User Manual for Tersus RS460H Radio v1.1 Table of Content Table of Content........................1 List of Figures........................... 2 List of Tables..........................2 Revision History........................3 1. Introduction........................... 4 1.1 Overview......................... 4 1.2 Specification........................5 1.3 Accessories........................8 2. General Operation......................10 2.1 Basic Operation......................10 2.2 Software Configuration....................13...
User Manual for Tersus RS460H Radio v1.1 List of Figures Figure 1.1 2W Radio RS460H................ 4 Figure 1.2 Serial Interface RS232..............6 Figure 1.3 410-470MHz radio whip antenna ..........8 Figure 1.4 Serial-5pin to DC JACK and DB9 male cable......9 Figure 1.5 DC JACK male with two wires.............9...
User Manual for Tersus RS460H Radio v1.1 Revision History Version Revision Date Change summary 20210720 Initial Release 20210903 Renew the figures 20220105 Upgrade the Figure1.1& Table 2 & Section 1.3...
This chapter mainly introduces the overview and specification of the Tersus 2W Radio RS460H. Overview The Tersus 2W radio RS460H is a radio solution for both the base and the rover. It provides reliable data communications for mission-critical applications where a combination of stability, superior performance and long distance are required.
User Manual for Tersus RS460H Radio v1.1 Specification Table 1 Specifications of 2W Radio RS460H Voltage and Power Input voltage DC 5 ~ 12V 6W (DC 5V, transmitting power 2W) Power consumption in transmitting 5W (DC 5V, transmitting power 1W) Power consumption in receiving 0.5W (DC 5V)
User Manual for Tersus RS460H Radio v1.1 Mechanical Dimension 107 * 62 * 26.6mm Weight ≈200g The serial interface provides power and data communication function for radio equipment.Interface Type: RS232. Figure 1.2 Serial Interface RS232 Table 2 Pin definition Pin No.
User Manual for Tersus RS460H Radio v1.1 Table 3 Default factory configuration of RS460H Channel Frequency 457.550MHz 458.050MHz 458.550MHz 459.050MHz 459.550MHz 460.550MHz 461.550MHz 462.550MHz 463.550MHz 464.550MHz Customized frequency 410~470MHz Table 4 Detailed configuration information Protocol Modulation type Channel band Air baud rate(bps) GMSK 12.5 kHz...
User Manual for Tersus RS460H Radio v1.1 Accessories The accessories of 2W Radio RS460H are listed below. The 410-470MHz radio whip antenna is to be installed on 2W radio RS460H to transmit and receive radio signal. This antenna is elastic whip structure, resistant to bending.
User Manual for Tersus RS460H Radio v1.1 Figure 1.4 Serial-5pin to DC JACK and DB9 male cable Figure 1.5 DC JACK male with two wires Figure 1.6 DB9 Female to USB Type A Male converter cable Note: The Serial-5pin to DC JACK and DB9 male cable, DC JACK male...
User Manual for Tersus RS460H Radio v1.1 2. General Operation Install the radio antenna before switching the radio transceiver to transmit mode, or the radio transceiver will be damaged. Basic Operation Figure 2.1 Front Panel of the Radio Table 5 Definition for each button Serial No.
Page 12
User Manual for Tersus RS460H Radio v1.1 The basic operations include: 1) Boot up The radio module boots up directly when powered on. 2) Channel switching Press the channel switching button once, the channel is increased by one. The LED displays the current channel value, the channel display is 0 to 9, and the default is 0.
User Manual for Tersus RS460H Radio v1.1 for transmit mode, and red light is flashing for transmitting data. R is steady green for receive mode, and green light is flashing for receiving data. The default is the receive mode. 6) Restore default configuration Simultaneously press and hold the power switching button and protocol switching button for 1 second to recover to the default configuration.
User Manual for Tersus RS460H Radio v1.1 Software Configuration The detailed steps of software configuration are as follows: 1) Hardware connection Use the accessary cables listed in section 1.3 to connect the radio to the computer following the connection in the figure below. Power on the radio using 5V or 12V external power supply.
User Manual for Tersus RS460H Radio v1.1 2) Radio Config Tool Open the radio configuration software ‘TersusRadio’ obtained from Tersus support. Ensure the port is selected correctly, then click [Connect]. Figure 2.3 TersusRadio Config Tool 3) Read After the connection is successful, click the [Read] button to read all current...
User Manual for Tersus RS460H Radio v1.1 Installation Tips 2.3.1 Radio installation As a transmission, the radio is hooked on a tripod. As a rover station, the radio is installed in the rover station bracket. (1) Large amount of heat would be generated when the radio is in transmission.
Proprietary Notice All Information in this document is subject to change without notice and does not reflect the commitment on Tersus GNSS Inc. No part of this manual may be reproduced or transmitted by all means without authorization of Tersus GNSS Inc.
Need help?
Do you have a question about the RS460H and is the answer not in the manual?
Questions and answers