OBD2 SCANZ User Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

OBD2 SCANZ

BAT Check

Setup

Table of Contents

Summary of Contents for OBD2 SCANZ

Page 1 OBD2 SCANZ BAT Check Setup...
Page 3: Safety Precautions
Safety precautions To avoid body injury and damage to the device or your car, please read this manual carefully before using it. The testing process described in the manual is generally the experience of technician. Safety precaution is required in most of the process to avoid body injury and damage to the device or your car.
Page 4: Product Specification
1. coverage： 1) Support vehicles for VW, AUDI, SKODA, SEAT and BENTLEY etc . 2) Supports all VW diagnostic protocols: UDS, TP20, TP16, KWP2000 and KWP1281. Supports all OBDII/EOBD protocols : VPW, PWM, ISO, KWP 2000 and CAN 2. Product specification ▪...
Page 5 3. Appearance and buttons description BAT Check Setup...
Page 6 LCD DISPLAY – Indicates test results. Backlit, 320 x 240 pixels display. [OK] BUTTON – Confirms a selection (or action) from a menu. ESC BUTTON – Cancels a selection (or action) from a menu or returns to the menu. [LEFT ]SCROLL BUTTON –in the menu mode through the menu and sub menu move to the left, when rolling in a data interface, use the left button can be moved to the last screen.
Page 7 OPERATION INSTRUCTIONS 1. Connect OBD2 SCANZ 1.1 Turn the ignition on. 1.2 Locate the vehicle's 16-pin Data Link Connector (DLC). 2. OBD2 SCANZ Features 2.1 For VW Choose [For VW ] and then select [Vehicle Scan]. As follows: Select Menu...
Page 8 2.1.1 Choose [System Scan ], select [ 0017-Dash Board], The screen displays as follows: Select System Select Function 0017-Dash Board 01-Version Information 0019-Gateway 02-Read Fault Codes 0061-Battery Regulation 03-Erase Fault Codes 04-Read Datastream 05-Basic Setting 07-Adaptation 08-Access Authorization 2.1.1.1 Choose [ 01-version information ] The screen displays as follows: 01-Version Information 01-Version Information...
Page 9 2.1.1.3 Choose[ Erase fault codes ], then press [OK] button . The screen displays as follows Information Information Erase fault codes had success. Please wait 10 seconds, Turn ignition Erase fault codes! off and Switch on again. Are you sure? Read fault codes to verify.
Page 10 2.1.1.6 Choose [ Adaptation ], select [ Input channel ], if enter number:005. The screen displays as follows: 07-Adaptation Input channel Input channel Select Function Delete lnput a channel number (0~255) 3/12 07-Adaptation 07-Adaptation This function is not supported feedback) to save the test on this vehicle records, Carry out vehicle test Note!
Page 11: Access Authorization
2.1.1.7 Access Authorization Select Function 08-Access Authorization 01-Version Information 02-Read Fault Codes Delete 03-Erase Fault Codes Login code (Enter five 04-Read Datastream decimal digits) 05-Basic Setting 07-Adaptation 08-Access Authorization 3/12 2.1.2 Gate way Select System Select Function 0017-Dash Board 01-Version Information 0019-Gateway 02-Read Fault Codes 0061-Battery Regulation...
Page 12 2.2 System Selection: 2.2.1 Choose [ System Selection ], click [ Common System], Select Menu Select System Common System 0001-Engine Control Modu... All Systems 0002-Transmission Contro... 0003-Brakes 1 0008-Air Conditioning 0009-Central Electrics 0015-Airbag 0016-Steering Column Ele... 1/14 Select one system to test, more operations, please refer to 2.1.1 to2.1.3 Select Function 01-Version Information...
Page 13 2.3 Crafter (LT3) test: Select Menu System Scan System Scan System Selection Manual Select Crafter(LT3) 2006-2017 Special Functions Scanning...[3%} 0001-Engine Control Modu... 2.4 Special Functions: Choose [Special Functions], Select Menu Special Functions System Scan Service Reset System Selection Throttle Learning Crafter(LT3) 2006-2017 EPB ReplaceBrakePads...
Page 14 Choose one of special functions, such as [Service Reset]. Press [ OK ] to continue: Service Reset Service Reset Flexible lnterval Fixed lnterval Choose [Flexible Interval], It displays as follows: Service Reset Flexible lnterval Service Reset CH:42 Min Mileage:15000km Flexible lnterval CH:42 Min Mileage:30000km Fixed lnterval CH:49 Min Time lnterval:36...
Page 15 Service Reset Service Reset Flexible lnterval Fixed lnterval Remark: Before setting the maintenance interval, do set the corresponding [ oil quality ] If vehicle uses UDS protocol, you could do inspection due reset, service reset, and mileage and time settings. Settings of mileage and time support be input manually with any value you want.
