Halton Max Ultra Circular Quick Manual For Commissioning
Hide thumbs
Also See for Max Ultra Circular:
Related Manuals for Halton Max Ultra Circular
Summary of Contents for Halton Max Ultra Circular
- Page 1 Halton Max Ultra Circular (MUC) - Quick guide for commissioning Enabling Wellbeing All rights reserved ©Halton...
-
Page 2: Table Of Contents
Halton Max Ultra Circular (MUC) - Quick guide for commissioning Contents 1 Introduction ................................. 3 1.1 About this document ............................3 1.2 Copyright and disclaimers ..........................3 1.3 Summary of changes ............................3 1.4 Contact information ............................3 2 Product description ..............................4 2.1 Overview ................................ -
Page 3: Introduction
Halton disclaims any and all liability related to this document. Halton gives no explicit or implied warranties in terms of this document. Any permitted use of the information included herein is at your own risk. Halton may amend or replace the information included in this document at its sole discretion without further notice and liability. -
Page 4: Product Description
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 2 Product description 2.1 Overview Fig. 1. Halton Max Ultra Circular (MUC) Circular airflow management damper using the ultrasound technique for airflow measurement. Application areas ▪ Variable (VAV) and constant (CAV) airflow control applications ▪... -
Page 5: Commissioning
Factory settings The airflow range for Halton Max Ultra Circular (MUC) is preset at the factory. The factory settings for the control signal and feedback signal are the same, but they can be configured individually. If the airflow range is not specified by the customer, the default factory settings are the following: ▪... -
Page 6: Airflow Control Panel
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 3.1.3 Airflow control panel Halton Max Ultra Circular (MUC) airflow controller has a control panel with a display and four pushbuttons. Fig. 2. Control panel The LCD display can show 16 characters in 2 lines. -
Page 7: Airflow Control Panel: Start-Up Views
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 3.1.4 Airflow control panel: start-up views Description Halton Default view LAC1.U01 Software version FW ver: 01 Measured airflow in m/s Air speed . m/s *{CtrlSig} Measured airflow in m Air flow (AF) -
Page 8: Modbus Rtu Communication
System (BMS) via Modbus RTU. With the Modbus register, you can read and configure parameter values. The default communication settings are Slave-ID 1, 115200bsp, O (Odd), 8 (bit), 1 (stop bit). You can change the communication settings on the correct parameter pages of the Halton Max Ultra Circular (MUC) controller: ▪... -
Page 9: Step By Step Instructions
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 3.2 Step by step instructions 3.2.1 Configuring basic controller settings in analog mode 1. Go to the controller parameter menu. 2. Set parameter CtrlMode to 'Analog'. 3. Check the values of the following parameters. If needed, modify the values. -
Page 10: Configuring Basic Controller Settings In Console Mode (Service Or Testing)
Halton Max Ultra Circular (MUC) - Quick guide for commissioning ▪ Baud rate (Baud) ▪ Possible values: 4k8 / 9k6 / 14k4 / 19k2 / 38k4 / 56k0 / 57k6 / 115k2 ▪ Default: 115k2 ▪ Parity (Pr ) ▪ Possible values: None / Even / Odd ▪... -
Page 11: Rebooting The Controller
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 3.2.5 Rebooting the controller 1. Go to the controller parameter menu. 2. Press the left arrow button, the right arrow button, and the OK button at the same time for 2 seconds. -
Page 12: Technical Reference Data
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 5 Technical reference data 5.1 Controller connections Connection diagram Fig. 4. Halton Max Ultra Circular (MUC) connection diagram Terminals Terminal Name Comment Ground 24 V DC/AC Power supply input Ground... -
Page 13: Parameters
Halton Max Ultra Circular (MUC) - Quick guide for commissioning 5.2 Parameters 5.2.1 Halton Max Ultra Circular (MUC) installation cases Value of Sensor Safety distance Installation case parameter position SelectDuctType > 7D 1D..7D 3D..7D Outwards 5D..7D Inwards 5D..7D Side 5D..7D... - Page 14 Halton Max Ultra Circular (MUC) - Quick guide for commissioning Value of Sensor Safety distance Installation case parameter position SelectDuctType Outwards 5D..7D Inwards 5D..7D Side 5D..7D Outwards 5D..7D Inwards 5D..7D Side 5D..7D All rights reserved ©Halton...