14 Carriage Assembly...
- Page 15 Parts List of Carriage Assembly Parts Parts Q’ty Q’ty Description Description F5919 Setting screw F5932 Bearing F5920 Welded carriage F5933 Pin F5921 Sliding pad F5934 Plain washer F5922 Eccentric axle F5935 Bolt F5923 Plastic plate F5936 Fixing block F5924 Screw F5937 Fork assembly F5925 Runner bracket...
- Page 16 Parts List of Handle Q’ty Q’ty Parts No. Description Parts No. Description H5901 Control level H1109 Retaining ring H5902 Steel wire rod H1110 Bushing H5903 Axle H102 Spring pin H5904 Spring pin H103 Spading plate H5905 Chain H104 Spring pin H5906 Guiding rod H105 Spring pin...
-
Page 17: Assembly List
Assembly list Assembly Description 5900 Hydraulic ass’y Lowering valve ass’y Hydraulic valve ass’y Safety valve ass’y...
Need help?
Do you have a question about the LT0892 and is the answer not in the manual?
Questions and answers