Summary of Contents for Pepwave Peplink BLE
- Page 1 Peplink BLE Module User Manual Peplink Products: BLE module 2 - pcb antenna June 2020 https://www.peplink.com Copyright @ 2020 Peplink...
-
Page 2: Table Of Contents
Table of Contents 1. Introduction ..................3 2. Product Features .................. 3 3. Power Specitifications ................. 5 4. RF Specifications ................. 7 5. Appendix ....................8 https://www.peplink.com Copyright @ 2020 Peplink... -
Page 3: Introduction
1. Introduction BLE module 2 - pcb antenna ) The BLE module is used nRF51822 ultra-low power 2.4 GHz wireless System on Chip (SoC) integrating the nRF51 series 2.4GHz transceiver, a 32 bit ARMR Cortex™-M0 CPU, flash memory, and analog and digital peripherals.nRF51822 can support BluetoothR low energy and a range of proprietary 2.4 GHz protocols, such as Gazell from Nordic Semiconductor. - Page 4 • 8/9/10 bit ADC - 8 configurable channels • 31 General Purpose I/O Pins • One 32 bit and two 16 bit timers with counter mode • SPI Master/Slave • Low power comparator • Temperature sensor • Two-wire Master (I2C compatible) •...
-
Page 5: Power Specitifications
3. Power Specifications. Power supply The nRF51 supports three different power supply alternatives: • Internal LDO setup • DC/DC converter setup • Low voltage mode setup See Table for the voltage range on the different alternatives. circuitry” for details on the schematic used for the different power supply alternatives. Internal LDO setup In internal LDO mode the DC/DC converter is bypassed (disabled) and the system power is generated directly from the supply voltage VDD. - Page 6 Power management The power management system is highly flexible with functional blocks such as the CPU, Radio Transceiver, and peripherals having separate power state control in addition to the global System ON and OFF modes. In System OFF mode, RAM can be retained and the device state can be changed to System ON through Reset,GPIO DETECT signal, or LPCOMP ANADETECT signal.
-
Page 7: Rf Specifications
• 1V2 with the startup time t • One of the following clock sources • RC16 with the startup time t START,RC16 • XO16M/XO32M with the startup time the clock management system t Constant Latency In Constant Latency mode the system is optimized towards keeping the CPU latency and the PPI task response constant and at a minimum. -
Page 8: Appendix
• 1 MHz non-overlapping channel spacing at 1 Mbps and 250 kbps • 2 MHz non-overlapping channel spacing at 2 Mbps • Works with low-cost 60 ppm 16 MHz crystal oscillators ± • Baseband controller • EasyDMA RX and TX packet transfer directly to and from RAM •... - Page 9 FCC other Parts, Part 15B Compliance Requirements for Host product manufacturer This modular transmitter is only FCC authorized for the specific rule parts listed on our grant, host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
- Page 10 Antenna Type Brand/ manufacturer Model No. Max. Antenna Gain Brand: PEPXIM; PEPWAVE; peplink P013 antenna 5dBi PCB antenna Manufacturer: PISMO LABS TECHNOLOGY LIMITED Antenna Change Notice to Host manufacturer...
- Page 11 OEM Integration Instructions： This device is intended only for OEM integrators under the following conditions： The module can be used to installation in other host. the transmitter module may not be collocated with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module.
Need help?
Do you have a question about the Peplink BLE and is the answer not in the manual?
Questions and answers