Advertisement
Quick Links
Owner's Manual
Fletcher Saber™ 250-A
For Accurate and Efficient Saw Tooth Hanger Installation
The Fletcher-Terry Company
65 Spring Lane • Farmington, CT USA 06032-3311
Tel 860.677.7331 or 800.843.3826 • Fax 860.676.8858 • www.fletcher-terry.com
customerservice@fletcher-terry.com
Form 032404
Advertisement
Summary of Contents for Fletcher-Terry Fletcher Saber 250-A
- Page 1 Owner’s Manual Fletcher Saber™ 250-A For Accurate and Efficient Saw Tooth Hanger Installation The Fletcher-Terry Company 65 Spring Lane • Farmington, CT USA 06032-3311 Tel 860.677.7331 or 800.843.3826 • Fax 860.676.8858 • www.fletcher-terry.com customerservice@fletcher-terry.com Form 032404...
- Page 2 Product Warranty The Fletcher-Terry Company warrants the machine purchased to be free from defects in parts and workmanship for (2) two years from the date of purchase. The Fletcher-Terry Company warrants that it will repair or replace any such defective machine or replace parts, providing the machine has been under normal use and service and the defective part or machine is returned to The Fletcher-Terry Company at the purchaser’s expense.
- Page 3 Contact a Fletcher-Terry Customer Service Representative for replacement labels or parts. ÿ Only use the parts, supplies, and accessories that are recommended by Fletcher-Terry. ÿ Use care when loading the hanger strips onto the hanger guide, making sure that you do not inadvertently activate the T-bar switch.
- Page 4 If anything is missing, please contact a Fletcher-Terry Customer Service Representative at 800.843.3826, at 860.677.7331, or customerservice@fletcher-terry.com. ÿþýü ú...
- Page 5 VIEW A: FROM RIGHT SIDE Figure 4 VIEW B: FROM THE FRONT Figure 5 VIEW C: FROM ABOVE Figure 6 ÿþýü ú...
- Page 6 Before assembling the machine, determine whether you will anchor the Saber 250-A to your work surface. Placing and securing the machine will be a matter of personal preference and it is left to the owner to decide how best to use the Saber.
- Page 7 Figure 8 With the machine properly placed (and Set the T-bar to a 2-inch depth setting. Do optionally mounted to the work surface), this by loosening the T-bar clamping knob raise the carriage to its uppermost position and moving the entire T-bar assembly until a on the tower.
- Page 8 Saber 250-A. The required hanger strips (part number 08-810) may be ordered Once the strip is loaded onto by contacting the Fletcher-Terry the guide, the operator Customer Service Department at pushes the strip forward 800.843-3826; outside the U.S., toward the front of the call 860.677.7331;...
- Page 9 ÿþ üûúùø÷û öõû ô÷úóû úòñ ðñïøùö öõû üúîõíòû The Saber 250-A requires the operator to determine three measurements before proper placement of a saw tooth hanger can be made: a. The width of the Figure 11 frame; b. The hanger’s placement from the top of the frame to the...
- Page 10 Example “a” Taking measurements and adjusting the Saber 250-A: A frame measures 10 inches across. After loosening the fence with Knob A, move the fence so ÿ A. How wide are the frames you will be processing? that the Centering Scale (Scale A) reads 10 inches.
- Page 11 Please Note: Let’s Review: While this manual uses non- ÿ You have read and metric measurements in all of its examples, the Saber 250-A understand the safety has both imperial and metric instructions listed scales. inside the front cover of this manual.
- Page 12 þ Once all three measurements (a, b, and c) have been taken and the machine has been readied with these measures being reflected on Scales A, B, and C, the operator is now ready to insert the saw tooth hanger. ÿþ...
- Page 13 T- Bar assembly of the Saber 250-A. Therefore, The Fletcher-Terry Company has designed an optional adapter that will accommodate such frames. The adapter is fitted on the T-Bar stop block on the T- Bar assembly.
- Page 14 ÿþ üûûú ùø÷öõ Using an Optional Foot Pedal. Use of the foot pedal is a matter of the personal preference of the machine operator. It is assembled according to the instructions enclosed with the item. þ ÷÷úûöõ üøø øõ Figure 13 Inserting Two Hangers Per Frame Using a Second Fence.
- Page 15 Saber 250-A to your existing air supply system. If the pneumatic drive still does not work properly, contact your Fletcher-Terry Customer Service Representative for further advice. There is insufficient air pressure. Pressure settings are not Check your company’s properly set.
- Page 16 A ¼” clearance is necessary to avoid trapping the frame. For assistance, contact The Fletcher-Terry Company Customer Service Department at 800.843.3826, 860.677.7331, or customerservice@fletcher-terry.com. ÿþýü úù...
- Page 17 ÿ The Saber 250-A is an Description Part Number efficient and reliable machine, designed to be operated Air Regulator 18-000 safely and maintained with Air Valve 18-001 minimal effort. Air Limit Valve 18-002 ÿ Keeping the work area clean and clutter-free will allow the Indexing Cylinder Assembly 18-003 operator to work quickly and...
Need help?
Do you have a question about the Fletcher Saber 250-A and is the answer not in the manual?
Questions and answers