Summary of Contents for WORKSWELL BB200 SDK
- Page 1 WORKSWELL BB200 SDK USER MANUAL FW Version: 1.4.20 or higher Release date: 7 June, 2021 Revision : 1.6.2 EN...
-
Page 2: Table Of Contents
Command protocol ........5. BB200 SDK Control GUI Applica on 5.1 Setup . -
Page 3: Legal Disclaimer
Workswell s.r.o. will, at its op on, repair or replace any such defec ve product free of charge if, upon inspec on, it proves to be defec ve in material or workmanship and provided that it is returned to Workswell within the said twelve-month period. -
Page 4: Warning And Cau Ons
Warning and Cau ons 2.1 Warnings Before using the Workswell BB200, please read the whole User Manual. Before powering up the product, please check that there is no visible damage or malfunc on; the cables are connected properly and also verify that the polarity of the cables is correct. -
Page 5: Help And Faq
Most of the solu ons needed for any of the technical difficul es that you may encounter can be found within this manual. In case you have further ques ons either: Contact your authorized dealer; Contact our technical support at support.workswell.eu Headquarters Revision 1.6.2 EN, 7... -
Page 6: General Device Informa On
Revision 1.6.2 EN, 7 Jun, 2021 E-mail and Web Mobile: U Albrechtova vrchu 12 All pictures are only for illustra on. info@workswell.eu +420 725 877 063 Reg. No.: 29048575 155 00, Prague 13 Real values may vary. www.workswell.eu VAT No.: CZ29048575... -
Page 7: Usb Communica On
4.1.2 USB Communica on A USB-C cable can be used to set the parameters of the Workswell BB200 on versions 1.4.17 and above. Connect the device to the computer with a USB-C cable. The device must be connected to the power supply at all mes, connec ng only to the USB-C without supplying power to the device will not suffice and you will not be able to... -
Page 8: Bb200 Sdk Control Gui Applica On
BB200 SDK Control GUI Applica on This chapter contains informa on about the Workswell BB200 SDK Control GUI applica on, which was developed to demonstrate the possible usage of this SDK. This applica on enables full control of the black body from a desktop computer and allows the user to update the firmware on the device. -
Page 9: Connect Bu On
5.2.1 Connect bu on The connect bu on is used to connect the Workswell BB200 to your control applica on. You cannot control more than one BB200 device at the same me. A er clicking the connect bu on the port selec on window appears. -
Page 10: Ac Va On Window
SDK will be ac vated permanently. Figure 5.3 – Ac va on window 5.2.2 Upload Firmware bu on This func on is working only on Windows! If you wish to update your firmware contact our support at support@workswell.eu. Headquarters Revision 1.6.2 EN, 7 Jun, 2021... -
Page 11: Bb200 Informa On
5. BB200 SDK CONTROL GUI APPLICATION 5.2.3 BB200 informa on Figure 5.4 – Informa on This panel shows basic info about the product. Headquarters Revision 1.6.2 EN, 7 Jun, 2021 E-mail and Web Mobile: U Albrechtova vrchu 12 All pictures are only for illustra on. -
Page 12: Control Panel
5. BB200 SDK CONTROL GUI APPLICATION 5.2.4 Control panel The setpoint temperature can be changed here. Figure 5.5 – Control panel 5.2.5 Temperature unit switch The temperature units can be switched between Celsius and Fahrenheit using a switch. 5.2.6 Lock The BB200 can be locked or unlocked using a switch. -
Page 13: Log
5. BB200 SDK CONTROL GUI APPLICATION 5.2.8 Log The log switch shows or hides text field with logs of current communica on with the BB200. Last 10 commands and answers are shown in a log. Headquarters Revision 1.6.2 EN, 7... - Page 14 Contacts Sales Department Headquarters Partners Worldwide Mobile: +420 725 955 464 Workswell s.r.o. Visit our partner list online E-mail: sales@workswell.eu U Albrechtova vrchu 12 155 00, Prague 13 Czech Republic Company contact details Mobile: +420 725 877 063 E-mail: info@workswell.eu...
Need help?
Do you have a question about the BB200 SDK and is the answer not in the manual?
Questions and answers