1. Manuals
  2. Brands
  3. Allstar Manuals
  4. Door Opening System
  5. J & H Series
  6. Owner's manual

Allstar J & H Series Owner's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION AND
OWNER'S MANUAL
J & H SERIES JACKSHAFT COMMERCIAL
As of date of manufacture,
meets all ANSI/UL 325
Safety Requirements
for
Vehicular door operators
J & H
VEHICULAR DOOR OPERATORS
Serial #:
Date Installed:
Your Dealer:
READ THIS MANUAL
CAREFULLY BEFORE
INSTALLATION OR USE
SAVE THESE INSTRUCTIONS !

Advertisement

Table of Contents
loading

Summary of Contents for Allstar J & H Series

  • Page 1 INSTALLATION AND OWNER’S MANUAL J & H J & H SERIES JACKSHAFT COMMERCIAL VEHICULAR DOOR OPERATORS READ THIS MANUAL Serial #: Date Installed: CAREFULLY BEFORE Your Dealer: As of date of manufacture, INSTALLATION OR USE meets all ANSI/UL 325 Safety Requirements SAVE THESE INSTRUCTIONS ! Vehicular door operators...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Jackshaft Operator Applications.................. 3 Preparation ........................4 Figure 1 - Component Identification Pictorial.............. 4 Important Installation Warnings (Things To Do Before & During Installation) ..5 Table 1 - Component Identification Listing..............5 Installation Instructions .....................6-7 Figure 2 - Operator Footprint - J/H ................6 Figure 5 - Release/Hand Chain Wall Bracket Installation ...........

  • Page 3: Jackshaft Operator Applications

    The purpose MODEL J & H OPERATOR APPLICATIONS: of this booklet is to provide assembly, installation and operation information concerning Allstar Jackshaft operators are intended for commercial and Model J & H Commercial Vehicular Garage Door industrial use to raise or lower sectional overhead Operators and related Accessory Products.

  • Page 4: Preparation

    PREPARATION verify that it is the correct model for the intended WARNING application and that the voltage and phase are in accordance with electrical power provided at the job site. If the operator was ordered with the optional chain hoist, Model H, see that it ELECTRIC DOOR OPENERS ARE DESIGNED is so equipped.

  • Page 5: Important Installation Warnings (Things To Do Before & During Installation)

    Reinforcement Kit. b) at a minimum height of five feet • Allstar Models J and H are Commercial above the floor and; Vehicular Door Operators and as such are NOT recommended for pedestrian traffic. In...
  • Page 6 INSTALLATION INSTRUCTIONS SPRINGS, PULLEYS, CABLES AND MOUNTING HARDWARE USED TO BALANCE YOUR GARAGE DOOR ARE UNDER EXTREME TENSION AT ALL TIMES AND CAN CAUSE SEVERE INJURY OR DEATH IF DISTURBED. WARNING DO NOT ATTEMPT ADJUSTMENT. life of the bearings. If there is any flexibility in the system due igure 6, page 8 illustrates several positions suitable for to construction of the surface supporting the operator or mounting the operator;...
  • Page 7 INSTALLATION INSTRUCTIONS CHAIN HOIST AND FLOOR DISCONNECT INSTALLATION If the operator is furnished with a chain hoist (Model H), pass the hand chain over the chain wheel and through the chain guides on the operator clutch shaft (opposite end from the large pulley). Fasten the ends of the chain together by opening and re-closing one link using two pairs of pliers.
  • Page 8 FIGURE 6 - OPERATOR MOUNTING POSITIONS Center Right Side Left Side Mount Mount Mount Direct Ceiling Couple Mount Ceiling Mount Wall Mount Wall Mount Figure 6 100719...
  • Page 9 FIGURE 7 and 7A- OPERATOR DIMENSIONS 107841 Figure 7 - Dimensions Model H 108203 Figure 7A - Dimensions Model J...

