Summary of Contents for PSB PSB-1688LF
- Page 1 USER’S MANUAL PSB-1688LF M1 PSB-1688LF For Socket 370 Full-size CPU Card With VGA / Sound / LAN...
- Page 2 PSB-1688LF Socket 370 Full-size Embedded Card With VGA / Dual LAN OPERATION MANUAL COPYRIGHT NOTICE This operation manual is meant to assist both Embedded Computer manufacturers and end users in installing and setting up the system. The information contained in this document is subject to change without any notice.
-
Page 3: Fcc Notice
Copyright Notice FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 4: Table Of Contents
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual ... System Specification ... Safety Precautions ... CHAPTER 2 HARDWARE CONFIGURATION Jumper & Connector Quick Reference Table ... Component Locations ... How to Set the Jumpers ... COM Port Connector ………………………………… RS232/422/485 (COM2) Selection ... - Page 5 Contents 2-32 Memory Installation ………………………………….. 2-33 LCD Connector ……………………………………… CHAPTER 3 SOFTWARE UTILITIES Introduction …………... VGA Driver Utility ………………………………….. Flash BIOS Update ... LAN Driver Utility …... Sound Driver Utility …………………………….……. Watchdog Timer Configuration ... CHAPTER 4 AWARD BIOS SETUP Introduction ...
-
Page 6: Chapter 1 Introduction
INTRODUCTION This chapter gives you the information for PSB-1688LF. It also outlines the System specification. Section includes: About This Manual System Specifications Safety precautions Experienced users can skip to chapter 2 on page 2-1 for Quick Start. CHAPTER Page:1-1... -
Page 7: About This Manual
1-1. ABOUT THIS MANUAL Thank you for purchasing our PSB-1688LF Socket 370 Full-size CPU Card equipped with VGA / LAN, which is fully PC / AT compatible. PSB-1688LF provides faster processing speed, greater expandability and can handle more task than before. This manual is designed to assist you how to install and set up the system. -
Page 8: System Specification
UNIVERSAL SERIAL BUS : Universal Serial Bus Connector on board. Supports up to 4 USB2.0 ports. BUS SUPPORT : External ISA/PCI BUS (PICMG Spec.); EPCI BUS External Compact Flash Bus. ′ PSB-1688LF USER S MANUAL Chapter 1 Introduction Page: 1-3... - Page 9 Two high speed 16550 Compatible UARTs with Send / Receive 16 Byte FIFOs. COM1 for RS232. COM2 for RS232/422/485. PARALLEL PORT : SPP, ECP, EPP Function. Bi-directional parallel port. HARDWARE MONITORING FUNCTION : Monitor Voltage, CPU Temperature and Cooling Fan. Page: 1-4 ′ PSB-1688LF USER S MANUAL...
- Page 10 DC Ampere: 6.1A. (P-III 1.266 GHz) DC Voltage: +12V, minimum +11.4V, maximum +12.6V. DC Ampere: 500mA. BOARD DIMENSION : 338.5mm x 122mm, 13.33” x 4.8” BOARD NET WEIGHT : 375 grams ′ PSB-1688LF USER S MANUAL Chapter 1 Introduction Page: 1-5...
