Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Norton MTA 36
Summary of Contents for Norton MTA 36
- Page 1 MTA 36 OPERATING INSTRUCTIONS AND SPARE PARTS LIST...
- Page 3 Declaration of conformity The undersigned manufacturer: SAINT - GOBAIN ABRASIVES S.A. 190, BD J.F. KENNEDY L- 4930 BASCHARAGE Declares that this product: MTA 36 P5.5 HONDA 70184614008 Power Float: Code: MTA 36.303 70184613921 is in conformity with the following Directives: ...
-
Page 5: Table Of Contents
MTA36 OPERATING INSTRUCTIONS AND SPARE PARTS LIST Basic Safety Instructions Symbols Machine plate Safety instructions for particular operating phases Machine description Short description Purpose of use Layout Technical Data Assembly and commissioning Safety guard ring and handle Tool assembly Starting the machine Transport and storing Securing for transport Transport procedure... -
Page 6: Basic Safety Instructions
1 Basic Safety Instructions The MTA36 is exclusively designed for the finishing of wet concrete floors mainly on construction sites. Uses other than the manufacturer's instructions shall be considered as contravening the regulations. The manufacturer shall not be held responsible for any resulting damage. Any risk shall be borne entirely by the user. -
Page 7: Machine Plate
Always cut with the safety guard ring in position. Only fit NORTON blades or plates to the machine! The use of other tools can damage the machine! Attention is drawn to the use of BS2092 safety goggles in conformity with specified Processes No.8 of the Protection of Eyes Regulation 1974, Regulation 2(2) Part 1. -
Page 8: Purpose Of Use
The machine and its component parts are assembled to high standards assuring long life and minimum maintenance. 2.2 Purpose of use The Clipper Mechanical Trowel MTA36 is designed for onsite finishing operations on wet concrete floors. It is not designed for any other purpose. 2.3 Layout Handle (1) Jig welded steel construction including 2 rubber grips. -
Page 9: Technical Data
3.2 Tool assembly Only NORTON blades or plate with a maximum diameter of 865 mm can be used with the MTA36. Before mounting a new tool into the machine, switch off the machine. Screw the 2 M8-screws per blade using a 13mm wrench to assemble the blade on the arm. To... -
Page 10: Starting The Machine
assemble a plate, place the machine with the blades assembled on the plate, and turn it until the blades are located in the hooks on the plate. 3.3 Starting the machine Turn the fuel valve to the ON position. Make Move the choke lever to the CLOSED position. -
Page 11: Transport And Storing
4 Transport and storing 4.1 Securing for transport Before transporting the machine, always remove the tool. 4.2 Transport procedure Two people are necessary to move the machine. The machine does not have lifting hooks. 4.3 Long period of inactivity If the machine is not going to be used for a long period, completely clean the machine and disassemble the tool. -
Page 12: Maintenance And Servicing
operation of float blades on wet concrete. For the finishing operation, tilt the blades. Start with a small pitch of 4 to 6 mm. After each finishing pass, continue to tilt blades. Depression or high spot To fill a depression or cut down a high spot, simply move the machine back and forward over the area until the desired surface is obtained. -
Page 13: Maintenance Of The Engine
6.2 Maintenance of the engine Regular service period Perform at every indicated month or operating hour interval, whichever comes first Check level Engine oil Change Check Air cleaner filter Clean Fuel strainer cup Clean Spark plug Check-Clean Fuel line Check (Replace if necessary) Every 2 years Engine oil... - Page 14 Air cleaner To service the air cleaner filter, follow these instructions: Remove the nut, air cleaner cover and wing nut. Remove the pre air cleaner elements and separate them. Carefully check both elements for holes or tears and replace if damaged. ...
- Page 15 Spark plug To service the spark plug, follow these instructions: Visually inspect spark plug. Discard the plug if the insulator is cracked or chipped. Remove carbon or other deposits with a stiff wire brush. Measure the plug gap with a wire-type feeler gauge.
-
Page 16: Faults: Causes And Cures
Spare parts for the motor can be ordered with the manufacturer of the motor or with their dealer, which is often quicker and cheaper. This machine has been manufactured by Saint-Gobain Abrasives S.A. 190, Bd. J.F. Kennedy L- 4930 BASCHARAGE Grand-Duché de Luxembourg. Tel.: 00352-50401-1 Fax: 00352- 50 16 33 http://www.construction.norton.eu e-mail: sales.nlx@saint-gobain.com... - Page 17 Norton.edilizia@saint-gobain.com e-mail: nortonbp@axelero.hu Austria Czech Republic Saint-Gobain Abrasives GmbH Norton Diamantove Nastroje Sro Telsenberggasse 37, Vinohrdadska 184 A-5020 SALZBURG CS-13000 PRAHA 3 Tel: 0043 662 43 00 76 77 Tel: 0042 0267 13 20 21 Fax: 0043 662 43 01 75...
-
Page 18: Appendix
8 Appendix 8.1 Spare parts list POS. ART.NUMB. DENOMINATION TYPE (*) REMARKS 00310004667 Handle compl. 00310004985 Top handle 00310004984 Bellow handle 00310003986 Handle joint 00310004733 Handle blocking bolt assy 00310002089 Dead man handle 00310004748 Throttle cable 00310004029 Dead man handle switch 00310004635 Hydraulic pump 00310004698... -
Page 19: Exploded Parts Drawing
8.2 Exploded parts drawing... - Page 22 SAINT-GOBAIN ABRASIVES 190, Bd. J. F. Kennedy L-4930 BASCHARAGE LUXEMBOURG Tel.: ++352 50401-1 Fax: ++352 501633 e-mail: sales.nlx@saint-gobain.com www.construction.norton.eu 24.09.2008...
Need help?
Do you have a question about the MTA 36 and is the answer not in the manual?
Questions and answers