Related Manuals for NexAIoT NISE 70 Series
Summary of Contents for NexAIoT NISE 70 Series
- Page 1 NexAIoT Co., Ltd. IoT Automation Solutions Business Group Fan-less Computer NISE 70 User Manual NexAIoT Co., Ltd. www.nexaiot.com Published December 2021...
-
Page 2: Table Of Contents
Fan Connector ................15 Front Panel ..................4 Debug Connector ................16 Rear Panel ...................4 Mini-PCIe Connector ..............16 Mechanical Dimensions ................5 M.2 B Key Slot ................17 Nano SIM Slot ................17 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 3 Chapter 4: BIOS Setup About BIOS Setup .................30 When to Configure the BIOS ..............30 Default Configuration ................31 Entering Setup ..................31 Legends ....................31 BIOS Setup Utility ..................33 Main ....................33 Advanced ..................34 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 4: Preface
No describes how to keep the system CE compliant. part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written consent from NexAIoT Declaration of Conformity Co., Ltd. -
Page 5: Rohs Compliance
(Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) < 0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm. In order to meet the RoHS compliant directives, NexAIoT has established an engineering and manufacturing task force to implement the introduction of green products. -
Page 6: Warranty And Rma
“NexAIoT RMA Service Form” for the RMA number apply process. ▪ If RMA goods can not be repaired, NexAIoT will return it to the customer without any charge. ▪ Customers can send back the faulty products with or without accessories (manuals, cable, etc.) and any components from the card, such as CPU... -
Page 7: Installation Recommendations
Using your fingers can disconnect most of the connections. It is recommended that you do not use needle-nose pliers to disconnect connections as these can damage the soft metal or plastic parts of the connectors. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 8: Safety Information
Discard used batteries according to the manufacturer’s instructions. ▪ This product is intended to be supplied by an approved power adapter, rated 12Vdc, 5A or 24Vdc, 2.5A minimum and Tma 55 degree Celsius. If further assistance is needed, please contact NexAIoT for further information. viii Copyright ©... -
Page 9: Safety Precautions
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 10: Technical Support And Assistance
Preface Technical Support and Assistance Conventions Used in this Manual 1. For the most updated information of NexAIoT products, visit NexAIoT’s Warning: website at www.nexaiot.com. Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself 2. -
Page 11: Global Service Contact Information
Fax: +886-2-8226-7782 Shanghai, 201108, China Taichung City, 406, Taiwan, R.O.C. Email: sales@nexcom.com.tw Tel: +86-21-5278-5868 Tel: +886-4-2249-1179 www.nexcom.com.tw Fax: +86-21-3251-6358 Fax: +886-4-2249-1172 Email: sales@nexaiot.com Email: sales@nexcom.cn www.nexaiot.com www.nexcom.cn Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 12 9F, Tamachi Hara Bldg., Chongqing City, 402160, China 4-11-5, Shiba Minato-ku, Tel: +86-23-4960-9080 Tokyo, 108-0014, Japan Fax: +86-23-4966-5855 Tel: +81-3-5419-7830 Email: sales@nexgol.com.cn Fax: +81-3-5419-7832 www.nexcobot.com/NexGOL Email: sales@nexcom-jp.com www.nexcom-jp.com Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 13: Package Contents
Round Head Screw Long Fei:P2x3 ISO+NYLON P2x3 NI NYLOK 50311F0215X00 (H)I Head Screw Long Fei:I3x5ISO+NYLOK NIGP I3x5 NI NYLOK 5060200549X00 Thermal Pad For VTC6220-BK VPU-02 Card Heatsink E-LIN 40x30x5mm K=2.5 W/mk PK404HC xiii Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 14: Ordering Information
Core™ i5-1145G7E Tiger Lake-UP3 processor fanless system NISE 70-T03 (P/N: 10J00007002X0) ▪ Intel Core™ i7-1185G7E Tiger Lake-UP3 processor fanless system ® ▪ 24V, 60W AC /DC power adapter w/o power cord (P/N: 7400060054X00) Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 15: Chapter 1: Product Introduction
▪ 1 x mini-PCIe sockets support optional mSATA/Wi-Fi/BT/4G LTE module ▪ Support operating temperature from -5 to 55 Celsius degree ▪ Support +12V to 24VDC input; support ATX power mode Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 16: Hardware Specifications
▪ 2 x Antenna hole Environment ▪ 1 x 2-pin remote power on/off switch ▪ Operating temperature: ▪ Support +12V to 24V DC input Ambient with air flow: -5°C to 55°C Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 17 ▪ Vibration protection with mSATA & M.2 condition: – Random: 2Grms @ 5~500 Hz, IEC60068-2-64 – 64-Sinusoidal: 2Grms @ 5~500 Hz, IEC60068-2-6 Certifications ▪ CE ▪ FCC Class A Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 18: Knowing Your Nise 70
USB 2.0 ports to connect the system with USB 2.0/1.1 devices. Remote On/Off Switch Used to connect a remote to power on/off the system. Remote COM1 COM2 On/Off DC Input USB 2.0/3.0 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 19: Mechanical Dimensions
Chapter 1: Product Introduction Mechanical Dimensions 187.40 198.80 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 20: Chapter 2: Jumpers And Connectors
Static electricity can damage many of the electronic ▪ Use correct screws and do not over tighten screws. components. Humid environments tend to have less static electricity than Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 21: Jumper Settings
