Advertisement
4.1.
Fit the set screw (2) through the hole in cabinet (1) and secure using the lock nut (3).
4.2.
Fit one end of the hose (4) onto the set screw ensuring it is as far onto the set screw as
possible as shown in fig.3.
4.3.
Attach the sleeve (9) to the other end of the hose.
4.4.
Screw the adaptor (7) into the suction gun (6).
4.5.
Connect the adaptor (7) to the sleeve (9) using the lock nut (8) and tighten.
4.6.
Fit the air inlet (5) to the gun handle.
4.7.
Ensure all fittings have been correctly tightened and the kit is ready to use.
5. OPERATION
F
WARNING! Ensure that you read, understand and apply the safety instructions in Section 1 before use.
F
WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster.
F
WARNING! Ensure the air supply does not exceed 125psi (8.5 bar) while operating the unit.
5.1. Fill the cabinet with the required abrasive, checking to ensure it is clean and dry.
5.2. Attach an airline to the gun and press the trigger.
5.3. Before blasting unfamiliar material, spot test to ensure that damage/pitting will not occur to the material.
5.4. Use even passes of the blaster to remove material such as rust, body filler or other soft materials. Do not blast in any one area for more
than a few seconds at a time.
6. MAINTENANCE
Numbers in brackets refer to the item numbers in parts diagram.
F
WARNING! Disconnect from the air supply before performing any maintenance!
F
WARNING! Wear approved ear, eye, hand and respiratory protection when performing any maintenance.
F
WARNING! Ensure the air supply does not exceed 125psi (8.5 bar) while operating the unit.
6.1.
Changing the blasting medium.
6.1.1. It is not necessary to remove the blasting medium from the cabinet (1) after every use, however it must be cleaned out when a different
blasting medium is to be used
6.1.2. Remove the gun (6) from the hose (4) by loosening the lock nut (8).
6.1.3. Use a low pressure air line (10 psi) to blow through the hose.
6.1.4. When the cabinet (1) is clean, refit the gun (6) to the hose (4) and tighten the lock nut (8).
6.2.
Gun maintenance.
6.2.1. Remove the gun (6) from the hose (4) by loosening the lock nut (8).
6.2.2. Lubricate the gun with a few drops of good grade air tool oil, such as Sealey ATO500 or ATO1000, dripped into the air inlet (5).
6.2.3. Lubricate the plunger, between the trigger and the gun handle.
6.2.4. Refit the gun to the hose and tighten the lock nut.
6.2.5. Attach an airline to the gun and operate the blaster for a few seconds.
7. PARTS LIST & DIAGRAM
Issue:
1
Date: 011102
Declaration of Conformity
SHOT BLASTING KIT
SB993
97/23/EC Pressure Equipment Directive
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No responsibility is accepted for the incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your name and address, including postcode.
Sole UK Distributor,
Sealey Group,
Bury St. Edmunds, Suffolk.
We, the sole importer into the UK, declare that the product listed here is in conformity with the following standards and directives.
The construction file for this product is held by the Manufacturer and may be inspected, by a national authority, upon
request to Jack Sealey Ltd.
Signed by Mark Sweetman
For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products.
01284 757500
Item
Part No
Description
1
SB993-01
Cabinet
2
SB993-02
Set screw
3
SB993-03
Lock nut
4
SB993-04
Suction hose
5
SB993-05
Air inlet
6
SB993-06
Suction gun
7
SB993-07
Adaptor
8
SB993-08
Lock nut
9
SB993-09
Sleeve
10
SB993-10
Head cover
Date 1st November 2002
E-mail: sales@sealey.co.uk
01284 703534
Web: www.sealey.co.uk
fig.2
SB993 - 1 - 011102
Advertisement
