Subscribe to Our Youtube Channel
Summary of Contents for FastenMaster PAMFast
- Page 1 FastenMaster and PAMFast are trademarks of OMG Inc. ® ™ PAMFast AutoFeed System ™ Copyright © 2021 OMG Inc. All rights reserved. Owner’s Manual OMG Inc., 153 Bowles Road, Agawam, MA 01001 800·518·3569 FastenMaster.com...
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety ..................1 Precautions ................2 In the Box ................3–4 Getting to Know Your PAMFast Tool ........5–6 Setup and Adjustment ............7–10 Operating Instructions ............11–12 Parts Diagram ..............13–14 Tips/Common Wear Parts/Cleaning ........15–16 Troubleshooting ............... 17-18 Warranty ................19–20 Warning... -
Page 3: Safety
Precautions: • Any screw gun that is supplied with any PAMFast tool is not • Only use genuine PAMFast collated fasteners approved for manufactured or warrantied by FastenMaster. Screw gun the PAMFast AutoFeed tool. -
Page 4: In The Box
• SD-20-DWC13KIT (motor not included) 2. Screw gun manufacturer owner’s manual • SD-20-MAC13KUE • SD-20-MAC13KIT 3. PAMFast AutoFeed tool (fully assembled) • SD-20-DWC13KUE (motor not included) 4. Replacement bits & multi-tool 5. Bit holder for short tool 6. Short Tool Adapter... -
Page 5: Getting To Know Your Pamfast Tool
Getting to Know Your PAMFast Tool Wing Nut 1"– 3" Attachment Extension Pole Screw Gun Countersink Ring Depth Control Holder Gliding Piece Belt Guide Tension Knob/Belt Guide Adapter Extension Pole Handle Cordless Drill Options: Corded Drill Option: WALT Screw gun... -
Page 6: Setup And Adjustment
Fig. 2b of the Depth Control and slide it to the appropriate setting using the numbers Use only genuine PAMFast bits. Every tool comes stamped on the Depth Control (Fig 1a). with one PAMDrive bit installed on tool. Additional bits such When appropriately adjusted, the tip as Phillips and Torx may be purchased. - Page 7 The extension pole can be removed for applications that require a shorter version of the tool. (Fig 5a) • Remove the 1– 3" attachment from the end of the PAMFast tool by loosening the wingnut and pulling the attachment. (5.1) •...
-
Page 8: Operating Instructions
FastenMaster recommends utilizing a continuous drive mode or and load into the 1-3” attachment. (Fig “auto on” mode when using the PAMFast Autofeed tool. 5-6). The fastener strip advances on the • Between drives it is critical that the tool is fully lifted from the down stroke, so the first screw should be surface to allow the nose piece to completely recoil. -
Page 9: Parts Diagram
Parts Diagram Parts Diagram (continued) POS. # PART # DESCRIPTION USED WITH BGS0081 Depth Control 1"- 2" All 12K Series BGS0083 Depth Control 1"- 3" All 13K Series KFS0060 Depth Control Screws (2x) All Screw Guns FXS0008 Gear Wheel Unit All Screw Guns KFS0004 Screw with Roller... -
Page 10: Tips/Common Wear Parts/Cleaning
If the nibs on the • To maintain proper operation of the PAMFast tool, ensure that front of the nose piece or the fastener the gear wheel, inner spring, and gliding piece remain free from Fig. -
Page 11: Troubleshooting
First few screws advance then • Loosen tension control on the belt guide to allow the belt stops moving movement. • Check gear wheel movement as described under Cleaning and Repair. Call 800·518·3569 or access fastenmaster.com for a technical specialist if assistance is needed... -
Page 12: Warranty
Product, free of charge. The remedy under other than stated herein. FastenMaster will not be liable in any this limited warranty is available only for those Products actually event for consequential, punitive, special, incidental, or other exhibiting a manufacturing defect as set forth above.
Need help?
Do you have a question about the PAMFast and is the answer not in the manual?
Questions and answers