Refer to the illustrations below for examples of what the 2-pin and 3-pin jumpers look like when they are short (on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right) Three-Pin Jumpers: Pins 1 and 2 are Short Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 22: Locations Of The Jumpers And Connectors For Nisb 70
NISE 70. It shows the locations of the jumpers and connectors. DC_VIN1 REM_BT1 COM2 COM1 USB2 USB1 W_BAT1 GPIO1 FAN1 SIM1 ESPI_DB1 16 18 DIMM2 JPWR_MODE1 NGFF1 PWR_BT1 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 23: Dip Switches
ATX/AT Mode Selection Connector type: 2-pin DIP switch Connector location: JPWR_MODE1 Connector location: SW1 Definition Definition Clear CMOS ATX Mode Reset CSME AT Mode Default: 1-OFF, 2-OFF Default: 1-2 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 24: Clear Cmos Switch
Chapter 2: Jumpers and Connectors Clear CMOS Switch Connector location: PWR_BT1 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 25: Connector Pin Definitions
Connector location: COM1, COM2 COM1 COM2 Definition Definition Definition DCD#_COM1 DCD#_COM2 RXD_COM1 RXD_COM2 GND_EARTH TXD_COM1 TXD_COM2 DTR#_COM1 DTR#_COM2 DSR#_COM1 DSR#_COM2 RTS#_COM1 RTS#_COM2 CTS#_COM1 CTS#_COM2 RI#_COM1 RI#_COM2 (COM1:RS-232/422/485, COM2: RS232 only) Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 26: Usb 3.0 Ports
USB 3.0 Ports Power Button Connector Connector type: Dual USB 3.0 Type A ports Connector type: 1x2 2-pin header Connector location: USB1, USB2 Connector location: REM_BT1 Definition REM_BT# Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 27: Display Connector
Connector location: LAN1 Status Flashing Yellow Data activity No activity LINK Link Status Steady Green 1G network link Steady Orange 100Mbps network link 10Mbps or no link Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 28: Lan 2 Port
Connector location: LAN2 Status Flashing Yellow Data activity LINK No activity Link Status Steady Green 1G network link Steady Orange 100Mbps network link 10Mbps or no link Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 29: Internal Connectors
Connector type: 2x5 10-pin header Connector type: 1x6 6-pin header Connector location: GPIO1 Connector location: FAN1 Definition Definition Definition Definition TACH_FAN1 PWM_FAN1 GPO_0 GPI_0 GPO_1 GPI_1 +5VSB GPO_2 GPI_2 GPO_3 GPI_3 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 30: Debug Connector
Chapter 2: Jumpers and Connectors Debug Connector Mini-PCIe Connector Connector type: 1x10 10-pin header Connector location: MPCIE1 Connector location: ESPI_DB1 Definition Definition PLTRST# eSPI_CLK eSPI_CS# eSPI_IO3 eSPI_IO2 eSPI_IO1 eSPI_IO0 eSPI_RESET# +3VSB Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 31: B Key Slot
Chapter 2: Jumpers and Connectors M.2 B Key Slot Nano SIM Slot Connector location: NGFF1 Connector location: SIM1 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 32: System Internal Function Connector
Chapter 2: Jumpers and Connectors System Internal Function Connector Connector type: 2x5 10-pin header Connector location: CN1 Definition Definition +5VSB USB2_N USB2_P UART_RX UART_TX I2C_SCL I2C_SDA GPO_3 +5VSB Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 33: Block Diagram
TYPE A x 2 USB2.0 P1~7 12C P0 SLB9670VQ2.0 eSPI 80 Port eSPI SUPER I/O H/W Monitor 12C P0 UART P3 NCT6126D 2.0 Pin Header XR34350 COM1/COM2 GPIO Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 34: Chapter 3: System Setup
2. With the screws removed, lift up the cover and remove it from the chassis. screws each on the top and on the sides. Screws on the sides Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 35: Installing A So-Dimm Memory Module
The ejector tabs at the ends of the socket will automatically snap into the locked position to hold the module in place. Memory Module SO-DIMM Socket Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 36: Installing A 5G/4G Lte/Msata Module (Full-Size)
2. Insert the module into the mini-PCIe slot at a 45-degree angle until the gold-plated connector on the edge of the module completely disappears into the slot. Mini-PCIe Socket Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 37 Chapter 3: System Setup 3. Push the module down and secure it with a screw. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 38: Installing A Wlan/Bluetooth Mini-Pcie Module (Half-Size)
45-degree angle until the gold-plated connector on the edge of the module completely disappears inside the slot. Push the module down and then secure it with mounting screws. WLAN Module Module Bracket Mounting Screw Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 39: Installing A Sim Card
2. Release the cover and place the SIM card onto the holder. Push through to insert the SIM card into the SIM card slot. SIM Card SIM card slot Note: SIM-card cover is secured to the board. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 40 Chapter 3: System Setup 3. Close the cover and secure it to the original position. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 41: Installing An Antenna
