Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Charge Amps Aura Dual Pole Mount
Summary of Contents for Charge Amps Aura Dual Pole Mount
- Page 1 Charge Amps Aura Dual Pole Mount Installation manual...
-
Page 2: Table Of Contents
Contents of the package ................. 5 Provided by the installer .................. 5 Before installation ..................5 Model view Aura Dual Pole Mount ..............6 Mounting Aura on the pole mount ..............7 Warranty conditions ..................19 Safety precaution .................... 19 Mechanical information................... -
Page 3: User Agreement
User Agreement The user agrees to the following: Aura Dual Pole Mount is an accessory for the Charge Amps Aura charging station. It cannot be used without two Charge Amps Auras installed properly. The Aura Dual Pole Mount and the two Charge Amps Auras should be regarded as one assembly. The power should be switched off during the complete installation. -
Page 4: Greetings Installer
Installation may only be carried out by a qualified installer who follows: Basic safety precautions for safe and correct installation. • Local, regional, and national installation regulations. • The instructions in this Aura Dual Pole Mount installation manual. • © 2021 Charge Amps AB Address: Contact: Org. -
Page 5: About Aura Dual Pole Mount
By adding the Pole Mount, specifically designed for Aura, you open up the possibilities for installing two chargers on a 60 mm outer diameter pole e.g. an existing motor heater pole. Contact your supplier for more information about your specific Aura Dual Pole Mount. Contents of the package... -
Page 6: Model View Aura Dual Pole Mount
Model view Aura Dual Pole Mount Aura Dual Pole Mount 2. Din Rail 3. Lid 4. 1 pcs. EPDM Gasket 5. 4 pcs. M6 x 30 screws (Note: Included in the Aura installation kit) 6. 4 pcs. of each M6 screws, washers and nuts 7. -
Page 7: Mounting Aura On The Pole Mount
Step 2 The Aura Dual Pole Mount is 380 mm in height. It adds 280 mm height to the pole. If the pole needs to be cut, then make sure to do it at this step and make sure that there are no installation cables that can be damaged or in contact to the cutter. - Page 8 Slide the O-ring onto the pole. Then slide the pole mount onto the pole. Make sure that the O-ring is between the pole mount and the pole and not at the same level as the pin stop screws. © 2021 Charge Amps AB Address: Contact: Org.
- Page 9 M6. Make sure that the pole mount is fixated and in an upright position. If the pole has a slight angle, the pole mount can be straightened by tightening the pin stops screws differently. © 2021 Charge Amps AB Address: Contact: Org.
- Page 10 The bracket will not be used when having the Aura on the pole mount. The screws will be reused. 2. Slide the first Aura onto the pole mount according to the picture below. © 2021 Charge Amps AB Address: Contact: Org.
- Page 11 Step 6 Tape the EPDM Gasket, highlighted in blue, to the bottom of the Aura according to the picture below to prevent water and moist to drip down in the pole mount. © 2021 Charge Amps AB Address: Contact: Org. No. 556897-7192...
- Page 12 Slide the next Aura unit to the pole mount as described in Step 5. 2. Fixate both Auras by tightening the four horizontal M6 x 30 screws, washers and nuts. © 2021 Charge Amps AB Address: Contact: Org. No. 556897-7192...
- Page 13 Side/Front view 3. Tighten the four vertical M6 screws connecting the Aura Dual Pole Mount to the Aura:s. View from below © 2021 Charge Amps AB Address: Contact: Org. No. 556897-7192 Installation manual for Charge Amps AB +46 (0)8 55 11 2000...
- Page 14 WPD 501 2X25/2X16 1XGN/3XGY/1XBL, order nr 1562140000, at Weidmuller.com. Adjust the height of the terminal block by sliding it on the Din Rail and connect it. © 2021 Charge Amps AB Address: Contact: Org. No. 556897-7192...
- Page 15 3. Cut new appropriate cables, connect them to upper side of the terminal block and pull them through the bottom of the Aura. Connect the first set of cables to the poles closest to the back. © 2021 Charge Amps AB Address: Contact: Org.
- Page 16 1XGN/3XGY/1XBL, order nr 1562140000, at Weidmuller.com. Adjust the height of the terminal block by sliding it on the Din Rail and connect it. Connect the first set of cables to the poles closest to the back. © 2021 Charge Amps AB Address: Contact: Org.
- Page 17 3. Remove the lid from one of the Auras. Use one of the PE poles from one of the Auras and connect it to the earthing screw of the Aura Dual Pole Mount. © 2021 Charge Amps AB...
- Page 18 IP 44 protection will fail. Step 9 Unlock and remove the lid from the Auras. Read the Aura installation manual and install them accordingly, then close and lock the front. © 2021 Charge Amps AB Address: Contact: Org. No. 556897-7192...
-
Page 19: Rights
IP 44 when installed properly • Product recycling Recycling is part of any products lifecycle. Aura Dual Pole Mount contains stainless steel and should be recycled accordingly. Rights The information in this document has been checked for accuracy. Charge Amps AB reserves the right to make technical changes and changes to the contents of the document without prior notice.