Intended Use; Drill Driver Safety Warnings; Residual Risks - Ryobi R18DD2 Original Instructions Manual

Safety, performance, and dependability have been given
top priority in the design of your drill driver.

INTENDED USE

The drill driver is intended to be used only by adults who
have read and understood the instructions and warnings
in this manual, and can be considered responsible for their
actions.
The product can be used for drilling into various materials,
including wood, metal, and plastics using a drill bit having a
shank diameter of less than 10 mm.
The product can be used to drive and remove screws and
bolts using an appropriate bit.
Do not use the product in any way other than those stated
for intended use.
WARNING
Read all safety warnings, instructions, illustrations
and specifications provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instruction for future reference.

DRILL DRIVER SAFETY WARNINGS

■
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
■
Hold power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring. Cutting
accessory contacting a "live" wire may make exposed
metal parts of the power tool "live" and could give the
operator an electric shock.
■
Hold power tool by insulated gripping surfaces,
when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a
"live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
■
Wear ear protectors when drilling. Exposure to noise
can cause hearing loss.
■
When not in use, all tools should be disconnected from
power source.
■
The dust produced when using the product may pose a
health hazard. Do not inhale the dust. Wear a suitable
dust protection mask..
■
Do not operate on materials (e.g., asbestos) that
present a health hazard.
■
Switch off the product immediately if the bit stalls. Do
not switch on the product again while the bit is stalled,
as doing so could trigger a sudden recoil with a high
reactive force. Determine why the bit stalled and rectify
this, paying heed to the safety instructions.
The possible causes may be:
– it is tilted in the workpiece
– it has pierced the workpiece
– the product is overloaded
■
Sawdust and splinters must not be removed while the
product is running.
■
When working in walls, ceilings, or floors, avoid hitting
electrical cables and gas or water pipes.
■
Secure your workpiece with a clamping device.
■
Ambient temperature range for tool during operation is
between 0 ˚C and 40˚ C.
■
Ambient temperature range for tool storage is between
0 ˚C and 40˚ C.
■
The recommended ambient temperature range for the
charging system during charging is between 10 ˚C and
38˚ C.
ADDITIONAL BATTERY SAFETY WARNINGS
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
■
Ambient temperature range for battery during use is
between 0 ˚C and 40˚ C.
■
Ambient temperature range for battery storage is
between 0 ˚C and 20˚ C.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.

RESIDUAL RISKS

Even when the product is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise, and the operator
should pay special attention to avoid the following:
■
Risk of electrocution if electric cables are drilled into.
Always grasp the product by designated handles; do
Autogoods "130"
WARNING
English |
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
1