Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for ELEKTROMET EJK mini
Summary of Contents for ELEKTROMET EJK mini
- Page 1 OPERATION AND MAINTENANCE MANUAL WARRANTY CARD HEATER type EJK mini for storage tanks covered inside with ceramic enamell with insulated heating element with metal head for water heaters ~ 230 V EJK mini - 1500 □ EJK mini - 2000 □...
-
Page 2: Table Of Contents
2. The plug must be accessible after the heater is installed. 3. If the power cord is damaged, it should be replaced by the manufacturer or by a specialized repair shop, or by a qualified person in order to avoid risks. 25.07.2014 ZUG ELEKTROMET... -
Page 3: General Information
The insulation of heating elements in EJK mini heaters is done by fixing them in a casing wholly made of plastic. Heating in a casing is placed in the metal head. Between the heating element and the tank there is no electrical connection so that the metal of the sacrificial anode is not deposited on the heater. - Page 4 6 - power cord (1,5 m) for 1500W – 3x1.0mm² cord for 2000W and 3000W – 3x1.5mm² cord 7 - signal lamp 8 - plug for STB connection 9 - gasket Fig. 1. Heater structure 25.07.2014 ZUG ELEKTROMET...
-
Page 5: Heater Installation
Office of Technical Inspection, using the technical data published by particular safety valves manufacturers. Safety valve opening pressure when heater type EJK mini is used must not exceed 10 bar. When installing an electric heater in a pressure tank it must be also remembered that the... -
Page 6: Electrical Connections
Electrical installation diagram is presented in the fig. 2. 1 - heating element 2 - temperature controller + 3 - resistor 4 – rectifying diode 5 - red signal diode 6 – metal head Fig. 2. Electrical installation diagram 25.07.2014 ZUG ELEKTROMET... -
Page 7: Turning On And Water Temperature Setting
(fig. 4). The switching of protection is signalized by the click sound. This operation shall be carried out only by a properly qualified person, who will define the cause of the failure and remove it. 25.07.2014 ZUG ELEKTROMET... - Page 8 2 - temperature controller knob Fig. 3 Removal of heater knob – placing of a screwdriver in a gap. 1 - cover 3 - gasket 4 - thermal protection STB Fig. 4 Pressing the thermal protection on the temperature limiter body. 25.07.2014 ZUG ELEKTROMET...
-
Page 9: Anti-Freeze Protection
7. Operating instructions A. Heaters type EJK mini do not need to be supervised during operation. However, if the water is hard, heating elements should be periodically cleaned of boiler scale as it blocks the heat flow and therefore increases the current consumption and may cause damages of heating elements. - Page 10 C, lukewarm water, directly suitable for washing in a washbasin, no accumulation of boiler scale. Ca.+45 C, moderately hot water, slight accumulation of boiler scale. Ca.+65 C, hot water, high accumulation of boiler scale. Tab.3 Water temperature for various settings of temperature control knob. 25.07.2014 ZUG ELEKTROMET...
- Page 11 By ensuring the proper disposal you protect the environment. In order to obtain more detailed information regarding the recycling of this product please contact your waste disposal service or the shop where you have purchased this product. 25.07.2014 ZUG ELEKTROMET...
- Page 12 25.07.2014 ZUG ELEKTROMET...
- Page 13 25.07.2014 ZUG ELEKTROMET...
- Page 14 25.07.2014 ZUG ELEKTROMET...
- Page 15 25.07.2014 ZUG ELEKTROMET...
- Page 16 25.07.2014 ZUG ELEKTROMET...
Need help?
Do you have a question about the EJK mini and is the answer not in the manual?
Questions and answers