Tresco FREEDiM L-RGBCCT-RMT Instructions

System Parts:

(1) Dynamic RF LED Remote Control . . . . . . . . . . . . . . . P/N: L-RGBCCT-RMT
(1) Dynamic RF LED Parent Controller . . . . . . . . . . . . . . P/N: L-RGBCCT1-PREC
(1) Dynamic RF LED Child Receiver (optional) . . . . . . . . P/N: L-RGBCCT1-CREC
(1) Power Supply, Class 2, 12VDC 60W max (or) 24VDC 96W max
Tresco low voltage 12VDC or 24VDC LED RGB or CCT light(s) with Starter Cord
®
The FREEDiM Remote Control starts out with preset settings:
• RGB preset - all values start at 0-0-0
• CCT preset - begins at 2700K
RGB CCT Remote Control

Remote Control Specifications:

L-RGBCCT-RMT
Operating Voltage: . . . . . . . . . . . . . . . . (2) AAA batteries
Radio Frequency: . . . . . . . . . . . . . 916 .5 MHz
RF Remote Distance: . . . . . . . . . . 66 ft . (20m)
Takes any settings back to Start
(Starts over at preset settings, but
does not erase pairing)
Increases the speed of whatever
RGB program running
Starts the pre-set programs . Hit play
again stops that program . Hit play
again moves to the next program .
Speed-down Button
Decreases the speed of whatever
RGB program running
Zone 1 & Zone 2 Buttons
Switches between Zones 1 and 2
for independent zone functions

RGB and CCT full-function controls:

The Tresco FREEDiM Remote Control provides color and brightness
®
controls for RGB or CCT (white color-tunable) lighting on Tresco
voltage LED RGB and CCT lights . It also controls the intensity (dim
levels) of the lights up to 95% . The digital screen on the FREEDiM
Parent Controller displays the current mode and settings .
The wireless Remote Control must be positioned within 66 ft .
(20m) of Parent Controller and any Child Receivers . Note: outside
interference may affect the signal between Remote Control and
Parent Controller . (see 'Signal Interference' on page 2)
RGB and CCT modes:
Prior to installation you need to select between RGB or CCT LED
lights . Then after installation, you must select either RGB or CCT
mode on the Parent Controller . (see the Switch Mode button above,
in Fig 1)
See separate instruction sheets for further information on Tresco®
low voltage LED RGB and CCT lights, FREEDiM Parent Controllers
and Child Receivers, and Power Supplies.
(included)
Home Button
G
R
Speed-up Button
3500K
3000K 5000K
R G
Play Button Z1
3000K 3500K
R G B
Z1
3000K 3500K 5000K
R G R B G B
Z1 Z2
R G B
3000K 3500K 3000K 5000K 3500K 5000K
3000K 3500K 5000K
Z2 Z2
Z1 Z1
Z1 Z2
Zone 1 Indicator Light
FREEDiM Dynamic RF Remote Control
For RGB & CCT LEDs • 12VDC 60W & 24VDC 96W
1
#
B
B
Z2
5000K
R G
3000K 3500K 5000K
Z2
Z1
RGB Indicator Light

Pairing the Remote Control to the Parent Controller

1 . First install the Parent Controller with either a RGB or CCT LED light system
low
®
and then turn on the Parent Controller .
2 . Check the mode on the Parent Controller and select either RGB or CCT mode
depending on the LED light system installed .
3 . On the Remote Control hit the ON button
- The small indicator light in top corner is now red, indicating that the Remote
Control is live and active (this light stays on for 30 sec .) (see Fig. 1 above) .
4 . Using the Switch Mode button
indicator light underneath the Switch Mode button indicates RGB mode .
5 . On the Parent Controller press the Learning Key one time .
6 . Next on the Remote Control press the Zone 1 button
light underneath is now red (see Fig. 1 above) .
7 . After you have hit the Zone 1 button, touch either the RGB Color Wheel or
CCT Slider . Lights will flash once indicating everything is paired .
Then repeat steps if adding Zone 2 or more Parent Controllers .
Note: Each zone can control 1 Parent Controller and up to 10 Child Receivers .
Each zone is independent and must be controlled separately from each
other . (see more information and illustration on page 2)
Instructions
"On" Indicator Light
CCT Slider
for CCT control
(slide with finger touch)
RGB Color Wheel
for RGB control
(rotate with finger touch)
"On/Off" Button
Dim Button
Dims up or down
R G B
R R R G G G
3000K 3500K 5000K
Quick preset buttons –
B
3000K 3000K 3000K 3500K 3500K 3500K
In RGB mode, quickly go to
Z1 Z2
preset Red, Green or Blue colors
R R R G G G
Z1 Z1 Z1
Z2 3000K 3000K 3000K 3500K 3500K 3500K
Quick preset buttons –
R G B
Z1 Z1 Z1
In CCT mode, quickly go to preset
Warm (3000K), Neutral (3500K),
or Cool (5000K) light
3000K 3500K 5000K
Z1 Z2
Switch Mode
Switches unit between RGB and
CCT modes
Zone 2 Indicator Light
.
R G B
R G
3000K 3500K 5000K
, select either RGB or CCT mode . The red
Z1 Z2
3000K 3500K
Z1
(Instructions continued on page 2)
B B B
RGB Buttons
5000K 5000K 5000K
B B B
Z2 Z2 Z2
5000K 5000K 5000K
CCT Buttons
Z2 Z2 Z2
B
5000K
Z2
R G B
3000K 3500K 5000K
. The Zone 1 indicator
Z1 Z2