Summary of Contents for M&M Sales Enterprises Geodesic Monkey Climber
- Page 1 USER MANUAL Assembly • Operation • Maintence • Safety Geodesic Monkey Climber • MM00191 M&M SALES Enterprises, inc. Dubuque, Iowa 877.242.0154 mandmsalesinc.com...
-
Page 2: Safety Instructions
Always provide supervision for children of all ages and skill levels. • Do not allow the player to use the Geodesic Monkey Climber™ when it’s wet or not properly installed. • Do not allow the player to damage the pole coatings. - Page 3 The data and information below are excerpted from the CPSC website and publication Outdoor Home Playground Safety Handbook (Publication #324*2005). The full version can be obtained by visiting http://www.cpsc.gov. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment.
-
Page 4: Parts List
GEODESIC MONKEY CLIMBER #MM00191 PARTS LIST PARTS LISTED CONTINUED ON NEXT PAGE... - Page 5 PARTS LIST – CONTINUED FROM PREVIOUS PAGE...
- Page 6 BEFORE ASSEMBLY --- • Measure the proper area for placement of the Geodesic Monkey Climber™ on a level, well- drained ground with proper loose-fill surfacing materials (refer to Safety section). • Do not place the Geodesic Monkey Climber™ over any hard surface such as concrete, asphalt, and packed earth.
-
Page 7: Assembly Steps
#A with a part #F (short bolt), a part #G, and two parts #H. Use the tools (parts I and J) to tighten them together. ATTENTION: Insert the bolt from the outside of the dome climber. That is, the nut should be inside on the first layer of the Geodesic Monkey Climber™. - Page 8 (b) Repeat until you finish assembling the 10 joints.
- Page 9 IMPORTANT: The following tips apply to all subsequent assembly steps. • Add all poles counterclockwise. • Insert all bolts (except bottom layer) from the inside of the dome climber and add the nut from the outside. That is, insert the part #E (long bolt) into the preformed hole, fix it with the part #H and the part #K.
- Page 10 (b) Move to the next joint, connect two parts #A (long blue pole) and one part #B (short green pole) counterclockwise with a part #E (long bolt), a part #H, and a part #K. Use the tools (parts I and J) to tighten them together as before. (c) Repeat until you finish assembling all the 10 joints.
- Page 11 STEP 4 - FINISH THE THIRD LAYER (a) Start from any one of the joints created by Step 3. Connect two parts #M (long pole in red bag) and one part #B with a part #E, a part #H, and a part #K. Use tools (parts I and J) to tighten together.
- Page 12 STEP 5 - FIX THE CENTRAL JOINT A central joint would come into being after you finish Step 4. Put a part #E, a part #H, and a part #K into the central point, tighten them with the tools (parts I and J). IMPORTANT: if you feel it is a bit difficult to finish assembling the last joint of each layer, slightly loosen the bolts of two adjacent joints.
- Page 13 #D (barrel nut) into the preformed hole, then tighten them with the tool part #I. NOTE: The gap of the grip should be next to the top pole as shown below. Congratulations! Your Geodesic Monkey Climber™ is completed! If you have any questions about the assemble, please email: sales@mandmsalesinc.com.
-
Page 14: Maintenance
• Repaint with non-lead-based paints if signs of oxidation and/or rust appear. • Store the Geodesic Monkey Climber™ in a dry area with good ventilation when it’s not in use. • Do not use any abrasive cleansers. Wipe dust and dirt with a soft, damp cloth.