Advertisement
Quick Links
FLAT MATE DISPLAY
PX7025
Assembly Instructions
Important!
Please read these instructions carefully before beginning to assemble
Revision: AB-220309
this display. Save these instructions for future reference.
Poly-Tex, Inc.
• PO Box 458, 27725 Danville Ave, Castle Rock, MN 55010 • (800) 852-3443 • (651)463-7009 • Fax (651) 463-7279 •
www.poly-tex.com
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Poly-Tex PX7025
- Page 1 FLAT MATE DISPLAY PX7025 Assembly Instructions Important! Please read these instructions carefully before beginning to assemble Revision: AB-220309 this display. Save these instructions for future reference. Poly-Tex, Inc. • PO Box 458, 27725 Danville Ave, Castle Rock, MN 55010 • (800) 852-3443 • (651)463-7009 • Fax (651) 463-7279 •...
-
Page 2: Optional Parts
PR1146 PK1146 PG1146 Part number references are included in the instructions for the galvanized components. Refer to the second letter change in the part number for cross reference to the appropriate powder-coated color. PX7025 Flat Mate Display-Single Revision AB-220309... - Page 3 CARRIAGE BOLT 1/4”x 1-3/4” G5 NB1860 LOCK WASHER 1/4 ZP NB1902 WING NUT 1/4" ZP Questions? Please call Poly-Tex, Inc • PO Box 458, 27725 Danville Ave, Castle Rock, MN 55010 • (800) 852-3443 • (651)463-7009 • Fax (651) 463-7279 • www.poly-tex.com...
- Page 4 Position the other End Frame at approximately the proper spacing and hold one Stabilizer above the two frame pins with the bend hanging down, as shown. Engage the Stabilizer on the lower pin first, then position the other, and rotate 90° until the Stabilizer is tight against the frame post. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 5 Stabilizers are nearly in the same plane. Install the Snapper Pin NB1996 through the holes in the center of the Stabilizers and snap closed. Align the Bench Frames parallel with each other and square with the Stabilizer group. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 6 Engage the front of the Bench Top under the front tabs and lower the bench in place. Repeat the above instructions for each of the other Bench Tops. Frames will not have the tabs at every level. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 7 Prior to assembly of Display, turn each Base Frame on the back and remove the two Square Plugs, RS5001 from bottoms of the posts. Insert a Caster stem fully into each post and rotate the collar of each caster until it fits firmly in place. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 8 Insert a Purlin Extension PX1106 in each back post with the projection facing forward. Position a Basket Purlin GM4000 under the lower clips of each Purlin Extension and rotate 180° until the purlin is secure. Repeat the action for the upper Basket Purlin. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 9 Attach Sign Holder with two bolts, washers, and nuts. Continuous runs of benches use a common Sign Post between Sign Holders. Signs may be installed back-to-back using the same set of hardware. PX7025 Flat Mate Display-Single Revision AB-220309...
- Page 10 FLAT MATE DISPLAY-SGL EXT Assemble the Extension in the same manner and sequence as the original base and accessories. NOTE: Extended runs of this product are not intended to be used on Casters. PX7025 Flat Mate Display-Single Revision AB-220309...
-
Page 11: Safety Guidelines
Limited Warranty Poly-Tex Inc. warrants its products to be free from defects in material and workmanship for a period of (1) year from date of invoice. This warranty is provided to the original purchaser of the product and is not transferable. Poly-Tex does not warrant parts not manufactured by Poly-Tex, but does assign any transferable manufacturer or supplier warranties.
Need help?
Do you have a question about the PX7025 and is the answer not in the manual?
Questions and answers