Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Savch SC-3000 Series
- Page 1 SC-3000 Series Control Panel For round knitting machine User Manual User Manual...
- Page 2 520010143000 Vision No. V1.0 Filing time 2017-11-09 SAVCH electric provide a full range of technical support for our customers. All users could contact with the nearest SAVCH office or service center, also could contact with our headquarters directly. SAVCH Electric reserves the copyrights and all rights,...
-
Page 3: Table Of Contents
Contents PREFACE ..................................1 1. Safety instructions ..............................1 1.1 Safety precautions and notes ........................1 1.2 Installation and wiring ...........................1 1.3 Troubleshooting ............................2 1.4 Maintenance ..............................2 2. Product characteristics ............................2 3. Panel functions annotation ............................3 4. The rear cover terminal and wiring diagram......................5 4.1 Functions of the rear cover terminal ......................5 4.2 External wiring ..............................5 5. -
Page 4: Preface
PREFACE Welcome to use SC-3000M microcomputer controller produced by SANCH. For the safety running and effective operation of SC-3000M microcomputer controller, this instruction manual shall be read thoroughly prior to use, which shall also be preserved for later use. 1. Safety instructions For safety running of the machine and prevention of casualties, please read this instruction and always comply with the following safety precautions and notes: 1.1 Safety precautions and notes... -
Page 5: Troubleshooting
1.3 Troubleshooting (1) No display when power on: Power on and check if button OFF red light is flashing, if no flash, please check if the external cable is wrongly connected or locked, or if the voltage is fused; If the OFF light is flashing but can not power on, please check if AC12V(port 5,6) voltage is normal, if the voltage is lower than 11V or below, it will cause unstable power on. -
Page 6: Panel Functions Annotation
(15) Double aerodyne protection to avoid break pin: hardware protection and software protection. (16) The speed of weaving and cleaning is set separately, which makes the operation more flexible. 3. Panel functions annotation Figure 1. Schematic diagram of SC-3000M general control panel functions... - Page 7 Part of annotation for each function of panel: Function Function (23) Setup button Upper broken yarn indicator (24/25) Increase/decrease vaule setting button Middle broken yarn indicator (26) Enter button Probe abnormal indicator (27) Select button Broken cloth indicator (28) Present shift count display button Oil starvation indicator (29) Total display button...
-
Page 8: The Rear Cover Terminal And Wiring Diagram
4. The rear cover terminal and wiring diagram 4.1 Functions of the rear cover terminal SC-3000M controller adopts 555X model 2*1 pin、2*3(2*2) pin、2*7 pin and 2*8 pin socket connector, whose number has the same meaning with the number of terminal circuit board, Those with the same number belong to the same circuit, see figure 2 of appendix. -
Page 9: Example Explanations Of Operation And Display
If any special requirement that is not in above using conditions, please contact us, we will make special setting for u before shipping. 5. Example explanations of operation and display After installing the controller, please make sure all wiring is correct. 5.1 Startup Closing textile power supply, if the red light on the left right of OFF ( ) button in the control panel is on, it... - Page 10 Setting Setting content and Default setting Representing meaning Remarks code adjustable range value Continuous fuel injection ┙0000s of oil pump Intermittently fuel injection 300s running┖0001~9999s by second of oil pump Intermittently fuel injection stop┙0001~9999s by second of oil pump Intermittently fuel injection running┖0001~9999 100 cycle by cycle of oil pump...
-
Page 11: Disable / Enable Of Setting And Speed Regulation Operation
(2) Enter setting 3-8: Under setting 1 or 2, push clear+setup ( ) button, and enter. (3) Setting 3 include three oil working mode parameter setting 3-1, 3-2, 3-3, working mode is selected by pushing button ( ),the Signal “L” display on the left side of the 5 digital nixietub indicates running data, signal “┙” indicates stopping data, unit by S or Loop. -
Page 12: View Production And Browse The Set Values
(3) Operation Machine rotates for one cycle, the decimal of 5 nixietube display from first to end for one time, and count value +1.The count value of both the current shift and the total shifts separately add 1, and the three-bit digital meter displays real-time RPM value. -
Page 13: Application Of Stop, Jog And Force Button
(2) Controller external abnormal situation display. Either one in below 10 external abnormal situations will cause machine stop. (a) Upper broken yarn: The ( ) indicator light blinks, red light of external 3-color lamp and corresponding yarn feeding light blink (super force state inhibits all yarn feeding light from blink). (b) Middle broken yarn: The ( ) indicator light blinks, yellow light of external 3-color lamp and corresponding yarn feeding light blink (super force state inhibits all yarn feeder light from blink). -
Page 14: Shutdown
(2) JOG: Pressing the ( ) button when stopping the machine, the machine will slowly run or stop. Implement JOG operation under normal running state, the machine will turn into micro running, and stop after releasing the button. If press ( ) and ( ) buttons at the same time, the machine will turn into micro running, then release ) button, and the machine automatically turns into running in jog speed. - Page 15 Diagram 2. SC-3000M Rear cover wiring diagram...
- Page 16 Diagram 3. SC-3000M Controller external wiring diagram...
- Page 17 ■ Innovate for more | win forever ■ Industry intelligence | Energy saving | Green power Savch wechat Service Number Quanzhou Factory Sales service contact address Address:3# Zixin Road, Jiangnan Hi-Tech Industrial Park, Quanzhou, Fujian, China Tel：0595-24678267 Fax：0595-24678203 Service Network Website：www.savch.net...