Editing.the.tone.settings; Editing The Tone Parameters - Roland Lucina AX-09 Owner's Manual

Editing the Tone Settings

Editing the Tone Parameters

You can edit tone parameters such as the volume and
reverb for a regular tone, and save your settings in a
FAVORITE memory location (p . 10) .
* You.can't.edit.the.tone.parameters.of.a.special.tone .
1. Select.the.regular.tone.whose.tone.parameters.
you.want.to.edit.(p ..9) .
2. Hold.down.the.[SHIFT].button.and.press.the.TONE.
button.of.the.tone.you.selected.in.step.1.(i .e .,.the.
TONE.button.that's.lit) .
The parameter name (
o F F
then its value ( or
3. Continue.holding.down.the.[SHIFT].button,.and.
press.the.same.TONE.button.to.switch.parameters .
The parameters will switch from top to bottom of the
"Parameter" column in the following table .
* Don't.release.your.finger.from.the.[SHIFT].button.while.
making.this.setting .
Parameter Value
OFF, ON
PS
PtN
0–127
uoL
0–127
rEu
0–127
rEL
-64–63
-64–63
At
CUt
-64–63
rES
-64–63
16
P S
) will blink in the display, and
o N
) will appear .
Explanation
Portamento.Switch
Portamento is an effect that creates a
smooth change in pitch from one note
to the next .
Portamento.Time
This specifies the time over which
the pitch will change when using
portamento . Higher values will lengthen
the time over which the pitch will reach
the next note .
Volume
This specifies the volume of the tone .
Reverb
This effect adds the reverberation that
is characteristic of a performance in a
large hall . Higher values produce deeper
reverberation .
Release.Time.(*1)
This adjusts the time from note-off
(i .e ., when you release the key) until
the sound disappears . Higher values
produce a longer release time .
Attack.Time.(*1)
This adjusts the sharpness (speed) at
which the sound begins . Higher values
produce a more gentle attack .
Cutoff.(*1)
Increasing the cutoff value will make
the sound harder (brighter); decreasing
it will make the sound more mellow
(darker) . Use this parameter to make
adjustments if the sound is too muffled
or too bright .
Resonance.(*1)
Increasing the resonance value will
produce a distinctive tonal character
that is typical of a synthesizer . If you
want to emphasize the effect of
resonance, it's a good idea to slightly
lower the cutoff .
*1 The values you specify here are an adjustment relative to the value
assigned by each tone . If this value is set to 0, the parameter will be as
specified by the tone's own settings .
4. When.the.parameter.value.appears,.continue.
holding.down.the.[SHIFT].button.and.use.the.
[INC/+]./.[DEC/–].buttons.to.edit.the.value .
MEMO
• You can make the value change more quickly by
holding down the [INC/+] / [DEC/–] button . If you want
the value to change even faster, hold down the button
and press the other button as well .
• Even while editing the value, you can play the keyboard
to hear the result .
5. Release.the.[SHIFT].button .
* If.you.select.a.different.sound.or.turn.off.the.Lucina.
AX-09's.power.in.this.state,.the.changes.you.made.will.
be.lost ..If.you.want.to.keep.your.changes,.you.must.store.
them.in.a.FAVORITE.memory.location.as.follows .
6. Press.the.[WRITE].button .
The [WRITE] button will blink .
7. Press.the.FAVORITE.[A].button.or.[B].button.to.
select.a.bank .
8. Press.one.of.the.TONE.[1]–[6].buttons.to.select.the.
memory.location.in.which.you'll.store.the.settings .
When the [WRITE] button goes out, the settings have been
stored .