Do you have a question about the G-FTL Series and is the answer not in the manual?
Questions and answers
Summary of Contents for FTS G-FTL Series
Page 1
Owner Manual Model number: G-FTL085/G-FTL105/G-FTL125/G-FTL155 Serial number: Rotovator Date of purchase: G-FTL Series Factory reference: FTL85/FTL105/FTL125/FTL155 This manual should be considered a permanent part of this attachment and therefore should remain with it even if the attachment is subsequently sold.
Page 2
Safety Information Safety Information (continued) Before installation/maintenance, ensure tractor and attachment are Attachment Pre-use Checks stationary with the hydraulic lift system in a neutral position, and the ignition key removed. Read and understand this manual fully Upon receipt of your new attachment and again within the first 4 hours of before operating machinery.
Contents Specifications The Rotovator G-FTL model is ideal for maintaining allotments and Safety Information………………………………………………………………………..page 3-4 vegetable gardens. The blades cultivate and break up soil to aid planting. Specifications…………………………………………………………………………………..page 6 The G-FTL height is controlled by adjustable skids to 9cm. The blades are Installation Overview…………………………………………………………………….page 7-8 driven by a chain.
Installation Overview Installation Overview (Continued) Before installation/maintenance, the tractor and attachment should • Check the tractor's 3-point hydraulic lift system. It should operate up be stationary with the hydraulic lift system in a neutral position and and down smoothly and hold its position when set. the ignition key removed.
Set Working Depth Gearbox Maintenance Before installation/maintenance, the tractor and attachment should Before installation/maintenance, the tractor and attachment should be stationary with the ignition key removed. Follow labels on any oil be stationary with the hydraulic lift system in a neutral position and and grease, always dispose of oils as instructed.
Servicing & Maintenance Chain Case Oil Before installation/maintenance, the tractor and attachment should Before installation/maintenance, the tractor and attachment should be stationary with the ignition key removed. Follow labels on any oil be stationary with the ignition key removed. Follow labels on any oil and grease, always dispose of oils as instructed.
Parts Diagram 1 Attaching & Resizing PTO Shaft Before installation/maintenance, the tractor and attachment should be stationary with the ignition key removed. Ensure all safety guards are in place and cover the PTO shaft when extended, ensure the sprung locking collar slides freely and is securely in the groove on the PTO.
Parts List for Diagram 1 Parts List for Diagram 1 (Continued) Diag. Diag. Ref No Part No Part Description Ref No Part No Part Description 703400011 MZ105.127 Top Drive chain wheel 803400077 FTL.125.018 Shaft protection pipe (R) 506060315 GB894.1-32 Circlip 32 803440016 EF100.00.019 Suspense pin...
Page 9
Parts List for Diagram 1 (Continued) Parts List for Diagram 1 (continued) Diag. Diag. Ref No Part No Part Description Ref No Part No Part Description 703400182 FTL.125.136 Bolt 803400047 FTL.125.016 Support stand 703400198 FTL.125.139 Gasket 707180017 RB-00.101 The brance pin 703400031 FTL.125.013 Transmission chains 16Ax17...
Parts Diagram 2 & Parts List Diag. Ref No Part No Part Description Bearing seat for input 703400003 FTL.125.102 shaft Paper washer for rear 703400005 FTL.125.106 cover 506060317 GB894.1-35 Circlip 35 510020398 CFW-35X72X10 Oil seal 35x72x10 511022613 GB276-6207 Bearing 6207 511016411 GB297-30207 Bearing 30207...
Need help?
Do you have a question about the G-FTL Series and is the answer not in the manual?
Questions and answers