-
Page 11: Safety Precautions
3. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. Page: 1-6 ′ PSB-1688LF USER S MANUAL... -
Page 12: Chapter 2 Hardware Configuration
HARDWARE CONFIGURATION ** QUICK START ** Helpful information describes the jumper & connector settings, and component locations. Section includes: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector’s Pin Assignments CHAPTER Page 2-1... -
Page 13: Jumper & Connector Quick Reference Table
Memory Installation ...…...………. LCD Connector …………………………………………. LCD1 Reserved Pin ……………………………………………. Page: 2-2 COM1, COM2 JP3 (18,20) JP3 (1,3,5) CPUFAN1 JUSB1, JUSB2 WOL1 VGA1 IDE1, IDE2 FDD1 LPT1 LAN1 JCF1 JCF2 JP13 ATXPWR1 PPCI1 DIMM1, DIMM2 JP8, JP10 ′ PSB-1688LF USER S MANUAL... -
Page 14: Component Locations
Chapter 2 Hardware Configuration 2-2. COMPONENT LOCATIONS PSB-1688LF Connector, Jumper and Component locations ′ Page: 2-3 PSB-1688LF USER S MANUAL... -
Page 15: How To Set The Jumpers
PIN1 & PIN2 to create one setting and shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. Page: 2-4 ′ PSB-1688LF USER S MANUAL... - Page 16 JUMPER DIAGRAMS JUMPER SETTINGS 2 pin Jumper close(enabled) ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration Jumper Cap looks like this 2 pin Jumper looks like this 3 pin Jumper looks like this Jumper Block looks like this Looks like this...
-
Page 17: Com Port Connector
All COM port’s pin 9 is selectable for RI, +5V and +12V. For more information, please refer to our “COM Port RI & Voltage Selection”. Page: 2-6 ASSIGNMENT RS-422 RS-485 RTS- RTS+ CTS+ CTS- PSB-1688LF USER COM1 ′ S MANUAL... -
Page 18: Rs232/422/485 (Com2) Selection
COM 2 Function RS-232 RS-422 RS-485 *** Manufactory default --- RS-232. To select RS422 or RS485, COM2 must be set at RI function. ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration Jumper Settings (pin closed) Open 1-2, 5-6, 7-8... -
Page 19: Keyboard Or Ps/2 Mouse Connector
The jumper settings are as follows: DEVICE TYPE KEYBOARD PS/2 MOUSE *** Manufactory default -- AT Keyboard Page: 2-8 ASSIGNMENT PS/2 Mouse MSDATA MSDATA 5VSB MSCLK MSCLK JUMPER SETTING (pin closed) DIN1 JUMPER ILLUSTRATION JP12 JP12 ′ PSB-1688LF USER S MANUAL... -
Page 20: External Keyboard Connector
2-10. HARD DISK DRIVE LED CONNECTOR JP3 (10,12) : Hard Disk Drive LED Connector The pin assignment is as follows : ASSIGNMENT HD LED + HD LED - ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration HDD_LED Page: 2-9... -
Page 21: External Speaker Connector
The pin assignment is as follows : ASSIGNMENT PW_LED PW_LED 2-13. ATX POWER BUTTON JP3 (13,15) : ATX Power Button The pin assignment is as follows : ASSIGNMENT PW_BN1 PW_BN2 Page: 2-10 EXT_SPEAKER POWER_LED POWER BUTTON ′ PSB-1688LF USER S MANUAL... -
Page 22: Irda Connector
Note: To clear CMOS data, user must power-off the computer and set the jumper to “Clear CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer. ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration JUMPER SETTING... -
Page 23: Cpu Fan Connector
+12V 2-17. UNIVERSAL SERIAL BUS CONNECTOR JUSB1: Universal Serial Bus Connector This connector can connect up to two USB port. The pin assignments are as follows: ASSIGNMENT USBP0− USBP0+ USBP1− USBP1+ Page: 2-12 CPUFAN1 JUSB1 ′ PSB-1688LF USER S MANUAL... -
Page 24: Wake-On-Lan Connector
This connector can connect up to two USB port. The pin assignments are as follows: ASSIGNMENT USBP2− USBP2+ USBP3− USBP3+ 2-18. WAKE-ON-LAN CONNECTOR WOL1: Wake-On-LAN Connector. The pin assignments are as follows: ASSIGNMENT 5VSB LWAKE ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration JUSB2 Page: 2-13... -
Page 25: Reset/Nmi/Clear Watchdog Selection
To clear NMI command, user should short the “Clear Watchdog” pin via push button. Page: 2-14 JUMPER SETTING (pin closed) ILLUSTRATION PSB-1688LF USER JUMPER JP11 JP11 JP11 ′ S MANUAL... -
Page 26: Vga Connector
2-20. VGA CONNECTOR VGA1 : VGA Connector The pin assignments are as follows: ASSIGNMENT GREEN BLUE 5VDDCDA HSYNC VSYNC 5VDDCCL ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration VGA1 Page: 2-15... -
Page 27: Hard Disk Drive Connector
Chapter 2 Hardware Configuration 2-21. HARD DISK DRIVE CONNECTOR IDE1: Hard Disk Drive Connector The PSB-1688LF possesses two HDD connectors, which support ATA-100. The pin assignments are as follows: ASSIGNMENT IDERST PDD7 PDD6 PDD5 PDD4 PDD3 PDD2 PDD1 PDD0 PDREQ... - Page 28 SDD4 SDD3 SDD2 SDD1 SDD0 SDREQ SDIOW# SDIOR# SIORDY SDDACK# IRQ15 SDA1 SDA0 SDCS#1 IDEACTS# ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration ASSIGNMENT SDD8 SDD9 SDD10 SDD11 SDD12 SDD13 SDD14 SDD15 PULL LOW S66 DETECT SDA2 SDCS#3 Page: 2-17...
