Table of Contents
Advertisement
Quick Links
45CC 18" GAS CHAINSAW
WARNING: This product can expose you to chemicals including LEAD,
CADMIUM and Di(2-ethylhexyl) phthalate (DEHP), which are known to the State
of California to cause cancer and birth defects or other reproductive harm. For
more information go to: www.P65Warnings.ca.gov
Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property
damage and/or personal injury. Please keep instructions for future reference.
For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.
For Customer Service:
Please call 877-713-3189 (Toll Free), or email: Support@fot-usa.com
*Actual product may vary slightly
97004
Advertisement
Table of Contents
Related Manuals for RidgeLine 97004
Summary of Contents for RidgeLine 97004
- Page 1 97004 45CC 18" GAS CHAINSAW WARNING: This product can expose you to chemicals including LEAD, CADMIUM and Di(2-ethylhexyl) phthalate (DEHP), which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to: www.P65Warnings.ca.gov *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.
-
Page 2: Specifications
IMPORTANT OPERATING INSTRUCTIONS SPECIFICATIONS SAFETY INSTRUCTIONS IMPORTANT! 1. Only allow users who have Engine Displacement: 45.1 cc When using equipment, a few read and understand this manual Bar Length: 14in. 18in. 20in. safety precautions must be operate this chainsaw. *Varies by different model 2. -
Page 3: Avoiding Kickback
Always begin cutting with the engine Chain Brake KICKBACK at full speed and with the saw The chain brake is designed to stop WARNING: Kickback is the housing resting against the wood. the chain from rotating in the event backward, upward or sudden of a kickback. -
Page 4: Adjusting The Chain Tension
2) Remove the clutch cover. 6) Place the chain drive links into the 3) Turn the screw to the right to (Figure 3) bar groove. increase the tension and turn it to the left to release tension. 7) Pull the guide bar forward to make sure all of the drive links are in 4) Using a screwdriver, move the the bar groove. -
Page 5: Operation Safety Instructions
6) Store the saw and fuel in an area Checking the Chain Brake free to move without contacting any where sparks or open flame will not object. The chain brake should be checked reach it. several times during use. The 1) Move the ON/OFF switch to the engine needs to be running while OPERATING INSTRUCTIONS... - Page 6 Remove all foreign objects from the As the tree begins to fall, stop and Important Operation Reminders tree where the cuts are going to be put down the saw and quickly get Allow the engine to reach full speed made. Plan a clear retreat path that away on your planned retreat path.
- Page 7 Overcutting is when the bottom of Overcutting is when the bottom of Make the second cut all the way Make the second cut all the way Important Safety Reminders Important Safety Reminders the saw is against the top of the log. the saw is against the top of the log.
-
Page 8: Air Filter Cleaning
move the filter into the correct Air Filter Cleaning Lubricating the sprocket tip position. Be careful not to damage the DO NOT clean the air filter in The sprocket tip on your new saw filter. gasoline or other flammable has been pre-lubricated in the solutions. - Page 9 4) Clean the oil holes and bar Chain Maintenance to coat the internal parts. Replace groove. spark plug. Sharpening 5) If the bar is burred, remove the Note: Store the unit away from Chain sharpening requires special burs with a flat file. water, sources of flame and sparks tools to ensure that the cutters are and in a cool, dry location.
-
Page 10: Troubleshooting Guide
Troubleshooting Guide Symptom Possible Cause(s) Corrective Action Ignition switch is not ON Turn ignition switch ON Reference digital starting section of this Engine is flooded manual Fuel tank is empty Fill tank with proper fuel mixture Engine will not start or will not stay running Spark plug is not working Install new spark plug... - Page 11 Troubleshooting Guide Set chainsaw on the ground and make sure chain brake is set to the disengaged position (pulled towards the rear handle). Pull the choke lever into the fully open position (all the way out). Squeeze throttle and set throttle lock button. Place right foot on rear handle securing the saw to the ground.