Note: Please remove the gaskets (ring 1 and ring 2) on the SMA 1. Remove the antenna hole cover located on the front and rear panel. antenna jack first. Ring 2 Ring 1 Ring 2 Ring 1 Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 42 2. Insert the SMA antenna jack end of the cable through the antenna hole, Note: Gasket and washer installation sequence. and insert the 2 rings (ring 1 and ring 2) and two washers back to the antenna jack. Installation Sequence Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 43 RF Cable Side A facing inwards and each other Side A Side B 4. Connect the external antenna to the antenna jack. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 44: Chapter 4: Bios Setup
It is important, therefore, first to try to understand all the setup options, and if the BIOS is updated in the future. second, to make settings appropriate for the way you use the computer. To check for the latest updates and revisions, visit the NexAIoT website at When to Configure the BIOS www.nexaiot.com. -
Page 45: Default Configuration
Powering on the computer and immediately pressing allows you to enter Setup. Load optimized default values. Saves and exits the Setup program. Press <Enter> to enter the highlighted sub-menu. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 46 When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 47: Bios Setup Utility
F3: Optimized Defaults F4: Save & Exit IGFX VBIOS Version ESC: Exit IGFX GOP Version 17.0.1070 Total Memory 8192 MB ▼ Version 2.21.1278. Copyright (C) 2021 AMI Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 48: Advanced
F3: Optimized Defaults F4: Save & Exit ESC: Exit Active Processor Core Select the number of cores to enable in each processor package. Version 2.21.1278. Copyright (C) 2021 AMI Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 49 Allows more than two frequency ranges to be supported. C states Enable/Disable CPU Power Management. Allows CPU to go to C states when it's not 100% utilized. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 50 Security Device. TCG EFI protocol and INT1A interface will not be available. SHA-1 PCR Bank Enables or disables SHA-1 PCR Bank. SHA256 PCR Bank Enables or disables SHA256 PCR Bank. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 51 Configuration settings for serial port 1 to port 2. Select this to change the serial port mode to RS232, RS422, RS485. Terminal resistor Enable or disable terminal resistor. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 52 System temperature Detects and displays the current system temperature. CPU temperature Detects and displays the current CPU temperature. +3.3V to VCORE Detects and displays the output voltages. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 53 Disabled: Disable option will keep USB devices available only for EFI applications. XHCI Hand-off This is a workaround for OSs that does not support XHCI hand-off. The XHCI ownership change should be claimed by the XHCI driver. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 54 Enables or disables UEFI network stack. This field is used to enable or disable CSM support, if Auto option is selected, based on OS, CSM will be enabled or disabled automatically. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
- Page 55 F3: Optimized Defaults F4: Save & Exit F4: Save & Exit ESC: Exit ESC: Exit Version 2.21.1278. Copyright (C) 2021 AMI Version 2.21.1278. Copyright (C) 2021 AMI Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
-
Page 56: Chipset
Version 2.21.1278. Copyright (C) 2021 AMI VT-d Enables or disables VT-d function on MCH. System Agent Configuration Enters the System Agent submenu. PCH-IO Configuration Enters the PCH-IO Configuration submenu. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 57: Security
User Password DVMT Total Gfx Mem Select this to reconfigure the user’s password. Select DVMT5.0 total graphic memory size used by the internal graphics device. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 58: Boot
When set to Off, the function of the numeric keypad is the arrow keys. Quiet Boot Enabled Displays OEM logo instead of the POST messages. Disabled Displays normal POST messages. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 59: Save & Exit
To save the changes and reset, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes. You can also press <F4> to save and exit Setup. Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 60: Appendix A: Gpi/O Programming Guide
GPI/O (General Purpose Input/Output) pins are provided for custom system design. This appendix provides definitions and its default setting for the ten GPI/O pins in the NISE 70 series. The pin definition is shown in the following table: GPIO PowerOn... -
Page 61: Appendix B: Watchdog Timer Setting
WDT_SET); outportb(SUPERIO_PORT+1, 0x00); # Use the second # Use the minute, change value to 0x08 # Set WDT sec/min outportb(SUPERIO_PORT, WDT_VALUE); outportb(SUPERIO_PORT+1, 0x05); #Set 5 seconds Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... -
Page 62: Appendix C: Power Consumption
5V, 0.5A (Cement Resistor) for full load USB 3.0*3 5V, 1.0A (Cement Resistor) for full load COM (All ports) RS232 Loopback (115200 baud rate) Display Interface HDMI Interface LCD Monitor Keyboard & Mouse Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual... - Page 63 100% Full Loading Mode Power Consumption 12 V 3.42 A 41.04 W 24 V 1.72 A 41.28 W Note: CPU power limit value is 15W by default (by BIOS setting). Copyright © 2021 NexAIoT Co., Ltd. All Rights Reserved. NISE 70 User Manual...
Need help?
Do you have a question about the NISE 70 Series and is the answer not in the manual?
Questions and answers