Contents 1. Introduction...............2 2. Product information and operation......3 2.1. Control panel.............3 2.2. Switching on and off (stand-by)......4 2.3. Select product to program......5 2.4. Adjust the Day/Time.........5 2.5. Set the temperature..........5 2.6. Lock the keypad..........5 2.7. MANUAL/AUTOMATIC function......6 2.7.1 MANUAL function........6 2.7.2 AUTOMATIC function......7 2.7.3 Pre-installed programmes.....9 2.8.
2. Product information and operation 2.1. Control panel 2.1.1. Keypad DESCRIPTION TFT display Send information button Adjust day and time button Decrease temperature button MANUAL / AUTOMATIC function Pre-installed programme 1 button Pre-installed programme 2 button Pre-installed programme 3 button Pre-installed programme 4 button On / Off button Accept / Confirm button...
2.1.2. TFT display panel DESCRIPTION Programming Days of the week Time of day Temperature selected Control panel locked / unlocked MANUAL / AUTOMATIC function indicator COMFORT / ECO / ANTI-FROST mode indicator 2.2. Switching on and off (stand-by) To switch the product ON, please press the button once.
2.3. Select product to program After the remote has been switched on, the TFT screen will display 2 options for you to choose between: radiator, towel rail or water heater. Press to select the radiator or towel rail to program. Press to select the water heater to program.
and the keypad lock will be activated. The symbol will appear on the display panel of your product and the keys will not respond. To unlock the keypad on your product using your remote control, please hold and press the button AND the button TOGETHER for 3 seconds.
increase the temperature. Press the button to decrease the temperature. Depending on the temperature selected you will see one of the following icons: Radiator and Towel Rail Temperature Range Symbol Mode Min. Max. COMFORT 19ºC 30ºC 15ºC 18.5ºC ANTI-FROST 7ºC Water Heater Temperature range Symbol...
Page 8
and the temperature will flash. Press the button c onf ir m a nd move E C O temperature. STEP 2 - Select ECO mode temperature Select the ECO mode temperature between 15ºC and 19.5ºC. The icon and the temperature will flash. Press the button to confirm and move to the ANTI- FROST mode.
corresponding icon for that mode will appear at the top of the screen. To finish the programming press the button leave for 30 seconds without pressing any buttons. To change the programming go back to step 1 and proceed as described before. Send the adjustment to the radiator, water heater or towel rail by pressing button (see section 2.8.).
• edit pre-installed programmes activated: To modify a day of the activated pre-installed programme please press and hold either the button. This will edit the day displayed. • To edit a full pre-installed programme: When on the main screen press the pre-installed programme button you wish to edit for for 3 seconds.
3.2. Batteries The BASIC Control remote control uses two 1.5V AAA batteries. You are advised to remove the batteries from the remote control when it is not going to be used for a long period of time (e.g. a vacation/ holiday, the summer months etc.).
Page 12
ROINTE as well as incorrect installation or use of the product that may not comply with the current technical standards of safety.
Page 13
4.5. This guarantee is not transferable. 4.6. Proof of purchase will be required to ROINTE for any claim. 4.7. This guarantee does not affect your statutory rights.
Page 19
Thank you for choosing Rointe. We hope you enjoy your product. If you require further assistance or information, please contact our Technical Service Department by telephoning 0203 321 5929 or email support@rointe.co.uk.
Page 20
ROINTE UK Catalyst House, 720 Centennial Court, Centennial Park Elstree, Herts, WD6 3SY 0203 321 5928 0208 953 5861 Technical Support 0203 321 5929 E: support@rointe.co.uk www.rointe.co.uk MBCUK17V2...
Need help?
Do you have a question about the BASIC control and is the answer not in the manual?
Questions and answers