1. Manuals
  2. Brands
  3. TransLite Manuals
  4. Network Hardware
  5. TL-9802
  6. Manual

TransLite TL-9802 Manual

Hide thumbs

Advertisement

Table of Contents

P a g e
| 1
PRODUCT MODEL NUMBER:
TL-9802
G.hn COAXIAL ETHERNET BRIDGE
DISCLAIMER
No part of this document may be reproduced in any form without the written permission of the copyright owner.
The contents of this document are subject to revision without notice due to continued progress in methodology,
design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or damage of any kind
resulting from the use of this document.
COPY WARNING
This document includes some confidential information. Its usage is limited to the owners of the product
that it is relevant to. It cannot be copied, modified, or translated in another language without prior written
authorization from TRANSLITE GLOBAL LLC.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TL-9802 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for TransLite TL-9802

  • Page 1 The contents of this document are subject to revision without notice due to continued progress in methodology, design and manufacturing. TRANSLITE GLOBAL LLC shall have no liability for any error or damage of any kind resulting from the use of this document.

  • Page 2: Product Overview

    P a g e PRODUCT OVERVIEW TL-9802 is a coaxial ethernet bridge that uses the G.hn technology and allows you to get data rates up to 2Gbps* over coaxial cable lines and IPTV transmission. It provides an affordable solution by making use of the...
  • Page 3 P a g e G.hn frequency band: 2-200MHz* ➢ PHY rate: up to 2Gbps ➢ Support for home networking connectivity ➢ G.hn LED*1, Ethernet LED*1, PWR LED*1 ➢ RJ-45 GbE Port (Yellow) * 2 ➢ Coaxial 75ohm F-type connector * 2 ➢...

  • Page 4: Specifications

    P a g e SPECIFICATIONS General Information Model No. TL-9802 G.hn over coax Ethernet Bridge G.hn Coaxial Bridge GbE LAN port * 2 Main Function F-type connector* 2 LP + HP diplexer Built-in Product Size 130 x 80 x 25 mm...
  • Page 5 P a g e Input voltage DC 12 V / 1A G.hn Coaxial 200MHz Frequency Band Hi-Pass Filter: 258 ~ 2000MHz G.hn ITU-T G.9960 G.hn ITU-T G.9961 G.hn ITU-T G.9962 PLC protocol G.hn ITU-T G.9963 G.hn ITU-T G.9964 ITU-T G.9972 MAC Access CSMA/CA, TDMA and CSMA Methods...

  • Page 6: Hardware Installation

    P a g e 3. Reset 4. GETH-2 5. GETH-1 6. Power 7. Pair Regulation FCC, ICES report Compliant CE-EMC, CE-LVD Compliant report ROHS Compliant WEEE Compliant Compliant Temperature Operating: -10 ~ 40C Storage: -20 ~ 70C Relative Humidity Operating: 10~85% Non-Condensing Storage: 5~90% Non-Condensing HARDWARE INSTALLATION...
  • Page 7 P a g e Step 1: Plug a Coaxial Bridge into an AC outlet using the AC adapter provided. Use a coaxial cable to connect its F-connector to a wall’s coaxial connector. Then use an Ethernet cable to connect the Bridge to a router or modem.
  • Page 8 P a g e Step 1: Verify the Power LED initial state on both Bridges is solid green. The G.hn Link LED is off when a TL-9802 Coaxial Bridge does not have a secured link to a G.hn network. Step 2: Press and hold the Pairing button on Bridge A for 3 seconds (refer to the image above) until its G.hn Link LED starts blinking amber.
  • Page 9 P a g e APPENDIX BEHAVIOUR Green ON: Power on and ready, can link to other G.hn over Coax Power LED device in unsecured mode. Amber BLINKING: During Security pairing procedure. In this Green procedure, the device joining or being joined into same logical network will continue 120 seconds blinking, until the procedure succeeds or is canceled.
  • Page 10 P a g e | 10 PUSH BUTTON BEHAVIOUR Buttons Security Pairing of two units to establish a network Step 1: Initial state Power LED is solid green. Step 2: Press and hold Pair Button (3 secs) of unit A until Power LED starts blinking in Amber.

Table of Contents