Fritsch pulverisette 16 Operating Instructions Manual
Cross beater mill
Hide thumbs
Also See for pulverisette 16:
- Operating instructions manual (42 pages) ,
- Assembly instructions manual (24 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fritsch pulverisette 16
Summary of Contents for Fritsch pulverisette 16
- Page 1 Operating Instructions Cross Beater Mill “pulverisette 16”...
- Page 2 It was verified through an audit that Fritsch GmbH satisfies the require- ments of DIN EN ISO 9001:2000. The enclosed conformity declaration specifies the directives satisfied by the Cross Beater Mill “pulverisette 16” in order to qualify for the CE mark. Device number 16.300x.00 Applies as of serial number 101...
-
Page 3: Table Of Contents
Unpacking..................... 8 Transport ....................8 Setup ....................8 Setup on a laboratory table ..............8 Fastening of the “pulverisette 16” to the universal support ....9 Electrical connection................10 Working with the “pulverisette 16” ........11 Operating elements and operation ............. 11 Operating elements and their function .......... -
Page 4: General/Introduction
General/Introduction Notes about the operating instructions • Study the operating instructions carefully. • The cross beater mill “pulverisette 16” is referred to below as the cross beater mill. • All operators must be familiar with the contents of the operat- ing instructions. -
Page 5: Explanation Of The Symbols Used On The Device And In The Operating Instructions
Attention! Warning against danger spot Observe operating instructions Attention! Mains voltage Attention! Hazard of explosion Wear ear protection! Wear protective gloves! Spraying with water forbidden! Do not step below lifted load! pulverisette 16 Page 2... -
Page 6: Brief Description Of The Device
This ensures a gentle grinding process. pulverisette 16 Page 3... -
Page 7: Technical Data
Technical data Dimensions: “pulverisette 16” approx. 560x420x445mm (height x width x depth) “pulverisette 16” with base frame approx. 1183x560x700mm (height x width x depth) Weight: “pulverisette 16” net approx. 36 kg with base frame net approx. 58 kg Operating noise... -
Page 8: Materials And Composition
00.180 % Impact plates of special steel Material no. 1.2080 Short name X 210 Cr 12 Composition 84.890 % 12.000 % 02.200 % 00.450 % 00.400 % 00.030 00.030 The composition percentages listed above represent average values. pulverisette 16 Page 5... -
Page 9: Operating Safety
• Do not remove the instruction labels. • Do not disable safety devices. • Independent conversions of the device negate the conformity with European directives declared by Fritsch and void the war- ranty. • The cross beater mill is intended exclusively for use as speci- fied in the section 1.3.1... -
Page 10: Protective Devices
A complaint and return in insufficient packag- the warranty period ing can put your warranty claims at risk Transport Do not jolt, shake or throw the “pulverisette 16” Electronic and mechanical components can during transport be damaged In event of temperature fluctuations, protect... -
Page 11: Installation
- Mark the hole locations onto the table using the existing holes on the motor of the cross beater mill. The spacing from the holes to the front edge of the table must allow sufficient space for installation and removal of the collecting vessel and the filter hose. pulverisette 16 Page 8... -
Page 12: Fastening Of The "Pulverisette 16" To The Universal Support
Fastening of the “pulverisette 16” to the uni- versal support Lift the mill onto the support with 2 people. Important!!! Secure the device Attention! against tipping until it is com- Warning against danger spot pletely screwed in place, since the mill’s centre of gravity al- lows it to tip forward. -
Page 13: Electrical Connection
The supplied power cable does not have a plug, since the type of plug depends on the setup location and the respective national regulations. External fuse protection must be provided during connection of the po- wer cable to the mains in accordance with the regulations of the setup location. pulverisette 16 Page 10... -
Page 14: Working With The "Pulverisette 16
Working with the “pulverisette 16” Operating elements and operation Graphical view of the operating elements: pulverisette 16 Page 11... -
Page 15: Operating Elements And Their Function
ON = “pulverisette 16” is switched on OFF = “pulverisette 16” is switched off Door seal hand Opens and closes the door of the “pulverisette 16” comfort, wheel only with places tension on the door seal Pressed and rotated right = closes the door... -
Page 16: Opening And Closing The Mill Housing
In the grinding of toxic or otherwise harmful substances, there is a risk of inhalation of dusts that are harmful to health. Do not open the “pulverisette 16” and release the motor brake at the same time. Risk of injury from the unbraked cross beater. -
Page 17: Inserting The Bottom Sieve
Filter hose and collecting vessel Through the use of a textile filter hose between the “pulverisette 16” and the collecting vessel, the airflow generated by the rotating cross beater is guided away and a back draft is prevented. In addition, it ac- celerates the material throughput and ensures a gentle grinding proc- ess. -
Page 18: Readjusting The Impact Gap
PP with a feeler gauge = desired value ~ 1 mm, whereby the gap to the bottom sieve may not be < 1 mm Adjust the gap between the grinding insert and impact plate, if neces- sary. Screw the impact plates tight with a hex key M5 pulverisette 16 Page 15... -
Page 19: Cleaning
To clean the grinding chamber in the , the motor brake cross beater mill can be released with lever G. The cross beater is easy to turn, making cleaning simpler. The protection class of the is IP54 cross beater mill pulverisette 16 Page 16... -
Page 20: Maintenance
Upon a rotation of the hand wheel of max. 45°, the motor brake must be activated Motor brake o Start device o Stop device o If the braking time exceeds 0.5 seconds, contact a ser- vice technician pulverisette 16 Page 17... -
Page 21: Warranty
Online registration is also possible. More information can be found on your warranty card or on our homepage http://www.fritsch.de The company Fritsch GmbH in Idar-Oberstein and its “Technical Applica- tion Laboratory” or the corresponding national representatives would be happy to provide you with advice and assistance.
Need help?
Do you have a question about the pulverisette 16 and is the answer not in the manual?
Questions and answers