-
Page 29: Floppy Disk Drive Connector
34-pin flat cable to attach the FDD on the board, and the other side is attaches two FDDs. The pin assignments are as follows : ASSIGNMENT Page: 2-18 ASSIGNMENT DENSEL# INDEX# MOTEA DRVB DRVA MOTEB STEP WDATA WGATE TK00 RDATA# SIDE1 DSKCHG PSB-1688LF USER ′ S MANUAL... -
Page 30: Printer Connector
As to link the Printer to the card, you need a cable to connect both DB25 connector and parallel port. The pin assignments are as follows : ASSIGNMENT ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration ACK1J BUSY1 SLCT1... -
Page 31: Lan Connector
ISOLATED GND ISOLATED GND ISOLATED GND ISOLATED GND 2-25. COMPACT FLASH POWER SELECTION JCF1: Compact Flash Power Selection. The selections are as follows: POWER SELECTION 3.3V Page: 2-20 JUMPER SETTING (pin closed) ILLUSTRATION PSB-1688LF USER JUMPER JCF1 JCF1 ′ S MANUAL... -
Page 32: Compact Flash Master/Slave Selection
Master Slave 2-27. ATX POWER SIGNAL CONNECTOR JP13 : ATX Power Signal Connector The pin assignments are as follows: ASSIGNMENT 5VSB PS_ON ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration JUMPER SETTING (pin closed) ILLUSTRATION close open JUMPER JCF2... -
Page 33: Power Connector
Chapter 2 Hardware Configuration 2-28. POWER CONNECTOR ATXPWR1: Power Connector The pin assignments are as follows: ASSIGNMENT PW-OK 5VSB -12V PS-ON Page: 2-22 ATXPWR1 ′ PSB-1688LF USER S MANUAL... -
Page 34: Atx/At Power Selection
The default is set as ATX, if you wish to use the AT Power, you must remember to change the “Power Supply Type” in Advanced Chipset Features. And also you must disable the ACPI Function in the Power Management found in BIOS. ′ PSB-1688LF USER S MANUAL Chapter 2 Hardware Configuration JUMPER SETTING... -
Page 35: Epci Connector
Chapter 2 Hardware Configuration 2-30. EPCI CONNECTOR PPCI: You will find a EPCI connector in our PSB-1688LF. This connector is used to connect our daughter boards. The pin assignments are as follows: ASSIGNMENT AD10 AD12 AD14 AD16 AD18 AD20 AD22... -
Page 36: Eppci Irq Selection
2-31. EPPCI IRQ SELECTION JP14: EPPCI IRQ Selection The selections are as follows: SELECTION PCI_IRQB PCI_SERIRQ 2-32. MEMORY INSTALLATION PSB-1688LF CPU Card is enhanced with two DIMM socket. DRAM BANK CONFIGURATION DIMM 1 DIMM 2 128MB 128MB 256MB 256MB 512MB 512MB ′... -
Page 37: Lcd Panel Connector
FPD18 FPD23 FPD19 FP_VCC5 GFPVS GFPDEN GFPHS GFPCLK FP_VCC3 FP_VCC3 ENBKL ENAVEE Page: 2-26 ASSIGNMENT FP_VCC5 FPD0 FPD8 FPD1 FPD9 FPD2 FPD10 FPD3 FPD11 FPD4 FPD12 FPD5 FPD13 FPD6 FPD14 FPD7 FPD15 VCC12 VCC12 PSB-1688LF USER LCD1 ′ S MANUAL... - Page 38 SOFTWARE UTILITIES This chapter comprises the detailed information of VGA driver, LAN driver, sound driver, and Flash BIOS update. It also describes how to install the watchdog timer configuration. Section includes: VIA 4 IN 1 Service Pack Driver VGA Driver Utility Flash BIOS Update LAN Driver Utility USB 2.0 Chipset Software Installation Utility...
