Advertisement
Quick Links
AbuseMarK
K LCD Adapter
Abu
useMa
arK LC
1. D
isplayPort co
nnector
2. 5
1‐pin FPC con
nnector for LC
3. U
SB connector
r for power o
4. Po
ower button
5. Po
ower/Status
LED
6. Ex
xternal 5V so
urce (see Ext
For functi
onality of Pow
wer button, s
page).
02/17/20
13
r Manual
CD Ad
dapte
CD
r firmware up
pdate
ernal Power s
section)
see the "LCD
Adapter firm
r (rev
v1)
ware feature
es and operation" section (
(last
Advertisement
Related Manuals for Abusemark LCD
Summary of Contents for Abusemark LCD
- Page 1 AbuseMarK K LCD Adapter r Manual useMa arK LC CD Ad dapte r (rev v1) 1. D isplayPort co nnector 2. 5 1‐pin FPC con nnector for LC CD 3. U SB connector r for power o r firmware up pdate 4. Po ower button 5. Po ower/Status LED 6. Ex xternal 5V so urce (see Ext ernal Power s section) ...
- Page 2 AbuseMarK K LCD Adapter r Manual nnecti ng ad dapter r to L CD Pa anel 1. C arefully lift up p lever on the e back of con nector 2. A lign FPC cable e with circuit (gold) side fa acing up, and push it into c connector 3. St top when cab ble reaches sh hown position n. Do not forc ce cable furth her into the co onnector 4. W While keeping cable aligned...
- Page 3 AbuseMarK K LCD Adapter r Manual proper r conn nectio on ex ampl Left image e: Cable not a aligned correc ctly, not fully inserted. Pow wering up like e this will like ely burn the p panel. Right ima ge: Cable inse erted circuit ( (gold) side do own, this is in correct. Exte ernal Powe er 5V sourc When arr anging many panels in arr ay, its easier to source a s ingle 5V conn nector for all panels and av void ...
- Page 4 AbuseMarK K LCD Adapter r Manual D Adap pter f firmw ware u upgrad de an ration Requir red softwa are TMicroelectro onics DFuSe U USB Device Fi irmware Upgr rade GUI: ttp://www.st t.com/web/en n/catalog/too ols/PF257916 6 or firmware u update on un supported or r niche OS (e x. Linux), on...
- Page 5 AbuseMarK LCD Adapter Manual LCD Adapter firmware features and operation When connected by USB or external 5V source, adapter defaults to full power on, with status LED glowing BLUE. One press on power button will switch to STANDBY mode, which turns off backlight, but keeps DisplayPort connection. This mode is used to keep power consumption lower, or to save backlight lifetime. In this mode, status LED is glowing RED. To fully turn off the adapter (including disconnect from DisplayPort signals), press the power button twice. ●→●→☀ (BLUE – full power on ‐> RED – standby ‐> Full power off (LED off) Since most common use case does not involve disconnecting from DisplayPort (as this would cause other monitors to flicker while display adapter is reconfiguring), if adapter is in standby mode for more than a few seconds, pressing the power button returns to Full power mode, turning on backlight. ●→●→Wait 2+ seconds→● (BLUE – full power on ‐> RED – standby ‐> if monitor is in standby for a few seconds, pressing Power again will go back to FULL power mode (BLUE LED). To change brightness, press and hold the power button for more than a second. This enters brightness control mode. In this mode, status led glowing cycles between 2 colors ‐ YELLOW means brightness DOWN adjustment, and PURPLE means brightness UP adjustment. Once in brightness adjustment mode, short clicks on power button will adjust brightness in steps up or down respectively. Hold power button again to switch to next mode, or to save. ●→●→●→● When required brightness is achieved, hold the button until status LED is glowing BLUE. This will save current brightness to non‐volatile memory. Other features may be added via firmware updates at a later time. This information is current as of 2014/02/17 02/17/2013 ...