  • Page 10: Installation Instructions

    INSTALLATION INSTRUCTIONS Manually raise the door to a nearly open position. WARNING Depress the limit nut retaining bracket (F) so it disengages from the slots in the limit nuts. Turn the OPEN limit nut (E) on TO AVOID RISK OF ENTRAPMENT AND the shaft until it engages both the Single Button Selector switch POSSIBLE DAMAGE TO THE DOOR AND (C) and the Open Limit Switch (D).

  • Page 11: Electrical Wiring Instructions

    WIRING THE OPERATOR. INSTRUCTED TO DO SO. ENSURE DOORWAY IS CLEAR BEFORE STARTING TESTING OF WARNING: Allstar's J & H Series operators have been UNIT. designed and constructed for use with voltages from 115 Volts AC to 480 Volts AC, in single or three phase. Check the door reversing edge components.
  • Page 12 PNEUMATIC DOOR EDGE INSTALLATION - FIELD WIRING Figure 9 Figure 10...

  • Page 13: Operation And Adjustment Instructions

    OPERATION & ADJUSTMENT INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS FOR OWNER TO REDUCE THE RISK OF SEVERE INJURY OR WARNING DEATH: READ AND FOLLOW ALL INSTRUCTIONS! • NEVER let children operate or play with door controls. Keep the Remote Control away from children.

  • Page 14: Wiring Types

    WIRING TYPES If pressure is released door will reverse to full open NOTE: Check the marking on the operator outer carton and the wiring diagram on the inside control box cover for the wiring To Stop- Door will stop when the opener activates a limit switch type.

  • Page 15: Clutch Adjustment

    OPERATION & ADJUSTMENT INSTRUCTIONS CLUTCH ADJUSTMENT REQUIRED TO THE DOOR, DOOR SPRINGS OR DOOR WARNING OPERATOR MUST BE PREFORMED BY A QUALIFIED PROFESSIONAL DOOR INSTALLER. RISK OF ENTRAPMENT THAT MAY RESULT The clutch pad will wear during normal operation and should be IN SERIOUS PERSONAL INJURY OR DEATH.

  • Page 16: Brake Adjustment

    OPERATION AND ADJUSTMENT INSTRUCTIONS BRAKE ADJUSTMENT The solenoid operated brake may require occasional adjustment. Adjustment is necessary if door tends to drift 107103 downward after reaching the open limit. Follow the instructions below and use Figure 12 as a guide. (1) Loosen shoe adjusting screw and bottom bracket arm of solenoid.

  • Page 17: Maintenance

    MAINTENANCE Normally, very little maintenance is required. A monthly visual CAUTION inspection must be made for loose or missing hardware and for DO NOT STAND UNDER DOOR TO TEST REVERSING excessive slack in the V-Belt and jackshaft chain. The clutch EDGE - USE A CORRUGATED BOX must be tested periodically and adjustments made if necessary OR OTHER SIMILAR OBJECT...

  • Page 18: Wiring Diagram - Single Phase

    WIRING DIAGRAM/SCHEMATIC - SINGLE PHASE 106847 CAUTION: DISCONNECT CONNECT REVERSING POWER BEFORE ATTEMPTING EDGE & TEST MONTHLY. SERVICE OR ADJUSTMENTS. (EPD) - ALLSTAR SERIES T, J, AND H (AU) - ALLSTAR SERIES AUD, AUJ, AND AUH A.O. SMITH BALDOR BALDOR 230V 1P (312 SERIES)

  • Page 19: Wiring Diagram - Three Phase

    CONNECT REVERSING EDGE POWER BEFORE ATTEMPTING AND TEST MONTHLY. SERVICE OR ADJUSTMENTS. (EPD) - ALLSTAR SERIES T, J, AND H 3 PHASE MOTOR WIRING CHART (AU) - ALLSTAR SERIES AUD, AUJ, AND AUH 230 VOLTS, 3 PHASE 460 VOLTS, 3 PHASE...

  • Page 20: Warranty

    Manufacturer’s Limited Warranty Linear LLC warrants its Allstar brand commercial door operators to be free from defect in material and workmanship for a period of two (2) years from the date of purchase. To obtain service contact your dealer. To obtain service under this warranty the buyer must obtain authorization instructions for the return of any goods from Linear before returning the goods.

Table of Contents