Roban EC-130 Manual

Hide thumbs

page of 48

/ 48
Bookmarks

Quick Links

Download this manual

800 size EC-130

including

SM2.0/HSM-800 mechanics

Manual

CCPM SCALE RC HELIKOPTER

INCLUDING FENESTRON

Table of Contents

Need help?

Do you have a question about the EC-130 and is the answer not in the manual?

Questions and answers

Summary of Contents for Roban EC-130

Page 1 800 size EC-130 including SM2.0/HSM-800 mechanics Manual CCPM SCALE RC HELIKOPTER INCLUDING FENESTRON...
Page 2 Super Scale 800 Manual – EC-130 Release 1.0 - Dezember 2019 Roban Model Limited No 28, Liuchongwei 2 Industrial Zone, Wanjiang 523051 Dongguan (GD) - PRC Copyright@2020 - Roban Model Limited – all rights reserved...
Page 3: Specifications
Please read this user manual carefully, it contains instructions for the correct assembly of the model. Please refer to the web site www.robanmodel.com for updates and other important information. Thank you for your purchase, and have a great time with your Compactor! Roban Limited Copyright@2020 - Roban Model Limited – all rights reserved...
Page 4: Important Notes
FENESTRON OPERATION The Roban fenestron unit provides sufficient thrust to cope with any flight situation above a main rotor rpm of 1000 r/min. We have implemented our clients desire to be able to fly realistically at a low head speed. However, and due to the physical layout of the fenestron much higher required controlling forces are required compared to a typical RC helicopter tail rotor.
Page 7: Additional Components Required
ADDITIONAL COMPONENTS REQUIRED TOOLS, LUBRICANTS, ADHESIVES *Electric Motor: *Generic pliers 12S – 450KV 750MX, or similar *Hexagonal driver, size 1.5, 2, 2.5, 3, 4mm pinion shaft diameter 6mm *4mm T-Wrench *Speed controller: *5.5mm Socket wrench (for M3 nuts) minimum 120A to be safe *8mm Hex fork wrench (for M5 nuts) *Batteries: 10-12S 4000-5000mAh *Medium threadlocker (eg.
Page 8 Assembly Scale Fuselage Prior to installing the mechanics into the fuselage, please prepare the fuselage according to the following steps. Installation into the fuselage most of the helicopter mechanic become inaccessible Remove the front canopy. It is secured by screws, which are accesible fromt the side doors.
Page 9 Insert the spacers (21) into the spoiles (49) as shown, and secure with epoxy. Make sure to adjust them properly. Insert the joiner (20) into one side of the skid (19) as shown. Make sure the through holes line up as depicted. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 10 Then press the other skid (19) onto the joint as shown. Make sure that the through holes line up again! Secure the skids (19) with screws (39) as shown. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 11 Connect the red LED (54) with prolonging wires (55) und mount it from outside into the tail fin top above the fenestron duct. Route the wires all the way tot he front end oft he tail. We recommend securing it with dabs of hot melt glue. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 12 Then glue the LED cap (56) into the socket as show. Please make sure that you get the position light colors right. Route the LEDs (52) und (54) wires trough the fins as shown, make sure of correct color on left and right side. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 13 Make sure to take your time to align the tail wings correctly before gluing them into the tail boom. We recommend using masking tape to hold them in correct position while curing the resin. Secure the wires with dabs of hot melt glue. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 14 Connect the light of the main panel (58) e.g., it’s plug to the center panel (59) as shown. Then attach the mid panel with glue onto the center panel. The driver unit can be run on voltages from 5 to 12V DC. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 15 Then install all cockpit components into the floor board using epoxy glue, parts 58 through 64. Make sure the instrument LED system is connected and wires routed properly. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 16: Step 2 - Tail Boom
Assembly of Mechanics The mechanics are almost entirely preassembled and split up into four sections: rotorhead, main frame, tail frame and tail tube. Prior to the installation into the scale fuselage, the mechanics have to be entirely assembled, electronic components installed, adjusted and tested.
