Advertisement
Quick Links
Operation Manual
Sliding Door System Set
61811, 61812
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Summary of Contents for XPOtool 61811
- Page 1 Operation Manual Sliding Door System Set 61811, 61812 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly.
- Page 2 To allow for a smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods. Returns Department WilTec Wildanger Technik GmbH Königsbenden 28 52249 Eschweiler E-mail: service@wiltec.info Tel: +49 2403 55592–0 Fax: +49 2403 55592–15 https://www.XPOtool.com Item 61811, 61812 Page 2 The Tool Experts 05 2022-1...
- Page 3 Always use the door handle to close the door. Note! Use of excessive force to open and close the door(s) can damage the item. Always hold the handle and open and close the door(s) gently. https://www.XPOtool.com Item 61811, 61812 Page 3 The Tool Experts 05 2022-1...
- Page 4 Item 61811, 61812 Page 4 The Tool Experts 05 2022-1...
- Page 5 This makes it easier for you to find the centre of the rail holes so that you can ( / ) then attach the rail to the wall. https://www.XPOtool.com Item 61811, 61812 Page 5 The Tool Experts 05 2022-1...
- Page 6 Slit the door on the underside with a suitable tool (7 mm wide and 20 mm deep). The slot is de- signed so that the door can run over the floor guide. https://www.XPOtool.com Item 61811, 61812 Page 6 The Tool Experts 05 2022-1...
- Page 7 Screw the hex bolts through the back of the door. Do not forget the washers. 2. Hold the hexagon head bolts with a wrench and tighten the cap nuts by hand. https://www.XPOtool.com Item 61811, 61812 Page 7 The Tool Experts 05 2022-1...
- Page 8 2. Also attach the other anti-jump disc next to the other steel bracket. Then screw both discs tight. These can prevent the door from jumping out of the rail. https://www.XPOtool.com Item 61811, 61812 Page 8 The Tool Experts 05 2022-1...
- Page 9 Step 11 Tilt the door slightly, lift it onto the rail and care- fully place both wheels with the grooves on top of the rail guide. https://www.XPOtool.com Item 61811, 61812 Page 9 The Tool Experts 05 2022-1...
- Page 10 8. Repeat steps 1–3 and 1–4. Then, hold the floor guide and attach it securely by tightening the screws with a cross-head screwdriver. 9. The installation of the fitting is now com- plete. https://www.XPOtool.com Item 61811, 61812 Page 10 The Tool Experts 05 2022-1...
- Page 11 Important Note: Reprinting, even in part, and any commercial use, including parts of the manual, only with the written consent of WilTec Wildanger Technik GmbH. https://www.XPOtool.com Item 61811, 61812 Page 11 The Tool Experts 05 2022-1...
Need help?
Do you have a question about the 61811 and is the answer not in the manual?
Questions and answers