- Page 39 Chapter 3 Software Configuration 3-1. INTRODUCTION Enclosed with our PSB-1688LF package is our driver utility, which may comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc user, you will only need some of the files contained in the CD ROM disc,...
-
Page 40: Vga Driver Utility
3-3. VGA DRIVER UTILITY The VGA interface embedded with our PSB-1688LF can support a wide range of display mode, such as SVGA, STN, TFT ...etc. You can display CRT, LVDS and PanelLink simultaneously with the same mode. ′ PSB-1688LF USER... -
Page 41: Flash Bios Update
Utility Disk for system BIOS and VGA BIOS update. 3-4-2. To update VGA BIOS for LCD Flat Panel Display: As PSB-1688LF user, you have to update the VGA BIOS for your specific LCD flat panel you are going to use. For doing this, you need two files. - Page 42 (C) Award Software 2000 All Rights Reserved F1: Reset F10: Exit Please reset or power off the system, and then the Flash BIOS is fully implemented. ′ PSB-1688LF USER S MANUAL Chapter 3 Software Configuration FLASH MEMORY WRITER v7.XX Flash Type - MXIC 29F004T /5V File Name to Program: B88bxxxx.bin...
-
Page 43: Lan Driver Utility
Chapter 3 Software Configuration 3-5. LAN DRIVER UTILITY 3-5-1. Introduction PSB-1688LF Embedded Board is enhanced with LAN function that can support various network adapters. Installation programs for LAN drivers are listed as follows: 3-5-2. Installation Procedures of LAN Driver 1. Install LAN Driver to Windows 98SE/2000/XP Executing Windows 98SE/Windows 2000/Windows XP, it will auto- detect your system configuration and find the adapter hardware. -
Page 44: Lan Driver Utility
Ethernet ID. Last step to select OK and close NETWORK SETUP. Select SKIP if only one adapter is installed on this computer. For more information on installation procedure, please refer to TXT directory found on LAN DRIVER UTILITY. ′ PSB-1688LF USER S MANUAL Chapter 3 Software Configuration Page:3-7... - Page 45 6. Select “Driver”. 7. Click “Install” to install the driver. 8. Follow the instructions on the screen to complete the installation. 9. Click “Finish” after the driver installation is complete. Page:3-8 “System” wizard PSB-1688LF USER control panel. (Click ′ S MANUAL...
-
Page 46: Watchdog Timer Configuration
I/O port 441H, the system will run the command to stop the Watchdog function. In PSB-1688LF watchdog function, you must write your program so when it writes I/O port address 443 for enable watchdog and write I/O port address 441 for disable watchdog. - Page 47 Chapter 3 Software Configuration ′ Page:3-10 PSB-1688LF USER S MANUAL...
- Page 48 AWARD BIOS SETUP This chapter shows how to set up the Award BIOS. Section includes: Introduction Entering Setup The Standard CMOS Features The Advanced BIOS Features The Advanced Chipset Features Integrated Peripherals Power Management Setup PNP/PCI Configuration PC Health Status Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults...