-
Page 12: Parts List
Parts List Part Description Part Description Chain Bar (varies by model No) Starter Assembly Saw Chain (varies by model No) Fuel Tank Cap Chain Tensioning Screw Rear Handle/Bootstrap Stop Claw Bar Cover Chain Brake Lever/Front Hand Guard Front Handle Brake Assembly Fixing Nut Starter Handle Spark Plug (under air filter cover) Chain Catch... - Page 13 Parts List A. Fuel Tank, Handle Part NO. Parts Description Quantity Fuel Tank Screw ST4.2x19 Fuel Cap Assembly Safety Guard A4-1 Fuel Cap "O" Ring A4-2 Fuel Cap A4-3 Dust Cover Screw M5x16 Long Anti-Vibration Seat Fuel Tank Anti-Vibration Block Fuel Filter Loaded Weight Block Fuel Tube Base...
- Page 14 B. Right Cover Assembly Part NO. Parts Description Quantity Screw ST4.2x9.5 Tensioner Cover Guide Block Brake Spring Plate Tensioning Gear Tensioning Screw Tensioning Block Pin 3x9 Main Pull-Rod Secondary Pull-Rod Brake Lever Brake Spring Brake Auxiliary Spring Split Washer 3 Front Guard Flat Washer（6x18x1 ）...
-
Page 15: Starter Assembly
C. Starter Assembly Part NO. Parts Description Quantity Screw M5x16 Starter Assembly Starter Cover C2-1 Starter Rope C2-2 Starter Handle C2-3 Easy Starter Main Coil Spring C2-4 Reel C2-5 C2-6 Easy Starter Assistant Coil Spring Starter Wheel C2-7 Flat Washer 5.4x16x1 C2-8 Screw St4.8x13 C2-9... - Page 16 E. Carburetor, Air Filter Part NO. Parts Description Quantity Air Filter Accelerator Rod Screw M5x39 Screw M5x52 Air Intake Carburetor Air Intake Flange Hot Start Backset Assembly E8-1 Hot Start Backset E8-2 Air Intake Tube Gasket E8-3 Dustproof Block Screw M5x12 Heat Insulation Spile F.
-
Page 17: Crankshaft, Piston
G. Crankshaft, Piston Part NO. Parts Description Quantity Woodruff Key M3*10 Needle Bearing Ring Crankshaft Needle Bearing 11X15X12.5 Piston Piston Ring Piston Pin Circlip Piston Pin H. Flywheel, Igniter Part NO. Parts Description Quantity Nut M8 Flywheel Assy Igniter Assy Screw Gb/T 70.1 M5*20 Igniter Sheath For Customer Service:... -
Page 18: Engine Assembly
J. Engine Assembly For Customer Service: Please call 877-713-3189 (Toll Free), or email: Support@fot-usa.com... -
Page 19: Parts Description
Parts List Part NO. Parts Description Quantity Oil Tank Cap Assembly J1-1 Oil Tank Cap J1-2 Oil Cap Packing Washer J1-3 Fuel Cap Retainer Screw M4x8 Oil Seal Protector Oil Seal Assembly J4-1 Oil Seal 15x35x5 J4-2 Oil Seal 15x28x5 Ring 35 Bearing 6202 Short Damping Block... - Page 20 K. Upper Cover, Air Filter Cover Part NO. Parts Description Quantity Air Filter Lock Nut Lock Nut Washer Air Filter Cover Shock Rubber Cushion Screw M5x16 Screw M5x14 Conversion Board Upper Cover Chain Catcher Screw ST4.8x16 Conical Spring Base Conical Spring Idle Adjusting Guide Dust Cover Plug...
-
Page 21: Bar And Chain
L. Bar and Chain Part NO. Parts Description Quantity Bar Cover Chain P. Packing Accessory Part NO. Parts Description Quantity Screwdriver File Socket Wrench Manual For Customer Service: Please call 877-713-3189 (Toll Free), or email: Support@fot-usa.com...
Need help?
Do you have a question about the 97004 and is the answer not in the manual?
Questions and answers