Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zodiac Diag box
Summary of Contents for Zodiac Diag box
- Page 2 • Do not spray insecticide or any other chemical (inflammable or non-inflammable) in the direction of the appliance, as this could damage the body and cause a fire. • Zodiac® Heat pump, filtration pump and filter appliances are compatible with most commonly used pool water treatment systems.
-
Page 3: Table Of Contents
• Keep these documents for future reference and pass them on throughout the device's service life. • Distributing or modifying this document in any way without authorisation from Zodiac® is prohibited. • Zodiac® is constantly developing its products to improve their quality; therefore, the information contained in this document may be modified without notice. -
Page 4: Package Content
Depending on your needs (and the appliance to be inspected), you may carry out 2 types of test: - Quick Test: This is a "simplified" test using the Diag Box tool only (may be carried out in the field, for example). -
Page 5: Vortex™ 1 Test (Robot)
Lazernaut, Cybernaut™ NT (>2010) Robot (via robot control box: $3.1) YELLOW adaptor ™ 4. Vortex™ 1 Test (Robot) Vortex 1 robot test Connect the Diag Box Connect the robot to the Diag Dia6 Box using the red adaptor Press Test “Cleaner” then “Start/Stop”... -
Page 6: Tornax, Cyclonx™ And Vortex™ (Except Vortex™1) Complete Test
5. TornaX, CyclonX™ and Vortex™ (except Vortex™1) Complete Test 5.1 Testing the robot TornaX, Vortex™, CyclonX™ robot test - Connect the Diag Box - Connect the robot to the Diag Box using the Dia6 grey adaptor for the CyclonX™, and floating cable for TornaX/ Vortex™... - Page 7 TornaX/ CyclonX™/ Vortex™ control box test 5.2 Testing the control box - Connect the control box - Connect the Diag Box Dia6 - Connect the control box to the Diag Box with the blue (CyclonX) or green (TornaX, Vortex) adaptor Press “Ebox” then “Start/ test Stop”...
- Page 8 5.3 Motor unit (CyclonX™, Vortex™) CyclonX™/ Vortex™ Motor unit test Connect the Diag Box Dia6 Connect the motor unit to the Diag Box with the brown adaptor Press “Cleaner” Test then “Start/ Stop” Change the TEST motor unit Fail- aT...
-
Page 9: Lazernaut, Cybernaut™ Nt (>2010) Test (Robot)
6. Lazernaut, Cybernaut™ NT (>2010) Test (Robot) - Connect the robot control box to the robot - Connect the Diag Box Dia6 - Connect the robot control box to the Diag Box using the yellow adaptor test Press “Cleaner” then “Start/ Stop”... -
Page 10: Remote Control Test : Depending On The Vortex™ Model
8. Full Test: enhanced mode (with Full Test Software application) 8.1 Downloading Full Test Software Before you use the tool for the first time, download the Full test Software application from: www.zodiac-poolcare.com • Access your Professional area • Open the Care Center section, the download Full Test Software 8.2 Start-up... -
Page 11: Product Conformity
9. Product conformity This appliance has been designed and built according to the following standards: Low voltage directive: 2006/95/EC Electromagnetic compatibility directive: 2004/108/EC EN 55014-1: 2000 +A1:2001 +A2:2002 ; EN 55014-2: 1997 +A1:2002 EN 60335-1: 2002 + A1:2004 + A2:2006 +A11:2004 + A12:2006 ; EN 60335-2-41: 2003 + A1:2004 Relative to which it is compliant.