-
Page 49: Introduction
4-1. INTRODUCTION This chapter will show you the function of the BIOS in managing the features of your system. The PSB-1688LF Dual Socket 370 Full-sized CPU Card is equipped with the BIOS for system chipset from Award Software Inc. This page briefly explains the function of the BIOS in managing the special features of your system. -
Page 50: Entering Setup
You may use the cursor the up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen. ′ PSB-1688LF USER S MANUAL Phoenix – Award BIOS CMOS Setup Utility ►Frequency/Voltage Control... -
Page 51: The Standard Cmos Features
[None] [None] [Pioneer DVD-ROM ATAP] [1.44M, 3.5 in.] [None] [EGA/VGA] [All, But Keyboard] 640K 1014784K 1015808K F6:Fail-Safe Defaults CMOS Setup screen Item Help Menu Level ► Change the day, month, year and century F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... - Page 52 Auto: The BIOS automatically determines the optimal mode. Normal: Maximum number of cylinders, heads, sectors supported are 1024, 16 and 63. Large: For drives that do not support LBA and have more than 1024 cylinders. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Page: 4-5...
- Page 53 Enhanced Graphics Adapter/Video Graphics Array. For EGA, VGA, SEGA, SVGA or PGA monitor adapters. Color Graphics Adapter, power up in 40 column mode. Color Graphics Adapter, power up in 80 column mode. Monochrome adapter, includes high resolution monochrome adapters. ′ PSB-1688LF USER S MANUAL...
-
Page 54: Chapter 4 Award Bios Setup
1024 1024 1224 1224 1224 1024 1024 1024 1024 1024 1024 1024 1024 1024 1024 ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Heads V-P comp LZone 65535 65535 65535 65535 65535 65535 65535 0000 0000 65535 1023... -
Page 55: The Advanced Bios Features
IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... - Page 56 You may enable / disable this item to define whether the system will look for a floppy disk drive to boot at power-on, or proceed directly to the hard disk drive. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup If this function is enabled and someone...
- Page 57 The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt. The system will boot, but access to Setup will be denied if the correct password is not entered at the prompt. ′ PSB-1688LF USER S MANUAL...
- Page 58 VIDEO BIOS SHADOW: Determines whether video BIOS will be coped to RAM. However, it is optional depending on chipset design. Video Shadow will increase the video speed. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Page: 4-11...
-
Page 59: Advanced Chipset Features
Advanced Chipset Features [Press Enter] [Press Enter] [Press Enter] [Disabled] [Enabled] [Enabled] [16M] [CRT] [24 Bits1024x768] [Disabled] F6:Fail-Safe Defaults Chipset Features Setup Screen The chipset manages bus speed and Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... - Page 60 (DRAM). Do not change the value from the factory setting unless you install new memory that has a different performance rating than the original DRAMs. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup DRAM clock / Drive Control...
- Page 61 Page: 4-14 Phoenix – Award CMOS Setup Utility AGP & P2P Bridge Control [64M] [Audo] [Disabled] [Disabled] [Disabled] F6:Fail-Safe Defaults Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL...
- Page 62 PCI Master 0 WS Write PCI Delay Transaction ↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F5: Previous Values ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Phoenix – Award CMOS Setup Utility CPU & PCI Bus Control...
- Page 63 This field allows you to enable or disable IO channel check NMI. Before selecting this function, the user should check first that NMI function is enabled as described in chapter 2 (Reset/NMI/Clear Watchdog Selection). Page: 4-16 ′ PSB-1688LF USER S MANUAL...
-
Page 64: Integrated Peripherals
If bios setup menu item supports USB device boot, it will cause Win9x detects the same storages twice when the system is rebooted, and USB HDD will fail. Note: this cause just happen under Win9x, the phenomenon is a limitation. ′ PSB-1688LF USER S MANUAL Phoenix – Award CMOS Setup Utility Integrated Peripherals... - Page 65 Page: 4-18 Phoenix – Award CMOS Setup Utility VIA OnChip IDE Device [Enabled] [Enabled] [Enabled] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Auto] [Enabled] F6:Fail-Safe Defaults Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL...