Page 16 Retract the brake pump , please pay attention to the operation tips, and press [OK] button to continue: EPB ReplaceBrakePads Information Replace the brake pads. Has been performed, After finish, Press [OK] to Press [OK] to continue. continue. EPB ReplaceBrakePads Information Please check complete Has been performed,...
Page 17 3.2 Choose [Retraction Brackpump] , press [ OK ] to continue: Information Perform this function Are you sure? 3.2.1 After retract brakepump, press [ OK ] to continue: EPB ReplaceBrakePads Has been performed, Press [OK] to continue. 3.2.2 Check whether the retraction is completely, then start to replace the brake pads.
Page 18 3.3 Choose [Release Brake Pump] , press [ OK ] to continue: EPB ReplaceBrakePads Information EPB ReplaceBrakePads Retraction BrakePump Perform this function Release Brake Pump Are you sure? 3.3.1 Release Brake Pump, and press [ OK ] to continue: EPB ReplaceBrakePads Information Has been performed, Please check complete release...
Page 19 4.1 Press [ OK ] button again , The screen will displays old battery parameters. It is better to record the parameters to prevent the old battery parameters from being restored when the new battery parameters are not available. Battery Registration Press [OK] to continue Description Battery Value Capacity(Ah) :95Ah...
Page 20: Obdii Diagnosis
Information Has been performed, Press [OK] to continue. 5. OBDII diagnosis 5.1 Read Codes Stored codes are also known as "hard codes" or "permanent codes". These codes cause the control module to illuminate the malfunction indicator lamp (MIL) when an emission-related fault occurs.
Page 21: Erase Codes
indicates "No (pending) codes are stored in the module!" Wait a few seconds or press any key to return to the Diagnostic Menu. 2) View DTCs and their definitions on screen. P0143 Generic Current O2 Sensor Circuit Low Voltage Bank 1 Sensor 3 The control module number, sequence of the DTCs, total number of codes detected and type of codes (Generic of Manufacturer specific) will be observed on the upper right hand...
Page 22 2) A warning message comes up asking for your confirmation. Erase Codes Clear/Reset Emission-Related Diagnostic Information, AreYou sure? 3) Press [OK] to confirm. Erase Codes Erase Codes Please Turn Ignition ON with Emission-Related Diagnostic Engine Off, Press OK key to Information has been cleared! continue! 5.3 I/M Readiness...
Page 23: Press Enter
Diagnostic Menu I/M Readiness Read Codes Since DTCs Were Cleared Erase Codes This Drive Cycle I/M Readiness Data Stream Evap System Test Vehicle Information 5.4 Data Stream The OBDII Scan Tool is a special diagnostic tool that communi- cates with the vehicle’s computer. The Scan Tool lets you view “real-time”...
Page 24: Vehicle Information
Diagnostic Menu Evap System Test Read Codes Erase Codes Evaportive system leak test I/M Readiness not supported Data Stream Evap System Test Vehicle Information 5.6 Vehicle Information. Select [Vehicle Information] and press [ENTER],the screen will display the information such as VIN (Vehicle identification Number），CID（Calibration ID）and CVN (Calibration verify number).
Page 25: Unit Of Measure
6.2 Beeper Choose [Beeper] and it displays as follows: Tool Setup Beeper Language Beeper Instructions(Display at startup) Unit of Measure Skin Style Feedback Device Information 6.3 Instructions Choose [Instructions] and it displays as follows: Tool Setup Instrucions(Display at startup) Language Beeper Instructions(Display at startup) Unit of Measure...
Page 26 Next : Press EXIT Button and return to the main menu. Choose [OBDII] menu to detecting again and it will record the data. 2）Transfer data to your computer and generate feedback file. Download upgrade file on the computer from OBD2 SCANZ website. The device is connected with computer through USB cable.
Page 27 Choose “Update” file and it displays as follow: Click “Feedback” and it displays as follow:...
Page 28: Device Information
Device Information Language Software Version: Beeper V1.16.000 Instructions(Display at startup) Library Version: Unit of Measure V1.00.000 Skin Style Serial Number: Feedback Obd2 scanz20170500281904 Device Information 7. Update 1. Download update software 2. Connect the device with computer through USB cable.
Page 29 3. The update software is only supported by 7/8/10. * Windows 8/10 can run update software directly, * Click "install driver.bat" in the driver files to install the driver, if computer system is Windows 7...
Page 30 OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ OBD2 SCANZ...
Page 32 E-mail: support@obd2scanz.com Website: www.obd2scanz.com...