Page 18 Step 5 – Adjust swashplate linkages The linkages from the L-Levers to the swash plate have to be set at correct length. Distances are uniball center to uniball center: 1=35mm Step 6 – Motor and Belt installation In order to install the motor, you must first disassemble one of Mount the motor as shown using washers and screws onto the the side frames in order to have access to the mounting screws motor mount (70-00066).
Page 19 Secondary Motor Support Certain motors with 25mm mounts and long output shafts can be outfitted with a secondary motor shaft bearing. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 20 Step 7 – Electrical Wiring and Setup The mechanics have to be fully electrically setup and adjusted prior to installation into the fuselage. As the use of a 12S ATTENTION ! (44.4V) setup is necessary, we strongly recommend to run the control equipment on a separate 2S Lipo battery and BEC for When using the a pitch gauge to adjust correct CP travels, security reasons.
Page 21 Step 8 – Insert mechanics into fuselage Insert the mechanics from the front as shown. The fenestron and the tail need to be adjusted properly before the main frame can be fixed into the fuselage. First attach the tail boom onto the fuselage and align it properly. Then drill six holes evenly distributed using a 1,5mm drill through both tail boom and fuselage.
Page 22 Attach the spacer (12) onto the clamp (10) with a bit of CA glue as shown. Then install the clamp with screws (24) onto the tail boom. Only tighten the screws as much as necessary to prevent it from being completely loose. Then attach the tail boom, but not completely. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 23 Adjust the fen / tail boom to be centered in its duct, whist the tail boom and fuselage are fully engaged. Once adjusted, tighten the three screws on the clamp plate. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 24 Then tighten the screws on the duct clamp as well. After aligning everything properly, secure the mechanics with screws (39) as shown into the fuselage. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 25 Glue the footrest holders (51) onto the footrest (18) as shown. Then drill holes into the spoilers (50) in order to glue them in as well. Makes sure to align properly! Copyright@2020 - Roban Model Limited – all rights reserved...
Page 27 Please be realistic when assessing your piloting skills, because a scale helicopter is heavy and hence much less agile in response than any 3D helicopter. Keep this comparison in mind: if you can’t swim and you dive into deep water, the chances are that you will drown. Copyright@2020 - Roban Model Limited – all rights reserved...
Page 43: Appendix C - Ersatzteilliste
Unterteil 1-JJ-70-00030 Ball head Kugelkopf 1-JJ-70-00031 Washer 2x8x1 Washer 2x8x1 1-JJ-70-00032 Screw M2x6 Screw M2x6 RCH-70-022 1-JJ-70-00003 Rotorhead top Rotorkopf oben 1-JJ-70-00004 Rotorhead bottom Rotorkopf unten RCH-70-023 1-JJ-70-00001 Rotorhead Cap Rotorkopfkappe Copyright@2020 - Roban Model Limited – all rights reserved...
Page 44 Heckservoklammer RCH-70-043 1-JJ-70-00102 Gear 1M 30T Zahnrad 1M30T RCH-70-044 1-JJ-70-00103 Tail pushrod 702mm Gestänge 702mm RCH-70-045 1-JJ-70-00104 Tail support holder Strebenaufnahme 1-JJ-70-00105 Bolt 1.5x7.8 Bolzen 1.5x7.8 1-JJ-70-00106 Tail support rod Heckstrebe Copyright@2020 - Roban Model Limited – all rights reserved...
Page 45 1-JJ-70-00055 Bearing 12x24x6 Kugellager 12x24x6 RCH-70-074 1-JJ-70-00056 Bearing 10x19x5 Kugellager 10x19x5 RCH-70-075 1-JJ-70-00081 Nylon Nut M2.5 Nylon Nut M2.5 RCH-70-076 1-JJ-70-00084 Screw M2.5x8 Screw M2.5x8 RCH-70-077 1-JJ-70-00085 Screw M2.5x20 Screw M2.5x20 Copyright@2020 - Roban Model Limited – all rights reserved...
Page 46 1-JJ-70-00129 Nylon Nut M2 Nylon Nut M2 RCH-70-108 1-JJ-70-00141 Tail spindle Heckrotor Welle RCH-70-109 1-JX-47-00115 Rotor hub 3 blade Rotorkopf 3 Blatt RCH-70-110 1-JX-47-00103 Rotor hub 4 blade Rotorkopf 4 Blatt Copyright@2020 - Roban Model Limited – all rights reserved...

Roban EC-130 Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Roban EC-130

Summary of Contents for Roban EC-130

Page 3: Specifications

Page 4: Important Notes

Page 7: Additional Components Required

Page 16: Step 2 - Tail Boom

Page 28: Appendix A - Explosion Drawings

Page 43: Appendix C - Ersatzteilliste