- Page 66 2. USB Keyboard Support Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Phoenix – Award CMOS Setup Utility VIA OnChip PCI Device...
- Page 67 This item allows you to select the IR half/full duplex function. Page: 4-20 Phoenix – Award CMOS Setup Utility SuperIO Device [Enabled] [3F8/IRQ4] [2F8/IRQ3] [Normal] Hi, Lo Enabled Half IR-Rx2Tx2 [378/IRQ7] [SPP] EPP1.7 F6:Fail-Safe Defaults Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL...
- Page 68 Select a DMA channel for the parallel port for use during ECP mode. INIT DISPLAY FIRST: This item allows you to decide to active whether PCI Slot or on-chip VGA first. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Page: 4-21...
-
Page 69: Power Management Setup
Page: 4-22 Phoenix – Award CMOS Setup Utility Power Management Setup [Enabled] [User Define] [Disable] [Suspend -> Off] [V/H SYNC+Blank] [Instant - Off] [Off] [Press Enter] F6:Fail-Safe Defaults Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... - Page 70 Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has “hung”. The choices are Delay 4 Sec and Instant-Off. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Monitor will remain on during power saving modes.
- Page 71 Page: 4-24 Phoenix – Award CMOS Setup Utility IRQ/Event Activity Detect [OFF] [LPT/COM] [ON] [OFF] [Disabled] [Disabled] [Disabled] 0 : 0 : 0 [Press Enter] F6:Fail-Safe Defaults Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL...
- Page 72 IRQ4 (COM 1) • IRQ5 (LPT 2) • IRQ6 (Floppy Disk) • IRQ7 (LPT 1) • IRQ8 (RTC Alarm) ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup • IRQ9 (IRQ2 Redir) • IRQ10 (Reserved) • IRQ11 (Reserved) •...
-
Page 73: Pnp/Pci Configuration
[Enabled] [Enabled] F6:Fail-Safe Defaults Item Help Menu Level ► Select Yes if you are using a Plug and Play capable operating system Select No if you need the BIOS to configure non-boot devices F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... - Page 74 ASSIGN IRQ FOR VGA: This item Enable/Disable to assign IRQ for VGA. ASSIGN IRQ FOR USB: This item Enable/Disable to assign IRQ for USB. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup By choosing “manual”, you are allowed to Page: 4-27...
-
Page 75: Pc Health Status
Phoenix – Award CMOS Setup Utility PC Health Status [Disabled] 49˚C /111˚F 5273 RPM 1.72V 3.28V 4.94V 11.85V -12.28V - 4.99V 3.34V 5.40V [Disabled] F6:Fail-Safe Defaults PC Health Status Setup Screen Item Help Menu Level ► F7:Optimized Defaults ′ PSB-1688LF USER S MANUAL... -
Page 76: Frequency/Voltage Control
EMI. This benefit may in some cases be outweighed by problems with timing- critical devices such as a clock-sensitive SCSI device. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Phoenix – Award CMOS Setup Utility... -
Page 77: Load Fail-Safe Defaults
When you press <Enter> on this category, you get a confirmation dialog box with a message similar to the following: Load Optimized Defaults ( Y/N ) ? N Pressing "Y" loads the default values that are factory setting for optimal performance system operations. Page: 4-30 ′ PSB-1688LF USER S MANUAL... -
Page 78: Password Setting
