Do you have a question about the CQ-C8403W and is the answer not in the manual?
Questions and answers
Summary of Contents for Matsushita Electric CQ-C8403W
Page 1
ORDER NO. ACED051233C3 AUTOMOTIVE AFTERMARKET CQ-C8403W WMA MP3 CD Player/Receiver SPECIFICATIONS Specifications* General Power Supply DC 12V (11V - 16V), Test Voltage 14.4V Negative Ground Tone Controls (Bass/ Bass: ±12dB at 60Hz / Treble: ± Treble) 12dB at 16kHz Equalizer Center Frequency 60, 160, 400, 1k, 3k, 6k, 16k (Hz)
** Dimensions and Weight shown are approximate. ** Above specifications comply with EIA standards. 2005 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law. 1. ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF stamp on the PCB.
iron with temperature control and adjust it to 700 ± 20°F (370 ± 10°C). In case of using high temperature soldering iron, please be careful not to heat too long. - Pb free solder will tend to splash when heated too high (about 1100°F/ 600°C) - This lead free solder will be used for the products after serial No.
9.2. How to Install the Main P.C.B. of the Electric Display 10. TERMINALS DESCRIPTION 10.1. Main Block IC601 : C2CBKG000034...
Page 7
Port Description Port Description FM AM CD FM AM CD 27 CH STB Strobe from 1 PANEL Panel open 0 5.2 5.2 Changer OPEN detection 28 CH REM Remote control O 4.9 4.9 0.4 2 PANEL Panel close 0 5.2 codes to Changer CLOSE detection...
Page 8
Port Description FM AM CD 51 DCDC Not connected CONT 52 FP Open/Close of O 4.9 5.0 4.9 MOTOR1 Front panel 1 53 FP Open/Close of O 4.9 5.0 4.9 MOTOR2 Front panel 2 54 V CONT1 Reference voltage 0 5.0 control for motor driver 55 REMO 1...
10.2. Display Block IC901 : C2CBKJ000195 Port Part Name & I/O (V) Description 1 NC Not connected 2 DCLK SLV4 Slave D-CLK4 (Clock for image data) 3 UART SS4 4 UART SS3 5 D DIS Disable for Anode drive (Disable for image signal) 6 PADJ IO2 Anode output pulse...
Page 10
Port Part Name & I/O (V) Description 28 X SYNC Clock for Cathode scan; or Latch strobe for Anode output pulse width adjusting data and Anode output current adjusting data 29 A CLK TA Anode output pulse width adjusting clock 30 NC Not connected 31 NC...
Page 11
Port Part Name & I/O (V) Description 56 NC Not connected 57 GND 58 NC Not connected 59 VCC3.3V Power supply 60 NC Not connected 61 NC Not connected 62 NC Not connected 63 FLASH OE Output enable for Flash memory 64 NC Not connected 65 FLASH WE...
Page 12
Port Part Name & I/O (V) Description 99 FLASH A2 A2 in Address bus 100 FLASH A1 A1 in Address bus 101 FLASH A0 Not connected 102 FLASH D15 DQ15 in Data bus I/O 3.1 103 FLASH D14 DQ14 in Data bus I/O 0.6 104 FLASH D13 DQ13 in Data bus...
Port Part Name & I/O (V) Description 138 NC Not connected 139 NC Not connected 140 AD AVSS 141 TH DETECT Thermal detection 142 AD VREF +5V Power supply 143 AD AVCC +5V Power supply 144 PADJ IO3 Anode output pulse width adjusting data 3 (Image data) 10.3.
Port Descriptions I/O (V) DSP IC CCE BUCK DSP IC CK BUS3 DSP IC BUS3 BUS2 DSP IC BUS2 BUS1 DSP IC BUS1 BUS0 DSP IC BUS0 RESET Mechanics deck REST SW input Mechanics deck SW1 input Mechanics deck SW2 input CONT DSP IC power control 1...
11.2. CD Servo Block IC401,403 : YESAM341 IC402 : YESAM342 12. REPLACEMENT PARTS LIST Notes : 1. Be sure to make your orders of replacement parts according to this list. 2. Important safety notice: Components, identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts.
Page 19
After the discontinuation of assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependent on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.
14. CD PLAYER PARTS LIST Notes : 1. Be sure to make your orders of replacement parts according to this list. 2. Important safety notice: Components, identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturer's specified parts.
Page 38
3. Location keys in the remarks column indicates the general location of the parts shown in the exploded drawing, as in a road map. 4. The marking (RTL) indicates that Retention Time is limited for this item. After the discontinuation of assembly in production, the item will continue to be available for a specific period of time.
Page 39
Ref. No. Part No. Part Name & Description Remarks C214 YESCC435 Ceramic, 47pF 50WV C215 YESCC444 Ceramic, 0.015 F 50WV C216 YESCC442 Ceramic, 0.01 F 50WV C218 YESCC442 Ceramic, 0.01 F 50WV C219 YESCC525 Ceramic, 0.047 F 50WV C220 YESCC439 Ceramic, 0.1 F 25WV C221...
Page 40
Ref. No. Part No. Part Name & Description Remarks Ref. No. Part No. Part Name & Description Remarks C407 YESCC452 R206 ERJ3GEY0R00V Chip, 0 1/16W Ceramic, 1 F 16WV R207 YESRG224 C408 YESCC453 Chip, 100k 1/10W Ceramic, 0.47 F 25WV R208 YESRG224 Chip, 100k...
Page 41
Ref. No. Part No. Part Name & Description Remarks R314 YESRG356 Chip, 15k 1/10W R324 YESRG223 Chip, 10k 1/10W R325 YESRG223 Chip, 10k 1/10W R326 ERJ3GEY0R00V Chip, 0 1/16W CONNECTORs CN101 YESAE409 Connector, 18P Ref. No. Part No. Part Name & Description Remarks CN102 YESAE350...
Need help?
Do you have a question about the CQ-C8403W and is the answer not in the manual?
Questions and answers