Press the < Enter > key again and the password will be disabled. Once the password is disabled, you can enter Setup freely. ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup Enter Password: PASSWORD DISABLED!!! Press any key to continue... -
Page 79: Save & Exit Setup
<Del> key during boot up. Page: 4-32 ►Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Save to CMOS and EXIT Y/N)? Y ↑↓→← : Select Item Save Data to CMOS PSB-1688LF USER word etup Saving ′ S MANUAL... -
Page 80: Exit Without Saving
►Integrated Peripherals ►Power Management ►PnP/PCI Configura ►PC Health Status Esc : Quit F10 : Save & Exit Setup ′ PSB-1688LF USER S MANUAL Chapter 4 Award BIOS Setup ►Frequency/Voltage Control Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Quit Without Saving (Y/N)? N ↑↓→←... -
Page 81: Isa Bus Pin Assignment
EXPANSION BUS This appendix indicates the pin assignments. Section includes: ISA BUS Pin Assignment PCI BUS Pin Assignment APPENDIX Page: A-1... -
Page 82: Isa Bus Pin Assignment
SA14 -MASTER SA13 SA12 SA11 SA10 SA09 SA08 SA07 SA06 SA05 SA04 SA03 SA02 SA01 SA00 ASSIGNMENT SBHE LA23 LA22 LA21 LA20 LA19 LA18 LA17 -MEMR -MEMW SD08 SD09 SD10 SD11 SD12 SD13 SD14 SD15 ′ PSB-1688LF USER S MANUAL... -
Page 83: Pci Bus Pin Assignment
-12V INTB# INTD# REQ3# REQ1# GNT3# CLKA CLKB REQ0# +5V(I/O) AD31 AD29 AD27 AD25 C/BE3# AD23 AD21 AD19 ′ PSB-1688LF USER S MANUAL ASSIGNMENT ASSIGNMENT TRST# +12V AD17 C/BE2# IRDY# INTA# INTC# DEVSEL# CLKC LOCK# +5V(I/O) PERR# CLKD SERR# GNT1#... - Page 84 Appendix A Expansion Bus ′ Page: A-4 PSB-1688LF USER S MANUAL...
- Page 85 TECHNICAL SUMMARY This section introduce you the maps concisely. Section includes: Block Diagram Interrupt Map RTC & CMOS RAM Map Timer & DMA Channels Map I / O & Memory Map APPENDIX Page: B-1...
-
Page 86: Block Diagram
Page: B-2 SOCKET TERMINATOR CLE 266 VT8623 North Bridge V-LINK CLOCK BUFFER VT8235 outh ridge LPC SIO W83697HF H/W MONITOR CPU FAN Temperature PSB-1688LF USER CLOCK SYNTHESIZER ICS 94227 Terminator Moudles PCI/ISA WATCHING IT888F/BF KB/MS RTL8100BL ISA ROM ′ S MANUAL... -
Page 87: Interrupt Map
INTERRUPT MAP ′ PSB-1688LF USER S MANUAL Appendix B Technical Summary ASSIGNMENT System TIMER Keyboard Cascade Serial port 2 Serial port 1 Available Floppy Parallel port 1 RTC clock Available Available Available PS/2 Mouse Math coprocessor IDE1 IDE2 Page: B-3... -
Page 88: Rtc & Cmos Ram Map
Extension memory low byte Extension memory high byte Reserved for extension memory low byte Reserved for extension memory high byte Date Century byte Information Flag 34-3F Reserve 40-7f Reserved for Chipset Setting Data Page: B-4 ASSIGNMENT PSB-1688LF USER ′ S MANUAL... -
Page 89: Timer & Dma Channels Map
TIMER & DMA CHANNELS MAP Timer Channel Map : Timer Channel DMA Channel Map : DMA Channel ′ PSB-1688LF USER S MANUAL Appendix B Technical Summary Assignment System timer interrupt DRAM Refresh request Speaker tone generator Assignment Available Available Floppy... -
Page 90: I/O & Memory Map
Interrupt controller (Slave) DMA controller (Slave) Math coprocessor Hard Disk controller Parallel port-2 Graphics adapter controller Serial port-2 Net work ports Parallel port-1 Monochrome & Printer adapter EGA adapter CGA adapter Floppy disk controller Serial port-1 PSB-1688LF USER ′ S MANUAL...